This patch (as961) fixes a couple of bugs in the disconnect pathway of
usb-storage.

The first problem, which apparently has been around for a while
although nobody noticed it, shows up when an aborted command is still
pending when a disconnect occurs.  The SCSI error-handler will
continue to wait in command_abort() until the us->notify completion is
signalled.  Thus quiesce_and_remove_host() needs to signal it.

The second problem was introduced recently along with autosuspend
support.  Since usb_stor_scan_thread() now calls
usb_autopm_put_interface() before exiting, we can't simply leave the
scanning thread running after a disconnect; we must wait until the
thread exits.  This is solved by adding a new struct completion to the
private data structure.  Fortuitously, it allows the removal of the
rather clunky mechanism used in the past to insure that all threads
have finished before the module is unloaded.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some devices have a bug which causes them to send a 1-byte reply to
Get-Device-Status requests instead of 2 bytes as required by the
spec.  This doesn't play well with autosuspend, since we look for a
valid status reply to make sure the device is still present when it
resumes.  Without both bytes, we assume the device has been
disconnected.

Lack of the second byte shouldn't matter much, since the spec requires
it always to be equal to 0.  Hence this patch (as959) causes
finish_port_resume() to accept a 1-byte reply as valid.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Hi,

this printer does not survive suspension.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The oti6858 usb serial driver should use kernel_termios_to_user_termios/
user_termios_to_kernel_termios to avoid segfaults because the kernel
uses a structure differing from that of user space with a different
size.
Signed-off-by: NThomas Viehmann <tv@beamnet.de>
CC: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as958) removes an unneeded and unwanted #define line from
dummy_hcd.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If, in em28xx_usb_probe() the memory allocation
	dev->alt_max_pkt_size = kmalloc(32*
						dev->num_alt,GFP_KERNEL);
fails, then we'll bail out and return -ENOMEM.
The problem is that in that case we don't free the storage allocated
to 'dev', thus causing a memory leak.

This patch fixes the leak by freeing 'dev' before we return -ENOMEM.
This fixes Coverity bug #647.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The belkin_sa module has a problem coping with a 0 return from
tty_get_baud_rate() -- the subsequent BELKIN_SA_BAUD macro

drivers/usb/serial/belkin_sa.h:#define BELKIN_SA_BAUD(b) (230400/b)

performs a divide with it leading to the following divide error:

usb 3-1: Belkin / Peracom / GoHubs USB Serial Adapter converter now attached to ttyUSB0
PM: Adding info for No Bus:usbdev3.3_ep81
PM: Adding info for No Bus:usbdev3.3_ep01
PM: Adding info for No Bus:usbdev3.3_ep82
divide error: 0000 [#1]
SMP
Modules linked in: vfat fat iwl3945 mac80211 cfg80211 belkin_sa usbserial usb_storage autofs4 vmnet(P) vmmon(P) aes nf_conntrack_netbios_ns ipt_REJECT nf_conntrack_ipv4 xt_state nf_conntrack nfnetlink xt_tcpudp iptable_filter ip_tables x_tables cpufreq_ondemand acpi_cpufreq video output sbs button dock battery ac arc4 snd_hda_intel ecb blkcipher snd_seq_dummy snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss sr_mod snd_mixer_oss rtc_cmos cdrom iTCO_wdt iTCO_vendor_support snd_pcm rtc_core snd_timer serio_raw b44 ssb rtc_lib parport ata_piix snd soundcore snd_page_alloc mii ata_generic sg ahci libata sd_mod scsi_mod ext3 jbd mbcache ehci_hcd ohci_hcd uhci_hcd
CPU:    1
EIP:    0060:[<f8dd1747>]    Tainted: P        VLI
EFLAGS: 00010246   (2.6.23-rc1 #1)
EIP is at belkin_sa_set_termios+0x18e/0x5b9 [belkin_sa]
eax: 00038400   ebx: 00000000   ecx: 00000000   edx: 00000000
esi: 00038400   edi: 00001cb2   ebp: de49adb0   esp: de49ad6c
ds: 007b   es: 007b   fs: 00d8  gs: 0033  ss: 0068
Process minicom (pid: 7306, ti=de49a000 task=eed6c3b0 task.ti=de49a000)
Stack: d85c74f0 00000046 00000002 00000001 d85c74f0 d85c74f0 00000246 c887c658
       00000001 00000cb0 00000001 00000084 00000000 d01b58c0 f6ba10e0 de49ade8
       de49ae40 de49add0 f8e2526b d85c74b8 ca6e6dbc de49ae40 d85c746c eded72e8
Call Trace:
 [<c0405f35>] show_trace_log_lvl+0x1a/0x2f
 [<c0405fe5>] show_stack_log_lvl+0x9b/0xa3
 [<c04061a5>] show_registers+0x1b8/0x289
 [<c0406389>] die+0x113/0x246
 [<c0622f98>] do_trap+0x8a/0xa3
 [<c04068dc>] do_divide_error+0x85/0x8f
 [<c0622d6a>] error_code+0x72/0x78
 [<f8e2526b>] serial_set_termios+0x86/0x8d [usbserial]
 [<c0542d33>] set_termios+0x309/0x34c
 [<c0542ece>] n_tty_ioctl+0x158/0x4ba
 [<c054030b>] tty_ioctl+0xc78/0xcd6
 [<c048aea0>] do_ioctl+0x50/0x67
 [<c048b100>] vfs_ioctl+0x249/0x25c
 [<c048b15c>] sys_ioctl+0x49/0x61
 [<c0404ed2>] sysenter_past_esp+0x5f/0x99
 =======================
Code: 85 c0 79 14 c7 44 24 04 67 1c dd f8 c7 04 24 d4 1e dd f8 e8 96 99 65 c7 8b 46 04 be 00 84 03 00 e8 47 11 77 c7 31 d2 89 c1 89 f0 <f7> f1 66 85 c0 89 c1 b8 01 00 00 00 0f 44 c8 8b 45 d8 85 db 8b
EIP: [<f8dd1747>] belkin_sa_set_termios+0x18e/0x5b9 [belkin_sa] SS:ESP 0068:de49ad6c

The small patch below should take care of this situation.  Note that my
kernel was tainted (vmware) but the problem will occur if
tty_get_baud_rate() ever returns zero and should be taken care of.
Signed-off-by: NAndy Green <andy@warmcat.com>
Cc: William Greathouse <wgreathouse@smva.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

  The attached (mostly trivial) patches adds support for the Evolution
Scorpion Robots.
  Evolution Robotics supplies a patch against 2.6.8 with their
software. My patch is based on their work, so I don't know if I can
sign it off, or if you need some Evolution people to do this (which
might be hard).
  The patch adds device ID's for some robots which is trivial.



From: Søren Hauberg <hauberg@gmail.com>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Søren

It appears that one reason the "iConnect"-labeled multi-card reader was
on sale for only $5 is that it doesn't handle suspend/resume correctly.
Other than that, it was a good deal for a highspeed MMC/SD bridge.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently when registration fails we're left with a stray reference to
release_mem_region(), this leads to the following case:

    r8a66597_hcd r8a66597_hcd: irq 13, io base 0x18040000
    drivers/usb/host/r8a66597-hcd.c: register access fail.
    r8a66597_hcd r8a66597_hcd: startup error -6
    r8a66597_hcd r8a66597_hcd: USB bus 1 deregistered
    drivers/usb/host/r8a66597-hcd.c: Failed to add hcd
    Trying to free nonexistent resource <0000000018040000-0000000018040000>

This fixes it up.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Previous boards were likely seeing USB_ARCH_HAS_HCD selected by way
of PCMCIA or PCI, though none of those are required for hcd support
on SH. Enable support unconditionally.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Dell Wireless Broadband ExpressCards are rebrands of Novatel's cards.
Add all of their known PCI IDs to date along with their mapping to the exact
Novatel model to the Option driver which already claims to support them.
Signed-off-by: NFaidon Liambotis <paravoid@debian.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I noticed this warning with CONFING_PM=n 

...

drivers/usb/host/u132-hcd.c:1525: warning: 'port_power' defined but not used

...
Signed-off-by: NGabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix typo in safe_serial.c to match the actual CONFIG variable.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes the File Storage Gadget stall the control endpoint
when a MSC class request is made with wValue != 0.  This change makes
some MSC compliance test warnings disappear.
Signed-off-by: NLuis Lloret <luislloret@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch contains two fixes submitted by Ondrej Palkovsky:
- the 'ACK' packet is sent after the transfer of the USB packet is
completed, i.e. in the write_callback function. Because the close
function sends the 'abort' command, a parameter is added that allows
the caller of garmin_write_bulk to specify, if the 'ack' should be
propagated to the serial link or dimissed.
This fixes the problem with gpsbabel, it has sent several packets that
were acknowledged before they were sent to the GPS and GpsBabel closed
the device - thus effectively cancelled all outstanding requests in the
queue.
- removed the APP_RESP_SEEN and APP_REQ_SEEN flags and changed
them into counters. It evades USB reset of the gps on every device close.
Signed-off-by: NHermann Kneissel <hermann.kneissel@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

modprobe visor vendor=0x502 product=0x1
is said to work, plus there are patch instructions for it.
fixes http://bugs.debian.org/340547
see http://www.chinaitpower.com/A/2004-07-28/87909.htmlSigned-off-by: NMaximilian Attems <max@stro.at>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as950) fixes a bug in the cdc-acm driver.  It doesn't keep
track of which interface (control or data) the sysfs attributes get
registered for, and as a result, during disconnect it will sometimes
attempt to remove the attributes from the wrong interface.  The
left-over attributes can cause a crash later on, particularly if the driver
module has been unloaded.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NOliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

git commit b2bbb20b added direct
support for PXA GPIO D+ pullup as alternative to the older udc_command
ops method.  This was done by introduction of the pxa2xx_udc_mach_info
member "gpio_pullup" which, if initialized, is now used in (almost)
all places where udc_command used to be called.

This patch fixes two places where checks for availability of D+ pullup
control still only honor udc_command.
Signed-off-by: NUli Luckas <u.luckas@road.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] Add support for 1533 bridge to alim1535_wdt
  [WATCHDOG] Add a 00-INDEX file to Documentation/watchdog/
  [WATCHDOG] Eurotechwdt.c - clean-up comments

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC32]: Revert f642b263.
  [SPARC64]: Need to clobber global reg vars in switch_to().

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IRDA] irda_nl_get_mode: always results in failure
  [PPP]: Fix output buffer size in ppp_decompress_frame().
  [IRDA]: Avoid a label defined but not used warning in irda_init()
  [IPV6]: Fix kernel panic while send SCTP data with IP fragments
  [SNAP]: Check packet length before reading
  [DCCP]: Allocation in atomic context

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] Change atomic_read/set to inline functions with barrier semantics.
  [S390] kprobes: fix instruction length calculation
  [S390] hypfs: inode corruption due to missing locking
  [S390] disassembler: fix b2 opcodes like srst, bsg, and others
  [S390] vmur: fix reference counting for vmur device structure
  [S390] vmur: fix diag14 exceptions with addresses > 2GB.
  [S390] qdio: Refresh buffer states for IQDIO Asynchronous output queue
  [S390] qdio: fix EQBS handling on CCQ96
  [S390] cio: change confusing message in cmf.
  [S390] cio: dont forget to set last slot to NULL in ccw_uevent().

Touching vmalloc memory in the middle of a lazy mode update can generate
a kernel PDE update, which must be flushed immediately.  The fix is to
leave lazy mode when doing a vmalloc sync.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Acked-by: NJeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After doing some tests this seems to be the best variant for s390 and
should be correct as well. With gcc 4.2.1 we get the following kernel
image sizes using the default configuration:

atomic_t type volatile, atomic_read/set defines   5311824 bytes
atomic_t type int, atomic_read/set defines        5270864 bytes
atomic_t type int, atomic_read/set inline asm     5279056 bytes
atomic_t type int, atomic_read/set inline barrier 5270864 bytes
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Placing a kprobe on "bc" instruction (s390/s390x) can cause an oops.
The instruction length is encoded into the first two bits of the s390
instruction. Kprobe is incorrectly computing the instruction length.
The instruction length is used for determining what type of "fix-up" is
needed for conditional branch instruction. The problem can bee seen by
placing a kprobe on a "bc" instruction that will not branch. The
results is that Kprobe incorrectly computes the new instruction
pointer (psw.addr) after single stepping the instruction. The problem
is corrected with this patch.
Signed-off-by: NDavid Wilder <dwilder@us.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

hypfs removes the whole hypfs directory tree and creates a new one, when a
process triggers an update by writing to the "update" attribute. When removing
and creating files, it is necessary to lock the inode of the parent directory
where the files live. Currently hypfs does not lock the parent inode, which
can lead to inode corruption. This patch:
 * Introduces correct locking
 * Fixes i_nlink reference counting for inodes, when creating directories
 * Adds info printk, when hypfs filesystem has been mounted
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

The instruction table for b2 opcodes was missing an opfrag value
for the cpya instruction. All instructions specified after cpya
were not considered by the disassembler. The fix is simple and
obvious - add the opfrag field to the cpya instruction.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

When a vmur device is removed due to a detach of the device, currently the
ur device structure is freed. Unfortunately it can happen, that there is
still a user of the device structure, when the character device is open
during the detach process. To fix this, reference counting for the vmur
structure is introduced.
In addition to that, the online, offline, probe and remove functions are
serialized now using a global mutex.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

There are several s390 diagnose calls, which must be executed below the
2GB memory boundary. In order to enforce this, those diagnoses must be
compiled into the kernel. Currently diag 14 can be called within the
vmur kernel module from addresses above 2GB. This leads to specification
exceptions. This patch moves diag10, diag14 and diag210 into the new
diag.c file.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Hipersocket Multicast queue works asynchronously. When sending buffers,
the buffer state change may happen delayed. The tasklet for checking
changes in the outbound queue excluded IQDIO async queues from this
process. This created either a hang situation when the queue ran full,
or presented a hang situation a interface close time.
The tasklet processing is changed to include IQDIO async queues when
requesting buffer state refresh.
Signed-off-by: NKlaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

QDIO returned from EQBS instruction in any case after return code
CCQ=96 was issued regardless whether buffer states for at least one
buffer were extracted or not.
This caused FCP devices to hang when running under z/VM and having
QIOASSASIST=ON and having high I/O rates.
In order to fix this qdio return code processing of EQBS instruction
after CCQ=96 is changed that buffers are returned and if no buffers
where extracted the instruction is repeated at once.
Signed-off-by: NKlaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

cmf currently prints a message that more than 4096 channels are not
allowed in basic mode - however, this can only be enforced if cmf was
a module (which is no longer possible). It makes much more sense to
not check the specified number of channels and just print a message if
the block for basic mode could not be allocated (which may happen for
any number of specified channels).
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

It seems an extraneous trailing ';' has slipped in to the error handling for a
name registration failure causing the error path to trigger unconditionally.
Signed-off-by: NAndy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses the issue with "osize too small" errors in mppe
encryption.  The patch fixes the issue with wrong output buffer size
being passed to ppp decompression routine.

--------------------
As pointed out by Suresh Mahalingam, the issue addressed by
ppp-fix-osize-too-small-errors-when-decoding patch is not fully resolved yet.
The size of allocated output buffer is correct, however it size passed to
ppp->rcomp->decompress in ppp_generic.c if wrong. The patch fixes that.
--------------------
Signed-off-by: NKonstantin Sharlaimov <konstantin.sharlaimov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Easily avoidable compiler warnings bug me.

Building irmod without CONFIG_SYSCTL currently results in :
 net/irda/irmod.c:132: warning: label 'out_err_2' defined but not used

But that can easily be avoided by simply moving the label inside
the existing "#ifdef CONFIG_SYSCTL" one line above it.

This patch moves the label and buys us one less warning with no
ill effects.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If ICMP6 message with "Packet Too Big" is received after send SCTP DATA,
kernel panic will occur when SCTP DATA is send again.

This is because of a bad dest address when call to skb_copy_bits().

The messages sequence is like this:

Endpoint A                             Endpoint B
                               <-------  SCTP DATA (size=1432)
ICMP6 message ------->
(Packet Too Big pmtu=1280)
                               <-------  Resend SCTP DATA (size=1432)
------------kernel panic---------------

 printing eip:
c05be62a
*pde = 00000000
Oops: 0002 [#1]
SMP
Modules linked in: scomm l2cap bluetooth ipv6 dm_mirror dm_mod video output sbs battery lp floppy sg i2c_piix4 i2c_core pcnet32 mii button ac parport_pc parport ide_cd cdrom serio_raw mptspi mptscsih mptbase scsi_transport_spi sd_mod scsi_mod ext3 jbd ehci_hcd ohci_hcd uhci_hcd
CPU:    0
EIP:    0060:[<c05be62a>]    Not tainted VLI
EFLAGS: 00010282   (2.6.23-rc2 #1)
EIP is at skb_copy_bits+0x4f/0x1ef
eax: 000004d0   ebx: ce12a980   ecx: 00000134   edx: cfd5a880
esi: c8246858   edi: 00000000   ebp: c0759b14   esp: c0759adc
ds: 007b   es: 007b   fs: 00d8  gs: 0000  ss: 0068
Process swapper (pid: 0, ti=c0759000 task=c06d0340 task.ti=c0713000)
Stack: c0759b88 c0405867 ce12a980 c8bff838 c789c084 00000000 00000028 cfd5a880
       d09f1890 000005dc 0000007b ce12a980 cfd5a880 c8bff838 c0759b88 d09bc521
       000004d0 fffff96c 00000200 00000100 c0759b50 cfd5a880 00000246 c0759bd4
Call Trace:
 [<c0405e1d>] show_trace_log_lvl+0x1a/0x2f
 [<c0405ecd>] show_stack_log_lvl+0x9b/0xa3
 [<c040608d>] show_registers+0x1b8/0x289
 [<c0406271>] die+0x113/0x246
 [<c0625dbc>] do_page_fault+0x4ad/0x57e
 [<c0624642>] error_code+0x72/0x78
 [<d09bc521>] ip6_output+0x8e5/0xab2 [ipv6]
 [<d09bcec1>] ip6_xmit+0x2ea/0x3a3 [ipv6]
 [<d0a3f2ca>] sctp_v6_xmit+0x248/0x253 [sctp]
 [<d0a3c934>] sctp_packet_transmit+0x53f/0x5ae [sctp]
 [<d0a34bf8>] sctp_outq_flush+0x555/0x587 [sctp]
 [<d0a34d3c>] sctp_retransmit+0xf8/0x10f [sctp]
 [<d0a3d183>] sctp_icmp_frag_needed+0x57/0x5b [sctp]
 [<d0a3ece2>] sctp_v6_err+0xcd/0x148 [sctp]
 [<d09cf1ce>] icmpv6_notify+0xe6/0x167 [ipv6]
 [<d09d009a>] icmpv6_rcv+0x7d7/0x849 [ipv6]
 [<d09be240>] ip6_input+0x1dc/0x310 [ipv6]
 [<d09be965>] ipv6_rcv+0x294/0x2df [ipv6]
 [<c05c3789>] netif_receive_skb+0x2d2/0x335
 [<c05c5733>] process_backlog+0x7f/0xd0
 [<c05c58f6>] net_rx_action+0x96/0x17e
 [<c042e722>] __do_softirq+0x64/0xcd
 [<c0406f37>] do_softirq+0x5c/0xac
 =======================
Code: 00 00 29 ca 89 d0 2b 45 e0 89 55 ec 85 c0 7e 35 39 45 08 8b 55 e4 0f 4e 45 08 8b 75 e0 8b 7d dc 89 c1 c1 e9 02 03 b2 a0 00 00 00 <f3> a5 89 c1 83 e1 03 74 02 f3 a4 29 45 08 0f 84 7b 01 00 00 01
EIP: [<c05be62a>] skb_copy_bits+0x4f/0x1ef SS:ESP 0068:c0759adc
Kernel panic - not syncing: Fatal exception in interrupt

Arnaldo says:
====================
Thanks! I'm to blame for this one, problem was introduced in:

b0e380b1

@@ -761,7 +762,7 @@ slow_path:
                /*
                 *      Copy a block of the IP datagram.
                 */
-               if (skb_copy_bits(skb, ptr, frag->h.raw, len))
+               if (skb_copy_bits(skb, ptr, skb_transport_header(skb),
len))
                        BUG();
                left -= len;
====================
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NArnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The snap_rcv code reads 5 bytes so we should make sure that
we have 5 bytes in the head before proceeding.

Based on diagnosis and fix by Evgeniy Polyakov, reported by
Alan J. Wylie.

Patch also kills the skb->sk assignment before kfree_skb
since it's redundant.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>