OVS keeps pointer to packet key in skb->cb, but the packet key is
store on stack. This could make code bit tricky. So it is better to
get rid of the pointer.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>

When there are multiple vlan headers present in a received frame, the first
one is put into vlan_tci and protocol is set to ETH_P_8021Q. Anything in the
skb beyond the VLAN TPID may be still non-linear, including the inner TCI
and ethertype. While ovs_flow_extract takes care of IP and IPv6 headers, it
does nothing with ETH_P_8021Q. Later, if OVS_ACTION_ATTR_POP_VLAN is
executed, __pop_vlan_tci pulls the next vlan header into vlan_tci.

This leads to two things:

1. Part of the resulting ethernet header is in the non-linear part of the
   skb. When eth_type_trans is called later as the result of
   OVS_ACTION_ATTR_OUTPUT, kernel BUGs in __skb_pull. Also, __pop_vlan_tci
   is in fact accessing random data when it reads past the TPID.

2. network_header points into the ethernet header instead of behind it.
   mac_len is set to a wrong value (10), too.
Reported-by: NYulong Pei <ypei@redhat.com>
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a bug where skb_clone() NULL check is missing in sample action
implementation.
Signed-off-by: NAndy Zhou <azhou@nicira.com>
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>

The sample action is rather generic, allowing arbitrary actions to be
executed based on a probability. However its use, within the Open
vSwitch
code-base is limited: only a single user-space action is ever nested.

A consequence of the current implementation of sample actions is that
depending on weather the sample action executed (due to its probability)
any side-effects of nested actions may or may not be present before
executing subsequent actions.  This has the potential to complicate
verification of valid actions by the (kernel) datapath. And indeed
adding support for push and pop MPLS actions inside sample actions
is one case where such case.

In order to allow all supported actions to be continue to be nested
inside sample actions without the potential need for complex
verification code this patch changes the implementation of the sample
action in the kernel datapath so that sample actions are more like
a function call and any side effects of nested actions are not
present when executing subsequent actions.

With the above in mind the motivation for this change is twofold:

* To contain side-effects the sample action in the hope of making it
  easier to deal with in the future and;
* To avoid some rather complex verification code introduced in the MPLS
  datapath patch.
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>

When sample action returns with an error, the skb has already been
freed. This patch fix a bug to make sure we don't free it again.
This bug introduced by commit ccb1352e (net: Add Open vSwitch
kernel components.)
Signed-off-by: NAndy Zhou <azhou@nicira.com>
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>

It's slightly smaller/faster for some architectures.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

This patch removes the net_random and net_srandom macros and replaces
them with direct calls to the prandom ones. As new commits only seem to
use prandom_u32 there is no use to keep them around.
This change makes it easier to grep for users of prandom_u32.
Signed-off-by: NAruna-Hewapathirane <aruna.hewapathirane@gmail.com>
Suggested-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In several places 'skb->rxhash = 0' is being done to clear the
rxhash value in an skb.  This does not clear l4_rxhash which could
still be set so that the rxhash wouldn't be recalculated on subsequent
call to skb_get_rxhash.  This patch adds an explict function to clear
all the rxhash related information in the skb properly.

skb_clear_hash_if_not_l4 clears the rxhash only if it is not marked as
l4_rxhash.

Fixed up places where 'skb->rxhash = 0' was being called.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for rewriting SCTP src,dst ports similar to the
functionality already available for TCP/UDP.

Rewriting SCTP ports is expensive due to double-recalculation of the
SCTP checksums; this is performed to ensure that packets traversing OVS
with invalid checksums will continue to the destination with any
checksum corruption intact.
Reviewed-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NJoe Stringer <joe@wand.net.nz>
Signed-off-by: NBen Pfaff <blp@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

Add wildcarded flow support in kernel datapath.

Wildcarded flow can improve OVS flow set up performance by avoid sending
matching new flows to the user space program. The exact performance boost
will largely dependent on wildcarded flow hit rate.

In case all new flows hits wildcard flows, the flow set up rate is
within 5% of that of linux bridge module.

Pravin has made significant contributions to this patch. Including API
clean ups and bug fixes.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NAndy Zhou <azhou@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

It doesn't make sense to output a tunnel packet using the same
parameters that it was received with since that will generally
just result in the packet going back to us. As a result, userspace
assumes that the tunnel key is cleared when transitioning through
the switch. In the majority of cases this doesn't matter since a
packet is either going to a tunnel port (in which the key is
overwritten with new values) or to a non-tunnel port (in which
case the key is ignored). However, it's theoreticaly possible that
userspace could rely on the documented behavior, so this corrects
it.
Signed-off-by: NJesse Gross <jesse@nicira.com>

Add ovs tunnel interface for set tunnel action for userspace.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following patch keeps skb->csum correct across ovs.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In vlan_insert_tag(), we insert a 4-byte VLAN header _after_
mac header:

        memmove(skb->data, skb->data + VLAN_HLEN, 2 * ETH_ALEN);
        ...
        veth->h_vlan_proto = htons(ETH_P_8021Q);
        ...
        veth->h_vlan_TCI = htons(vlan_tci);

so after it, we should recompute the checksum to include these 4 bytes.
skb->data still points to the mac header, therefore VLAN header is at
(2 * ETH_ALEN = 12) bytes after it, not (ETH_HLEN = 14) bytes.

This can also be observed via tcpdump:

         0x0000:  ffff ffff ffff 5254 005d 6f6e 8100 000a
         0x0010:  0806 0001 0800 0604 0001 5254 005d 6f6e
         0x0020:  c0a8 026e 0000 0000 0000 c0a8 0282

Similar for __pop_vlan_tci(), the vlan header we remove is the one
overwritten in:

	memmove(skb->data + VLAN_HLEN, skb->data, 2 * ETH_ALEN);

Therefore the VLAN_HLEN = 4 bytes after 2 * ETH_ALEN is the part
we want to sub from checksum.

Cc: David S. Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

This patch adds support for skb mark matching and set action.
Signed-off-by: NAnsis Atteka <aatteka@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

This patch adds ipv6 set action functionality. It allows to change
traffic class, flow label, hop-limit, ipv6 source and destination
address fields.
Signed-off-by: NAnsis Atteka <aatteka@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

It is a frequent mistake to confuse the netlink port identifier with a
process identifier.  Try to reduce this confusion by renaming fields
that hold port identifiers portid instead of pid.

I have carefully avoided changing the structures exported to
userspace to avoid changing the userspace API.

I have successfully built an allyesconfig kernel with this change.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use hash table to store ports of datapath. Allow 64K ports per switch.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

Signed-off-by: NJoe Stringer <joe@wand.net.nz>
Signed-off-by: NJesse Gross <jesse@nicira.com>

This reverts commit 5b3e7e6c.

The problem that the original commit was attempting to fix can
never happen in practice because validation is done one a per-flow
basis rather than a per-packet basis.  Adding additional checks at
runtime is unnecessary and inconsistent with the rest of the code.

CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If there is no OVS_SAMPLE_ATTR_ACTIONS set then "acts_list" is NULL and
it leads to a NULL dereference when we call nla_len(acts_list).  This
is a static checker fix, not something I have seen in testing.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replaced all instances of Nicira Networks(, Inc) to Nicira, Inc.
Signed-off-by: NRaju Subramanian <rsubramanian@nicira.com>
Signed-off-by: NBen Pfaff <blp@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

When modifying IP addresses or ports on a UDP packet we don't
correctly follow the rules for unchecksummed packets.  This meant
that packets without a checksum can be given a incorrect new checksum
and packets with a checksum can become marked as being unchecksummed.
This fixes it to handle those requirements.
Signed-off-by: NJesse Gross <jesse@nicira.com>

Open vSwitch is a multilayer Ethernet switch targeted at virtualized
environments.  In addition to supporting a variety of features
expected in a traditional hardware switch, it enables fine-grained
programmatic extension and flow-based control of the network.
This control is useful in a wide variety of applications but is
particularly important in multi-server virtualization deployments,
which are often characterized by highly dynamic endpoints and the need
to maintain logical abstractions for multiple tenants.

The Open vSwitch datapath provides an in-kernel fast path for packet
forwarding.  It is complemented by a userspace daemon, ovs-vswitchd,
which is able to accept configuration from a variety of sources and
translate it into packet processing rules.

See http://openvswitch.org for more information and userspace
utilities.
Signed-off-by: NJesse Gross <jesse@nicira.com>