NUM_PORT_STATS was 9 instead of 10, which caused off-by-one bug when
displaying the statistics starting from tx_chksum_offload in ethtool.

Fixes: f8c6455b ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Capture NETDEV events generated by the bonding driver and based on that
make decisions of how to configure port aggregation in the mlx4 core driver.

This includes setting the V2P port table and re-creating the interested
interfaces in bonded/non-bonded mode.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.

The current Ethernet driver code reserves a Tx QP range with 256b alignment.

This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.

This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.

The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:

1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
   and request "BF enabled QPs" if BF is supported for the function

2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0]  - number of QPs
b. param1[31-24] - flags controlling QPs reservation

Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.

Bits 24-30 of the flags are currently reserved.

When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.

In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ConnectX HW is capable of using one of the following hash functions:
Toeplitz and an XOR hash function. This patch extends the implementation
of the mlx4_en driver set/get_rxfh callbacks to support getting and
setting the RSS hash function used by the device.
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4_en_set_rxfh() can crash if no RSS indir table is provided.

While we are at it, allow RSS key to be changed with ethtool -X

Tested:

myhost:~# cat /proc/sys/net/core/netdev_rss_key
b6:89:91:f3:b2:c3:c2:90:11:e8:ce:45:e8:a9:9d:1c:f2:f6:d4:53:61:8b:26:3a:b3:9a:57:97:c3:b6:79:4d:2e:d9:66:5c:72:ed:b6:8e:c5:5d:4d:8c:22:67:30:ab:8a:6e:c3:6a

myhost:~# ethtool -x eth0
RX flow hash indirection table for eth0 with 8 RX ring(s):
    0:      0     1     2     3     4     5     6     7
RSS hash key:
b6:89:91:f3:b2:c3:c2:90:11:e8:ce:45:e8:a9:9d:1c:f2:f6:d4:53:61:8b:26:3a:b3:9a:57:97:c3:b6:79:4d:2e:d9:66:5c:72:ed:b6:8e

myhost:~# ethtool -X eth0 hkey \
03:0e:e2:43:fa:82:0e:73:14:2d:c0:68:21:9e:82:99:b9:84:d0:22:e2:b3:64:9f:4a:af:00:fa:cc:05:b4:4a:17:05:14:73:76:58:bd:2f

myhost:~# ethtool -x eth0
RX flow hash indirection table for eth0 with 8 RX ring(s):
    0:      0     1     2     3     4     5     6     7
RSS hash key:
03:0e:e2:43:fa:82:0e:73:14:2d:c0:68:21:9e:82:99:b9:84:d0:22:e2:b3:64:9f:4a:af:00:fa:cc:05:b4:4a:17:05:14:73:76:58:bd:2f
Reported-by: NBen Hutchings <ben@decadent.org.uk>
Fixes: b9d1ab7e ("mlx4: use netdev_rss_key_fill() helper")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When processing received traffic, pass CHECKSUM_COMPLETE status to the
stack, with calculated checksum for non TCP/UDP packets (such
as GRE or ICMP).

Although the stack expects checksum which doesn't include the pseudo
header, the HW adds it. To address that, we are subtracting the pseudo
header checksum from the checksum value provided by the HW.

In the IPv6 case, we also compute/add the IP header checksum which
is not added by the HW for such packets.

Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: NShani Michaeli <shanim@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When IP_ALIGN has a non zero value, hardware will write to a non aligned
address. The only reader from this address is when copying the header
from the first frag into the linear buffer (further access to the IP
address will be from the linear buffer, in which the headers are
aligned). Since the penalty of non align access by the hardware is
greater than the software memcpy, changing the frag_align to always be 0.
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename mlx4_en_timestamp_config to mlx4_en_reset_config and extend it to support
choosing RX vlan offload configuration.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- If dev cap MLX4_DEV_CAP_FLAG2_ETH_PROT_CTRL is ON, query PTYS register to fill ethtool settings.
else use default values.
- Use autoneg port cap and dev backplane autoneg cap to reprort autoneg interface capbilities.
- Fix typo in mlx4_en_port_state struct field (transciver to transceiver).
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of setting inline threshold using module parameter only on
driver load, use set_tunable() to set it dynamically.
No need to store the threshold per ring, using instead the netdev global
priv->prof->inline_thold
Initial value still is set using the module parameter, therefore
backward compatability is kept.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add frag0_dma/frag0_byte_count into mlx4_en_tx_info to avoid a cache
line miss in TX completion for frames having one dma element.  (We avoid
reading back the tx descriptor)

Note this could be extended to 2/3 dma elements later, as we have free
room in mlx4_en_tx_info

Also, mlx4_en_free_tx_desc() no longer accesses skb_shinfo(). We use a
new nr_maps fields in mlx4_en_tx_info to avoid 2 or 3 cache misses.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- doorbell_qpn is stored in the cpu_to_be32() way to avoid bswap() in fast
  path.
- mdev->mr.key stored in ring->mr_key to also avoid bswap() and access to
  cold cache line.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reorganize struct mlx4_en_tx_ring to have:
- One cache line containing last_nr_txbb & cons & wake_queue, used by tx
  completion.
- One cache line containing fields dirtied by mlx4_en_xmit()
- Following part is read mostly and shared by cpus.

Align struct mlx4_en_tx_info to a cache line
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Remove unused variable ring->poll_cnt
- No need to set some fields if using blueflame
- Add missing const's
- Use unlikely
- Remove unneeded new line
- Make some comments more precise
- struct mlx4_bf @offset field reduced to unsigned int to save space
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethtool -S reports a new counter, tracking number of time doorbell
was not triggered, because skb->xmit_more was set.

$ ethtool -S eth0 | egrep "tx_packet|xmit_more"
     tx_packets: 2413288400
     xmit_more: 666121277

I merged the tso_packet false sharing avoidance in this patch as well.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No caller or macro uses the return value so make it void.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-By: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function derives the base address of the CQE from the CQE size,
and calculates the real CQE context segment in it from the factor
(this is like before). Before this change the code used the factor to
calculate the base address of the CQE as well.

The factor indicates in which segment of the cqe stride the cqe information
is located. For 32-byte strides, the segment is 0, and for 64 byte strides,
the segment is 1 (bytes 32..63). Using the factor was ok as long as we had
only 32 and 64 byte strides. However, with larger strides, the factor is zero,
and so cannot be used to calculate the base of the CQE.

The helper uses the same method of CQE buffer pulling made by all other
components that reads the CQE buffer (mlx4_ib driver and libmlx4).
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When memory is limited, reduce number of rx and tx rings.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the user to turn off the hardware feature called BlueFlame.
Since it is something specific to mlx4_en hardware, we control
the feature via ethtool private flags.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is recommended that TX work not count against the quota.
The cost of TX packet liberation is a minute percentage of what it costs to
process an RX frame. Furthermore, that SKB freeing makes memory available for
other paths in the stack.

Give the TX a larger budget and be more aggressive about cleaning up the Tx
descriptors this budget could be changed using ethtool:
$ ethtool -C eth1 tx-frames-irq <budget>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using a local copy of dev_addr in mlx4_en_set_mac() to prevent dev_addr
from being modified during error flow or when dev_addr is modified in
another context (which is another problem that is being discussed over
the mailing list [1]).
Also fixing bad naming of priv->prev_mac into priv->current_mac.

[1] - http://patchwork.ozlabs.org/patch/351489/Reviewed-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LLC/SNAP 8 bytes should not be added as part of header calculation.
If used, payload will be decreased accordingly. For MTU of 1500
we'll set 1522 instead of 1523.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Reviewed-by: NLiran Liss <liranl@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IRQ affinity notifier can only have a single notifier - cpu_rmap
notifier. Can't use it to track changes in IRQ affinity map.
Detect IRQ affinity changes by comparing CPU to current IRQ affinity map
during NAPI poll thread.

CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2eacc23c ("net/mlx4_core: Enforce irq affinity changes immediatly")
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.

We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it.  To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores.  If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.
Signed-off-by: NYuval Atias <yuvala@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 70a640d0.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.

We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it.  To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores.  If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.
Signed-off-by: NYuval Atias <yuvala@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more current logging style.

o Coalesce formats
o Add missing spaces for coalesced formats
o Align arguments for modified formats
o Add missing newlines for some logging messages
o Use DRV_NAME as part of format instead of %s, DRV_NAME to
  reduce overall text.
o Use ..., ##__VA_ARGS__ instead of args... in macros
o Correct a few format typos
o Use a single line message where appropriate
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-By: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlx4 driver is triggering schedules while atomic inside
mlx4_en_netpoll:

	spin_lock_irqsave(&cq->lock, flags);
	napi_synchronize(&cq->napi);
		^^^^^ msleep here
	mlx4_en_process_rx_cq(dev, cq, 0);
	spin_unlock_irqrestore(&cq->lock, flags);

This was part of a patch by Alexander Guller from Mellanox in 2011,
but it still isn't upstream.
Signed-off-by: NChris Mason <clm@fb.com>
cc: stable@vger.kernel.org
Acked-By: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure that vxlan_get_rx_port() is present in the kernel build in a manner
consistent with mlx4, else mlx4 can be made built-in where vxlan a module and
the phase of the build linking fails. Add CONFIG_MLX4_EN_VXLAN for that.

Also, #ifdef the advertizement and implementation of the mlx4 vxlan ndo
calls and related code under this config directive.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add implementation for the add/del vxlan port ndo calls, using the
CONFIG_DEV firmware command.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the EN driver uses a private static function
mlx4_en_mac_to_u64(). Move it to a common include file (driver.h)
for mlx4_en and mlx4_ib for further use.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Give accurate counters and avoids cache misses when several rings
update the counters of stop/wake queue.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Verify mlx4_en module parameters.
In case they are out of range - reset to default values.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump all Mellanox driver versions.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4_en_add() is too long.
Moving set number of RX rings to a utiltity function to improve
readability and modulization of the code.
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).

This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to use the native GRO handling of encapsulated protocols on
mlx4, we need to call napi_gro_receive() instead of netif_receive_skb()
unless busy polling is in action.

While we are at it, rename mlx4_en_cq_ll_polling() to
mlx4_en_cq_busy_polling()

Tested with GRE tunnel : GRO aggregation is now performed on the
ethernet device instead of being done later on gre device.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Acked-By: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:

- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
  instead of lower device which misses the necessary txq synchronization for
  lower device such as txq stopping or frozen required by dev watchdog or
  control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
  watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
  when tso is disabled for lower device.

Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.

With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.

In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.

Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a PHC to the mlx4_en driver. We use reader/writer spinlocks to
protect the timecounter since every packet received needs to call
timecounter_cycle2time() when timestamping is enabled.  This can become
a performance bottleneck with RSS and multiple receive queues if normal
spinlocks are used.

This driver has been tested with both Documentation/ptp/testptp and the
linuxptp project (http://linuxptp.sourceforge.net/) on a Mellanox
ConnectX-3 card.
Signed-off-by: NShawn Bohrer <sbohrer@rgmadvisors.com>
Acked-By: NHadar Hen Zion <hadarh@mellanox.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the device tunneling offloads mode is vxlan do the following

 - call SET_PORT with the relevant setting

 - add DMFS steering vxlan rule for the device self and multicast mac addresses
   of the form: {<ETH, outer-mac> <VXLAN, ANY vnid> <ETH, ANY mac>} --> RSS QP

 - set relevant QPC fields in RSS context and RX ring QPs

 - in TX flow, set WQE fields to generate HW checksum, and handle gso skbs
   which are marked for encapsulation such that the HW will segment them properly.

 - in RX flow, read HW offloaded checksum for encapsulated packets from the CQE

 - advertize hw_enc_features and NETIF_F_GSO_UDP_TUNNEL to the networking stack
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>