Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

An illegal sequence command error may occur if there is a stopbit or
cmd_index error as well as a CRC error. The correct course of action
is to re-enable IRQs

An illegal sequence data error may occur if there is a CRC or stopbit
error,  or underrun. In this case set data->error correctly.

This is in preparation for enabling tuning support which relies on
differentiating between illegal sequence and other errors.
Signed-off-by: NAi Kyuse <ai.kyuse.uw@renesas.com>
[simon: broken out of a larger patch]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add support for r7s72100 SoC.
Signed-off-by: NChris Brandt <chris.brandt@renesas.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For the r7s72100 SOC, the DATA_PORT register was changed to 32-bits wide.
Therefore a new flag has been created that will allow 32-bit reads/writes
to the DATA_PORT register instead of 16-bit (because 16-bits accesses are
not supported).
Signed-off-by: NChris Brandt <chris.brandt@renesas.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In moving platforms from board files to DT, there still needs to be a way
to set the ocr_mask setting for the tmio driver during probe. Without this
setting, the probe will fail because the supported voltages are not known.

This patch will also traditional platform registration platforms to
migrate to DT.
Signed-off-by: NChris Brandt <chris.brandt@renesas.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There were several instances of code using the
enum mmc_blk_status by arbitrarily converting it to an int and
throwing it around to different functions. This makes the code
hard to understand to may give rise to strange errors.

Especially the function prototype mmc_start_req() had to be
modified to take a pointer to an enum mmc_blk_status and the
function pointer .err_check() inside struct mmc_async_req
needed to return an enum mmc_blk_status.

In every case: instead of assigning the block layer error code
to an int, use the enum, also change the signature of all
functions actually passing this enum to use the enum.

To make it possible to use the enum everywhere applicable, move
it to <linux/mmc/core.h> so that all code actually using it can
also see it.

An interesting case was encountered in the MMC test code which
did not return a enum mmc_blk_status at all in the .err_check
function supposed to check whether asynchronous requests worked
or not: instead it returned a normal -ERROR or even the test
frameworks internal error codes.

The test code would also pass on enum mmc_blk_status codes as
error codes inside the test code instead of converting them
to the local RESULT_* codes.

I have tried to fix all instances properly and run some tests
on the result.

Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The ecc_err flag is only assigned 0 or 1 and treated as a bool,
so convert it to a bool.

Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This gen_err flag is only assigned 0 or 1 and treated as a bool,
so convert it to a bool.

Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The sdhci capabilities register can be incorrect. The sdhci-caps-mask
and sdhci-caps dt properties specify which bits of the register are
incorrect and what their values should be. This patch makes the sdhci
driver use those properties to correct the caps during
__sdhci_read_caps.

During __sdhci_read_caps
Use the sdhci-caps-mask property to turn off the incorrect bits of the
sdhci register after reading them.
Use the sdhci-caps to turn on bits after using sdhci-caps-mask to turn
off the incorrect ones.
Signed-off-by: NZach Brown <zach.brown@ni.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The ST Micro-specific busy detection was made after the assumption
that only this variant supports busy detection. So when doing busy
detection, the host immediately tries to use some ST-specific
register bits.

Since the qualcomm variant also supports some busy detection
schemes, encapsulate the variant flags better in the variant struct
and prepare to add more variants by just providing some bitmasks
to the logic.

Put the entire busy detection logic within an if()-clause in the
mmci_cmd_irq() function so the code is only executed when busy
detection is enabled, and so that it is kept in (almost) one
place, and add comments describing what is going on so the
code can be understood.

Tested on the Ux500 by introducing some prints in the busy
detection path and noticing how the IRQ is enabled, used and
disabled successfully.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There was some confusion in the CPSM (Command Path State Machine)
and DPSM (Data Path State Machine) regarding the naming of the
registers, clarify the meaning of this acronym so the naming is
understandable, and consistently use BIT() to define these fields.

Consequently name the register bit defines MCI_[C|D]PSM_* and
adjust the driver as well.

Include new definitions for a few bits found in a patch from
Srinivas Kandagatla.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Support for DMA slave map has been added to the s3c24xx-dma
controller in commit 34681d84
"dmaengine: s3c24xx: Add dma_slave_map for s3c2440 devices"
This patch converts the s3cmci driver to also use it, so we can
eventually get rid of the exported filter function once all
related DMA clients are updated.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The MMC_CAP2_NO_PRESCAN_POWERUP was invented to avoid running the power up
sequence, mmc_power_up(), during ->probe() of the mmc host driver, but
instead defer this to the mmc detect work. This is especially useful for
those hosts that suffers from a long initialization time, as this time
would otherwise add up to the total boot time.

However, due to the introduction of runtime PM of mmc host devices in the
mmc core, this behaviour changed a bit. More precisely, it caused the mmc
core to runtime resume the host device during ->probe() of the host driver.
In cases like the rtsx_usb_sdmmc, runtime resuming the device may be costly
and thus affecting the total boot time.

To improve this behaviour when using MMC_CAP2_NO_PRESCAN_POWERUP, let's
postpone also calling mmc_power_off() when starting the host. This change
allows the mmc core to avoid runtime resuming the device, as it don't need
to claim the host for that execution path.

Cc: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Initial support for the SD/eMMC controller in the Amlogic S905/GX*
family of SoCs.
Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Now there are no variant drivers using dw_mci_suspend
and dw_mci_resume, so let's remove it.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We could disable biu clk if gpio card detect available,
or it is a non-removable device.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add new helper API mmc_can_gpio_cd for slot-gpio to make
host drivers know whether it supports gpio card detect.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds runtime PM support for dw_mmc-rockchip.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch add dw_mci_runtime_suspend/resume interfaces
and expose it to dw_mci variant driver to support runtime
PM.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When polling for busy after sending a MMC_SWITCH command, both the optional
->card_busy() callback and CMD13 are being used in conjunction.

This doesn't make sense. Instead it's more reasonable to rely solely on the
->card_busy() callback when it exists. Let's change that and instead use
the CMD13 as a fall-back. In this way we avoid sending CMD13, unless it's
really needed.

Within this context, let's also take the opportunity to make some
additional clean-ups and clarifications to the related code.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>

In yet another step of cleaning up __mmc_switch(), let's factor out the
code that deals with card busy polling.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>

The __mmc_switch() deserves a clean-up. In this step, let's move some code
outside of the do-while loop, which deal deals with the card busy polling.

This change simplifies the code in that sense that it becomes easier to follow
what is being executed during card busy polling, but it also gives a better
understanding for when polling isn't done.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>

Following changes needs mmc_switch_status() to be available both from mmc.c
and mmc_ops.c. Allow that by moving its implementation to mmc_ops.c and
make it available via mmc_ops.h.

Moving mmc_switch_status() to mmc_ops.c, also enables us to turn
mmc_switch_status_error() into static function. So let's take the
opportunity to change this as well.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>

Provides runtime PM callbacks to enable and disable clock resources
when idle. Also support system PM callbacks to be called during system
suspend and resume.
Reviewed-by: NRitesh Harjani <riteshh@codeaurora.org>
Reviewed-by: NGeorgi Djakov <georgi.djakov@linaro.org>
Tested-by: NRitesh Harjani <riteshh@codeaurora.org>
Signed-off-by: NPramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

VMMC is an optional regulator, which means that mmc_regulator_get_supply
will only return an error in case of a deferred probe, but not when the
regulator is not set in the DT.

However, the sunxi driver assumes that VMMC is always there, and doesn't
check the value of the regulator pointer before using it, which obviously
leads to a (close to) null pointer dereference.

Add proper checks to prevent that.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/mmc/host/sdhci-of-at91.ko | grep alias
$

After this patch:

$ modinfo drivers/mmc/host/sdhci-of-at91.ko | grep alias
alias:          of:N*T*Catmel,sama5d2-sdhciC*
alias:          of:N*T*Catmel,sama5d2-sdhci
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/mmc/host/mtk-sd.ko | grep alias
$

After this patch:

$ modinfo drivers/mmc/host/mtk-sd.ko | grep alias
alias:          of:N*T*Cmediatek,mt8135-mmcC*
alias:          of:N*T*Cmediatek,mt8135-mmc
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Enable runtime PM autosuspend for the rtsx_usb_sdmmc driver to avoid the
device being runtime suspended and runtime resumed between each request.
Let's use a default timeout of 50ms, to be consistent with other mmc hosts.

Cc: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

value of ios->timing is not related with SDCHI v3.0.  If Controller version
is v3.0, SDHCI_QUIRK_NO_HISPD_BIT is meaningless.  To prevent the setting
wrong bit moves into one condition checking.  (e.g sdhci-s3c doesn't use
SDHCI_CTRL_HISPD bit, instead using this bit as other purpose.)
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When dma->start is failed,then it has to fall back to PIO mode
for current transfer.

But Host controller was already set to bits relevant to DMA operation.
If needs to use the PIO mode, Host controller has to stop the DMA
operation. (It's more stable than now.)

When it occurred error, it's not running any request.

Fixes: 3fc7eaef ("mmc: dw_mmc: Add external dma interface support")
Reported-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since commit 87a18a6a ("mmc: mmc: Use ->card_busy() to detect busy
cards in __mmc_switch()") the ESDHC driver is broken:
  mmc0: Card stuck in programming state! __mmc_switch
  mmc0: error -110 whilst initialising MMC card

Since this commit __mmc_switch() uses ->card_busy(), which is
sdhci_card_busy() for the esdhc driver. sdhci_card_busy() uses the
PRESENT_STATE register, specifically the DAT0 signal level bit. But the
ESDHC uses a non-conformant PRESENT_STATE register, thus a read fixup is
required to make the driver work again.
Signed-off-by: NMichael Walle <michael@walle.cc>
Fixes: 87a18a6a ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()")
Acked-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

An interrupt may occur right after devm_request_irq() is called and
prior to the spinlock initialization, leading to a kernel oops,
as the interrupt handler uses the spinlock.

In order to prevent this problem, move the spinlock initialization
prior to requesting the interrupts.

Fixes: e4243f13 (mmc: mxs-mmc: add mmc host driver for i.MX23/28)
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In the eMMC 4.51 version of the spec, an EXT_CSD field called
GENERIC_CMD6_TIME[248] was added. This allows cards to specify the maximum
time it may need to move out from its busy state, when a CMD6 command has
been sent.

In cases when the card is compliant to versions < 4.51 of the eMMC spec,
obviously the core needs to use a fall-back value for this timeout, which
currently is set to 10 minutes. This value is completely in the wrong range
and importantly in some cases it causes a card initialization to take more
than 10 minute to complete.

Earlier this scenario was avoided as the mmc core used CMD13 to poll the
card, to find out when it stopped signaling busy. Commit 08573eaf
("mmc: mmc: do not use CMD13 to get status after speed mode switch")
changed this behavior.

Instead of reverting that commit, which would cause other issues, let's
instead start by picking a simple solution for the problem, by using a
500ms default generic CMD6 timeout.

The reason for using exactly 500ms, comes from observations that shows it's
quite common for cards to specify 250ms. 500ms is two times that value so
likely it should be enough for most cards.

Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 08573eaf ("mmc: mmc: do not use CMD13 to get status after speed
mode switch")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NStephen Boyd <sboyd@codeaurora.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

mmc_test_check_result_async() requires that struct mmc_async_req is
contained within struct mmc_test_async_req. Fix the "Commands during
non-blocking write" tests so that is the case.

Fixes: 4bbb9aac ("mmc: mmc_test: Add tests for sending commands during transfer")
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Tested-by: NRitesh Harjani <riteshh@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Restore enhanced strobe setting during runtime resume.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

To prevent subsequent commands failing, ensure the cmd and data circuits
are reset after a tuning timeout.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>