Reseted DEVADDR field in DCFG to zero on USB RESET.

Device address in DCFG register does not reset to zero,
which required to pass enumeration, after disconnect and
reconnect.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

USB support in the Meson8 SoCs is provided by a DWC2 controller which
works with the same settings as Meson8b and GXBB. Using the generic
"snps,dwc2" binding results in an endless stream of "Overcurrent change
detected" messages.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

As of commit bb475230 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.

This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This patch introduces a new parameter to activate USB OTG HS/FS core
embedded phy transceiver. The STM32F4x9 SoC uses the GGPIO register
to enable the transceiver.
Also add the dwc2_set_params function for stm32f4 otg fs.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NBruno Herrera <bruherrera@gmail.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

I had seen some odd behavior with HiKey's usb-gadget interface
that I finally seemed to have chased down. Basically every other
time I plugged in the OTG port, the gadget interface would
properly initialize. The other times, I'd get a big WARN_ON
in dwc2_hsotg_init_fifo() about the fifo_map not being clear.

Ends up if we don't disconnect the gadget state, the fifo-map
doesn't get cleared properly, which causes WARN_ON messages and
also results in the device not properly being setup as a gadget
every other time the OTG port is connected.

So this patch adds a call to dwc2_hsotg_disconnect() in the
reset path so the state is properly cleared.

With it, the gadget interface initializes properly on every
plug in.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

a lot of embeded system SOC (e.g. freescale T2080) have both
PCI and USB modules. But USB module is controlled by registers directly,
it have no relationship with PCI module.

when say N here it will not build PCI related code in USB driver.
Signed-off-by: Nyuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Acked-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The irq is available in hsotg already, so there's no need to
pass it as separate function parameter.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Set the iomem parameters in the usb_hcd to fix this misleading
message during driver load:
dwc2 c9100000.usb: irq 22, io mem 0x00000000
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Add dwc2_check_param_tx_fifo_sizes function which validates
the members of g_tx_fifo_size array and sets to average or
default values if it is needed.

Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NSevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Remove legacy DWC2_G_P_LEGACY_TX_FIFO_SIZE array for TX FIFOs.
Update dwc2_set_param_tx_fifo_sizes function to calculate
and assign default average FIFO depth to each member of
g_tx_fifo_size array. Total FIFO size, EP Info block's size,
FIFO operation mode and device operation mode are taken into
consideration during the calculation.

Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NSevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

GDFIFOCFG is available from IP version 2.91a. Fix the code to reflect
this.
Signed-off-by: NSevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 100ms delays here passing the adjusted "min"
value to msleep(). This helps reduce the load on the hrtimer subsystem.

Link: http://lkml.org/lkml/2017/1/11/377
Fixes: commit 2938fc63 ("usb: dwc2: Properly account for the force mode delays")
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The Hi6220's usb controller is limited in that it does not
support "Split Transactions", so it does not support communicating
with low-speed and full-speed devices behind a high-speed hub.

Thus it requires a quirk so that we can manually drop the usb
speed when low/full-speed are attached, and bump back to high
speed when they are removed.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NChen Yu <chenyu56@huawei.com>
[jstultz: Reworked to simplify the patch, and made
 commit log to be more specific about the issue]
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

We've seen failures when switching between host and gadget mode,
which was diagnosed as being caused due to the bus being
auto-suspended when we switched.

So this patch forces a port resume when switching to device
mode if the bus is suspended.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NChen Yu <chenyu56@huawei.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

When removing a USB-A to USB-otg adapter cable, we get a change status
irq, and then in dwc2_conn_id_status_change, we erroneously see the
GOTGCTL_CONID_B flag set. This causes us to get stuck in the
"while (!dwc2_is_device_mode(hsotg))" loop, spitting out "Waiting for
Peripheral Mode, Mode=Host" warnings until it fails out many seconds
later.

This patch works around the issue by re-reading the GOTGCTL state to
check if the GOTGCTL_CONID_B is still set and if not restarting the
change status logic.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Reviewed-by: NVardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Basically when plugging in various cables in different orders, I'm
occasionally seeing the following BUG splat:

[   86.215403] BUG: scheduling while atomic: kworker/u16:2/53/0x00000002
[   86.219164] usb 1-1: USB disconnect, device number 9
[   86.226845] Preemption disabled at:[   86.230218]
[<ffffff8008673558>] dwc2_conn_id_status_change+0x120/0x250
[   86.236894] CPU: 0 PID: 53 Comm: kworker/u16:2 Tainted: G        W
     4.9.0-rc8-00051-gd5a7979-dirty #1702
[   86.246836] Hardware name: HiKey Development Board (DT)
[   86.252100] Workqueue: dwc2 dwc2_conn_id_status_change
[   86.257279] Call trace:
[   86.259771] [<ffffff8008087c28>] dump_backtrace+0x0/0x1a0
[   86.265210] [<ffffff8008087ddc>] show_stack+0x14/0x20
[   86.270308] [<ffffff80084343f0>] dump_stack+0x90/0xb0
[   86.275401] [<ffffff80080d8d94>] __schedule_bug+0x6c/0xb8
[   86.280841] [<ffffff8008a07220>] __schedule+0x4f8/0x5b0
[   86.286099] [<ffffff8008a073e8>] schedule+0x38/0xa0
[   86.291017] [<ffffff8008a0a6cc>] schedule_hrtimeout_range_clock+0x8c/0xf0
[   86.297846] [<ffffff8008a0a740>] schedule_hrtimeout_range+0x10/0x18
[   86.304150] [<ffffff8008a0a4a0>] usleep_range+0x50/0x58
[   86.309418] [<ffffff800866d8dc>] dwc2_wait_for_mode.isra.4+0x54/0xd0
[   86.315815] [<ffffff800866f058>] dwc2_core_reset+0xe0/0x168
[   86.321431] [<ffffff800867e364>] dwc2_hsotg_core_init_disconnected+0x2c/0x310
[   86.328602] [<ffffff8008673568>] dwc2_conn_id_status_change+0x130/0x250
[   86.335254] [<ffffff80080ccd48>] process_one_work+0x118/0x370
[   86.341035] [<ffffff80080ccfe8>] worker_thread+0x48/0x498
[   86.346473] [<ffffff80080d2eb0>] kthread+0xd0/0xe8
[   86.351299] [<ffffff8008082e80>] ret_from_fork+0x10/0x50

This seems to be caused by the dwc2_wait_for_mode() calling
usleep_range() while the hstog->lock spinlock is held, since
we take that before calling dwc2_hsotg_core_init_disconnected().

This patch avoids the issue by adding an extra argument to
dwc2_core_reset(), as suggested by John Youn, which allows us to
skip the waiting, which should be unnecessary when calling from
dwc2_hsotg_core_init_disconnected().

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Show the value of dr_mode via a debufs file.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Remove debugging prints to show params.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Show the core params and hardware params.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Further reduce the set of parameters set by platforms. Many of them are
unnecessary as they should be reported by hardware. They should only
need to be overridden if there is a problem.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Check these parameters only for true or false. There is no need to check
for greater or less than 0.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Remove the platform-specific static param structs and set only those
params that are necessary for each platform.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Check that core parameters have valid values and adjust them if they
aren't.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Group the members by global, host, and gadget params. Formatting and
organizational change only.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Update the param types to appropriately sized ints and bools.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

After setting the default core parameter values, read in the device
properties and modify core parameter values if needed.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Initialize the core parameters to their default, auto-detected values.

Remove all the previous dwc2_set_param* methods. Most of what this code
is doing is handling defaults for "not set" values and other trivial
checks. The checking can be simplified and will be done in a later
commit.

This allows us to change only those parameters that won't work with
default settings. It also allows us to use non-int parameters.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The otg_ver parameter only controls the SRP pulsing method and defaults
to the 1.3 behavior. It is unused and can be removed.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Add programming of GDFIFOCFG register in device mode.
It must contain start address for EP Info block and
total FIFO depth.
Signed-off-by: NSevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Take the sizeof '*req' instead of 'struct dwc2_hsotg_req'.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The function returns void so a return is unnecessary.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The indent should be only one tab.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Fix lines over 80 characters.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

* Remove braces for one-line statements
* Add missing braces where another arm in if-statement uses braces
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Fix the formatting of logical statements to end the line with the
logical operator.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Fix misaligned and over 80-character comments.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Fixes checkpatch warning:

WARNING: function definition argument 'struct dwc2_hsotg *' should also
have an identifier name
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This commmit is the result of running checkpatch --fix.

The results were verified for correctness. Some of the fixes result in
line over 80 char which we will fix manually later.

The following is a summary of what was done by checkpatch:
* Remove externs on function prototypes.
* Replace symbolic permissions with octal.
* Align code to open parens.
* Replace 'unsigned' with 'unsigned int'.
* Remove unneccessary blank lines.
* Add blank lines after declarations.
* Add spaces around operators.
* Remove unnecessary spaces after casts.
* Replace 'x == NULL' with '!x'.
* Replace kzalloc() with kcalloc().
* Concatenate multi-line strings.
* Use the BIT() macro.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

For boolean variables true/false is preferred over 1/0 for readability.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 20+ ms delays here passing the adjusted "min"
value to msleep(). This helps reduce the load on the hrtimer subsystem.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>