- 13 9月, 2015 1 次提交
-
-
由 Guenter Roeck 提交于
NCT6793D is register compatible with NCT6792D. Also move nct6775_sio_names[] closer to enum kinds to simplify adding new chips. Tested-by: NGrazvydas Ignotas <notasas@gmail.com> Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 27 8月, 2015 1 次提交
-
-
由 Huang Rui 提交于
This patch updates description of fam15h_power driver, its scope is extended to family 16h processsors. Signed-off-by: NHuang Rui <ray.huang@amd.com> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 20 8月, 2015 1 次提交
-
-
由 Guenter Roeck 提交于
LTM2975 is a dual 9A or single 18A μModule regulator. It is register compatible with LTM4676. Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 18 8月, 2015 3 次提交
-
-
由 Guenter Roeck 提交于
LTC3886 is a is a dual PolyPhase DC/DC synchronous step-down switching regulator controller. It is mostly command compatible to LTC3883, but supports two phases instead of one. Suggested-by: NMichael Jones <mike@proclivis.com> Tested-by: NMichael Jones <mike@proclivis.com> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Guenter Roeck 提交于
LTC2980 and LTM2987 are command compatible to LTC2977. They consist of two LTC2977 on a single die, and are instantiated as two separate chips, each supporting eight channels. Suggested-by: NMichael Jones <mike@proclivis.com> Tested-by: NMichael Jones <mike@proclivis.com> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Guenter Roeck 提交于
LTC2975 is mostly compatible to LTC2974, but supports input current and power measurement. Tested-by: NMichael Jones <mike@proclivis.com> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 13 8月, 2015 2 次提交
-
-
由 Guenter Roeck 提交于
LTC3887 is an enhanced version of LTC3880 and supports the same commands. Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Guenter Roeck 提交于
LTC3882 is mostly compatible with LTC3880. Major differences are that it does not measure the input current, and it no longer supports LTC's legacy mechanism to identify the chip. Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 11 8月, 2015 1 次提交
-
-
由 Guenter Roeck 提交于
Add device IDs and references for Texas Instruments TPS544B20, TPS544B25, TPS544C20, and TPS544C25 to the generic PMBus driver. Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 10 8月, 2015 4 次提交
-
-
由 Guenter Roeck 提交于
MAX20751 is a multiphase power controller with internal buck converter. It uses VR12.0 to report the output voltage. This requires an explicit driver, since the VR version can not be auto-detected. The chip supports a manufacturer specific command to fine-tune the output voltage. This command is not currently supported. Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Justin Maggard 提交于
Add support for the IT8732F. This chip is pretty similar to IT8721F, with the main difference being that the ADC LSB is 10.9 mV instead of 12 mV. Signed-off-by: NJustin Maggard <jmaggard@netgear.com> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Constantine Shulyupin 提交于
Introduced REG_PWM, pwm[1..3]_auto_point[1..5]_temp, pwm[1..3]_auto_point[1..5]_pwm, nct7802_auto_point_attrs, nct7802_auto_point_group, updated nct7802_regmap_is_volatile Signed-off-by: NConstantine Shulyupin <const@MakeLinux.com> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Guenter Roeck 提交于
ADM1293 and ADM1294 are mostly compatible with other chips of the same series, but have more configuration options. There are also some differences in register details. Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 30 7月, 2015 1 次提交
-
-
由 Guenter Roeck 提交于
pwm attributes have well defined names, which should be used. Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru> Cc: stable@vger.kernel.org #v4.1+ Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 03 7月, 2015 2 次提交
-
-
由 Jean Delvare 提交于
Add an item to the checklist when submitting a new hwmon driver: only some I2C addresses can be probed, others should not for safety reasons. Signed-off-by: NJean Delvare <jdelvare@suse.de> Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Roger Lucas 提交于
Add pwm[4-7] and the associated pwm[4-7]_mode attributes. Signed-off-by: NRoger Lucas <vt8231@hiddenengine.co.uk> Signed-off-by: NJean Delvare <jdelvare@suse.de>
-
- 22 6月, 2015 1 次提交
-
-
由 Maciej S. Szmigiero 提交于
Add hwmon driver for the Microchip TC74. The TC74 is a single-input 8-bit I2C temperature sensor, with +-2 degrees centigrade accuracy. Signed-off-by: NMaciej Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 01 6月, 2015 1 次提交
-
-
由 Beomho Seo 提交于
This patch adds support for the ntc thermistor NCPXXWF104 series. Cc: Jean Delvare <jdelvare@suse.de> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: NBeomho Seo <beomho.seo@samsung.com> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 30 5月, 2015 1 次提交
-
-
由 Guenter Roeck 提交于
I2C address 0x37 may be used by EEPROMs, which can result in false positives. Do not attempt to detect a chip at this address. Reviewed-by: NJean Delvare <jdelvare@suse.de> Cc: stable@vger.kernel.org # v4.0+ Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 05 4月, 2015 2 次提交
-
-
由 Guenter Roeck 提交于
IT8620E is mostly compatible to IT7828F. Add generic support for it. IT8620E supports up to 6 fan tachometers and 6 pwm controls. Support for the 6th tachometer and for the additional pwm controls are addded in separate patches. Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Guenter Roeck 提交于
IT8790E is a super-IO chip with three fan tachometers. It is mostly compatible to IT8728F, but only supports three fan tachometers instead of five. Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 10 3月, 2015 4 次提交
-
-
由 Vadim V. Vlasov 提交于
The NCT7904D is a hardware monitor supporting up to 20 voltage sensors, internal temperature sensor, Intel PECI and AMD SB-TSI CPU temperature interface, up to 12 fan tachometer inputs, up to 4 fan control channels with SmartFan. Signed-off-by: NVadim V. Vlasov <vvlasov@dev.rtsoft.ru> [Guenter Roeck: Fixed whitespace errors, dropped redundant comment] Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Thomas Lorblanches 提交于
IT8786E is mostly compatible with IT8771 / IT8772. Parameters determined by testing various combinations. Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NThomas Lorblanches <zlika_ese@hotmail.com> [Guenter Roeck: merged from github, addressed review comments] Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Guenter Roeck 提交于
TS3000GB0 has a new device ID (0x2913). Since IDT's datasheets suggest that the upper 8 bit of the device ID reflect the chip ID and the lower 8 bit reflect the version number, modify the code to accept all chips with ID 0x29xx. Also add support for TS3001 and TSE2004. Some of the datasheets for older chips are no longer available from the IDT web site, so replace explicit links in the documentation with a generic note. Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Guenter Roeck 提交于
IT8781F is mostly compatible to IT8782F. Major difference is that it only supports four instead of six UART channels, and therefore does not share the uart6 pins. Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 26 1月, 2015 3 次提交
-
-
由 Kevin Hilman 提交于
Add support for "ina231" as compatible string, and update Documentation and Kconfig accordingly. Tested with the Exynos5422-based odroid-xu3 board which has on-board INA231 sensors. Signed-off-by: NKevin Hilman <khilman@linaro.org> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Bartosz Golaszewski 提交于
This attribute allows to configure the update interval of ina226. Although the bus and shunt voltage conversion times remain hardcoded to 1.1 ms, we can now modify said interval by changing the averaging rate. While we're at it - add an additional variable to ina2xx_data, which holds the current configuration settings - this way we'll be able to restore the configuration in case of an unexpected chip reset. Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Bartosz Golaszewski 提交于
The shunt resistance can only be set via platform_data or device tree. This isn't suitable for devices in which the shunt resistance can change/isn't known at boot-time. Add a sysfs attribute that allows to read and set the shunt resistance. Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 08 12月, 2014 1 次提交
-
-
由 Guenter Roeck 提交于
TMP435 supports a range of I2C addresses, not just 0x4c. Cc: Patrick Titiano <ptitiano@baylibre.com> Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com> Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 05 12月, 2014 1 次提交
-
-
由 Patrick Titiano 提交于
Signed-off-by: NPatrick Titiano <ptitiano@baylibre.com> [Bartosz Golaszewski: prepared for submission, code review fixes] Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com> [Guenter Roeck: Merged two patches into one] Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 02 12月, 2014 2 次提交
-
-
由 Guenter Roeck 提交于
LM95233 is similar to LM95234, but it only supports two instead of four external temperature sensors. Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Guenter Roeck 提交于
LM95235 is register compatible to LM95245. Also update link to LM95245 data sheet, and drop the link to the datasheet from the driver source to simplify code maintenance. Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 01 12月, 2014 4 次提交
-
-
由 Guenter Roeck 提交于
NCT6792D is similar to NCT6791D. Only beep control and temperature monitoring registers are different. Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Guenter Roeck 提交于
Document support for NCT6102D/NCT6104D/NCT6106D and NCT6791D. Document that NCT5573D is compatible to NCT6775F with the same chip ID. Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Michael Thalmeier 提交于
It is basically a faster lm75 with improved (11 bit) resolution. Signed-off-by: NMichael Thalmeier <michael.thalmeier@hale.at> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Guenter Roeck 提交于
NCT7802Y is an I2C based hardware monitoring chip from Nuvoton. Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 24 9月, 2014 1 次提交
-
-
由 Andreas Werner 提交于
Added driver to support the 14F021P00 BMC Hardware Monitoring. The BMC is a Board Management Controller including monitoring of the board voltages. Signed-off-by: NAndreas Werner <andreas.werner@men.de> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NLee Jones <lee.jones@linaro.org>
-
- 23 9月, 2014 1 次提交
-
-
由 Aravind Gopalakrishnan 提交于
This patch adds temperature monitoring support for F15h M60h processor. - Add new pci device id for the relevant processor - The functionality of REG_REPORTED_TEMPERATURE is moved to D0F0xBC_xD820_0CA4 [Reported Temperature Control] - So, use this to get CUR_TEMP value - Since we need an indirect register access, protect this with a mutex lock - Add Kconfig, Doc entries to indicate support for this processor. Signed-off-by: NAravind Gopalakrishnan <aravind.gopalakrishnan@amd.com> Acked-by: NBorislav Petkov <bp@suse.de> Acked-by: NClemens Ladisch <clemens@ladisch.de> [Guenter Roeck: Declare new mutex and function static] Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
- 04 8月, 2014 2 次提交
-
-
由 Kamil Debski 提交于
The pwm-fan driver enables control of fans connected to PWM lines. This driver uses the PWM framework, so it is compatible with all PWM devices that provide drivers through the PWM framework. Signed-off-by: NKamil Debski <k.debski@samsung.com> Reviewed-by: NVarka Bhadram <varkabhadram@gmail.com> Reviewed-by: NTobias Klauser <tklauser@distanz.ch> [Guenter Roeck: Last argument to devm_of_pwm_get is pointer, use NULL] Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-
由 Neelesh Gupta 提交于
This patch adds basic kernel support for reading power values, fan speed rpm, voltage and temperature data on powernv platforms which will be exported to user space through sysfs interface. Test results: ------------- [root@tul163p1 ~]# sensors ibmpowernv-isa-0000 Adapter: ISA adapter fan1: 5465 RPM (min = 0 RPM) fan2: 5152 RPM (min = 0 RPM) fan3: 5521 RPM (min = 0 RPM) fan4: 4891 RPM (min = 0 RPM) fan5: 0 RPM (min = 0 RPM) fan6: 0 RPM (min = 0 RPM) fan7: 7480 RPM (min = 0 RPM) fan8: 7944 RPM (min = 0 RPM) temp1: +39.0°C (high = +0.0°C) power1: 190.00 W [root@tul163p1 ~]# ls /sys/devices/platform/ alarmtimer ibmpowernv.0 power rtc-generic serial8250 uevent [root@tul163p1 ~]# ls /sys/devices/platform/ibmpowernv.0/hwmon/hwmon0/ device fan2_min fan4_min fan6_min fan8_min power fan1_fault fan3_fault fan5_fault fan7_fault in1_fault power1_input fan1_input fan3_input fan5_input fan7_input in2_fault subsystem fan1_min fan3_min fan5_min fan7_min in3_fault temp1_input fan2_fault fan4_fault fan6_fault fan8_fault in4_fault temp1_max fan2_input fan4_input fan6_input fan8_input name uevent [root@tul163p1 ~]# ls /sys/class/hwmon/hwmon0/ device fan2_min fan4_min fan6_min fan8_min power fan1_fault fan3_fault fan5_fault fan7_fault in1_fault power1_input fan1_input fan3_input fan5_input fan7_input in2_fault subsystem fan1_min fan3_min fan5_min fan7_min in3_fault temp1_input fan2_fault fan4_fault fan6_fault fan8_fault in4_fault temp1_max fan2_input fan4_input fan6_input fan8_input name uevent [root@tul163p1 ~]# Signed-off-by: NNeelesh Gupta <neelegup@linux.vnet.ibm.com> Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
-