2.6.31-rc introduced an architecture level set checker based on facility
bits. e.g. if the kernel is compiled to run only on z9, several facility
bits are checked very early and the kernel refuses to boot if a z9 specific
facility is missing.
Until now kvm on s390 did not implement the store facility extended (STFLE)
instruction. A 2.6.31-rc kernel that was compiled for z9 or higher did not
boot in kvm. This patch implements stfle.

This patch should go in before 2.6.31.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This patch reworks the s390 clock comparator wakeup to hrtimer. The clock
comparator is a per-cpu value that is compared against the TOD clock. If
ckc <= TOD an external interrupt 1004 is triggered. Since the clock comparator
and the TOD clock have a much higher resolution than jiffies we should use
hrtimers to trigger the wakeup. This speeds up guest nanosleep for small
values.

Since hrtimers callbacks run in hard-irq context, I added a tasklet to do
the actual work with enabled interrupts.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NChristian Ehrhardt <ehrhardt@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Currently the storage of the machine flags is a globally exported unsigned
long long variable. By moving the storage location into the lowcore struct we
allow assembler code to check machine_flags directly even without needing a
register. Addtionally the lowcore and therefore the machine flags too will be
in cache most of the time.
Signed-off-by: NChristian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove the remaining arch fragments of the old guest debug interface
that now break non-x86 builds.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Lets fix the name for the lctlg instruction...
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

All registers are unsigned long types. This patch changes all occurences
of guestaddr in gaccess from u64 to unsigned long.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

While doing some tests with our lcrash implementation I have seen a
naming conflict with prefix_info in kvm_host.h vs. addrconf.h

To avoid future conflicts lets rename private definitions in
asm/kvm_host.h by adding the kvm_s390 prefix.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

From: Martin Schwidefsky <schwidefsky@de.ibm.com>

This patch fixes a bug with cpu bound guest on kvm-s390. Sometimes it
was impossible to deliver a signal to a spinning guest. We used
preemption as a circumvention. The preemption notifiers called
vcpu_load, which checked for pending signals and triggered a host
intercept. But even with preemption, a sigkill was not delivered
immediately.

This patch changes the low level host interrupt handler to check for the
SIE  instruction, if TIF_WORK is set. In that case we change the
instruction pointer of the return PSW to rerun the vcpu_run loop. The kvm
code sees an intercept reason 0 if that happens. This patch adds accounting
for these types of intercept as well.

The advantages:
- works with and without preemption
- signals are delivered immediately
- much better host latencies without preemption
Acked-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch introduces interpretation of some diagnose instruction intercepts.
Diagnose is our classic architected way of doing a hypercall. This patch
features the following diagnose codes:
- vm storage size, that tells the guest about its memory layout
- time slice end, which is used by the guest to indicate that it waits
  for a lock and thus cannot use up its time slice in a useful way
- ipl functions, which a guest can use to reset and reboot itself

In order to implement ipl functions, we also introduce an exit reason that
causes userspace to perform various resets on the virtual machine. All resets
are described in the principles of operation book, except KVM_S390_RESET_IPL
which causes a reboot of the machine.
Acked-by: NMartin Schwidefsky <martin.schwidefsky@de.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

This patch introduces in-kernel handling of _some_ sigp interprocessor
signals (similar to ipi).
kvm_s390_handle_sigp() decodes the sigp instruction and calls individual
handlers depending on the operation requested:
- sigp sense tries to retrieve information such as existence or running state
  of the remote cpu
- sigp emergency sends an external interrupt to the remove cpu
- sigp stop stops a remove cpu
- sigp stop store status stops a remote cpu, and stores its entire internal
  state to the cpus lowcore
- sigp set arch sets the architecture mode of the remote cpu. setting to
  ESAME (s390x 64bit) is accepted, setting to ESA/S390 (s390, 31 or 24 bit) is
  denied, all others are passed to userland
- sigp set prefix sets the prefix register of a remote cpu

For implementation of this, the stop intercept indication starts to get reused
on purpose: a set of action bits defines what to do once a cpu gets stopped:
ACTION_STOP_ON_STOP  really stops the cpu when a stop intercept is recognized
ACTION_STORE_ON_STOP stores the cpu status to lowcore when a stop intercept is
                     recognized
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

This patch introduces in-kernel handling of some intercepts for privileged
instructions:

handle_set_prefix()        sets the prefix register of the local cpu
handle_store_prefix()      stores the content of the prefix register to memory
handle_store_cpu_address() stores the cpu number of the current cpu to memory
handle_skey()              just decrements the instruction address and retries
handle_stsch()             delivers condition code 3 "operation not supported"
handle_chsc()              same here
handle_stfl()              stores the facility list which contains the
                           capabilities of the cpu
handle_stidp()             stores cpu type/model/revision and such
handle_stsi()              stores information about the system topology
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

This patch contains the s390 interrupt subsystem (similar to in kernel apic)
including timer interrupts (similar to in-kernel-pit) and enabled wait
(similar to in kernel hlt).

In order to achieve that, this patch also introduces intercept handling
for instruction intercepts, and it implements load control instructions.

This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both
the vm file descriptors and the vcpu file descriptors. In case this ioctl is
issued against a vm file descriptor, the interrupt is considered floating.
Floating interrupts may be delivered to any virtual cpu in the configuration.

The following interrupts are supported:
SIGP STOP       - interprocessor signal that stops a remote cpu
SIGP SET PREFIX - interprocessor signal that sets the prefix register of a
                  (stopped) remote cpu
INT EMERGENCY   - interprocessor interrupt, usually used to signal need_reshed
                  and for smp_call_function() in the guest.
PROGRAM INT     - exception during program execution such as page fault, illegal
                  instruction and friends
RESTART         - interprocessor signal that starts a stopped cpu
INT VIRTIO      - floating interrupt for virtio signalisation
INT SERVICE     - floating interrupt for signalisations from the system
                  service processor

struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting
an interrupt, also carrys parameter data for interrupts along with the interrupt
type. Interrupts on s390 usually have a state that represents the current
operation, or identifies which device has caused the interruption on s390.

kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a
disabled wait (that is, disabled for interrupts), we exit to userspace. In case
of an enabled wait we set up a timer that equals the cpu clock comparator value
and sleep on a wait queue.

[christian: change virtio interrupt to 0x2603]
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

This path introduces handling of sie intercepts in three flavors: Intercepts
are either handled completely in-kernel by kvm_handle_sie_intercept(),
or passed to userspace with corresponding data in struct kvm_run in case
kvm_handle_sie_intercept() returns -ENOTSUPP.
In case of partial execution in kernel with the need of userspace support,
kvm_handle_sie_intercept() may choose to set up struct kvm_run and return
-EREMOTE.

The trivial intercept reasons are handled in this patch:
handle_noop() just does nothing for intercepts that don't require our support
  at all
handle_stop() is called when a cpu enters stopped state, and it drops out to
  userland after updating our vcpu state
handle_validity() faults in the cpu lowcore if needed, or passes the request
  to userland
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

This patch contains the port of Qumranet's kvm kernel module to IBM zSeries
 (aka s390x, mainframe) architecture. It uses the mainframe's virtualization
instruction SIE to run virtual machines with up to 64 virtual CPUs each.
This port is only usable on 64bit host kernels, and can only run 64bit guest
kernels. However, running 31bit applications in guest userspace is possible.

The following source files are introduced by this patch
arch/s390/kvm/kvm-s390.c    similar to arch/x86/kvm/x86.c, this implements all
                            arch callbacks for kvm. __vcpu_run calls back into
                            sie64a to enter the guest machine context
arch/s390/kvm/sie64a.S      assembler function sie64a, which enters guest
                            context via SIE, and switches world before and after                            that
include/asm-s390/kvm_host.h contains all vital data structures needed to run
                            virtual machines on the mainframe
include/asm-s390/kvm.h      defines kvm_regs and friends for user access to
                            guest register content
arch/s390/kvm/gaccess.h     functions similar to uaccess to access guest memory
arch/s390/kvm/kvm-s390.h    header file for kvm-s390 internals, extended by
                            later patches
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>