When the policy for user space is to ignore misaligned accesses from user
space, the processor then performs a documented rotation on the accessed
data.  This is the result of the access being trapped, and the kernel
disabling the alignment trap before returning to user space again.

In kernel space we always want misaligned accesses to be fixed up.  This
is enforced by always re-enabling the alignment trap on every entry into
kernel space from user space.  No such re-enabling is performed when an
exception occurs while already in kernel space as the alignment trap is
always supposed to be enabled in that case.

There is however a small race window when a misaligned access in user
space is trapped and the alignment trap disabled, but the CPU didn't
return to user space just yet.  Any exception would be entered from kernel
space at that point and the kernel would then execute with the alignment
trap disabled.

Thanks to Maxime Bizon <mbizon@freebox.fr> for providing a test module
that made this issue reproducible.
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use a correct udelay value to get bus speed around 100KHz. The udelay
value was most likely copied from the older devices, but the 9g45
is signicantly faster (400MHz, DDR, ..), so a udelay of 2 gives a
bus speed of around 190KHz, which is too fast for some devices.
A udelay value of 5 gives a bus speed of around 90KHz here.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch replace all the lock functions with the irq safe variant.
The ns2_led_{set,get}_mode() functions must be safe in all context.

For example, the trigger timer call led_set_brightness() in a softirq
context.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Signed-off-by: NEric Miao <eric.miao@canonical.com>
Acked-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

When using simultaneously the two DMA channels on a same engine, some
transfers are never completed. For example, an endless lock can occur
while writing heavily on a RAID5 array (with async-tx offload support
enabled).

Note that this issue can also be reproduced by using the DMA test
client.

On a same engine, the interrupt cause register is shared between two
DMA channels. This patch make sure that the cause bit is only cleared
for the requested channel.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Tested-by: NLuc Saillard <luc@saillard.org>
Acked-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

The support for the 2 pcie port of the 6282 has broken i/o port by switching
*_IO_PHYS_BASE and *_IO_BUS_BASE. In fact, the patches reintroduced the same
bug solved by commit 35f029e2.
So, I'm adding back *_IO_BUS_BASE in resource declaration and fix definition
of KIRKWOOD_PCIE1_IO_BUS_BASE. With this change, the xgi card on my t5325 is
working again.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>
Cc: stable@kernel.org

Jonathan Cameron reports that when using the environment
variable KCONFIG_CONFIG, he encounters this error:

make[2]: *** No rule to make target `.config', needed by `arch/arm/boot/compressed/vmlinux.lds'
Reported-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

ARMv7 onwards requires that there are no aliases to the same physical
location using different memory types (i.e. Normal vs Strongly Ordered).
Access to SO mappings when the unaligned accesses are handled in
hardware is also Unpredictable (pgprot_noncached() mappings in user
space).

The /dev/mem driver requires uncached mappings with O_SYNC. The patch
implements the phys_mem_access_prot() function which generates Strongly
Ordered memory attributes if !pfn_valid() (independent of O_SYNC) and
Normal Noncacheable (writecombine) if O_SYNC.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

5cfc8ee0 (ARM: convert arm to arch_gettimeoffset()) marked all of
at91 AND at91x40 as needing ARCH_USES_GETTIMEOFFSET, and hence no high
res timer support / accurate clock_gettime() - But only at91x40 needs it.

Cc: stable@kernel.org
Signed-off-by: NPeter Korsgaard <peter.korsgaard@barco.com>
Acked-by: NJohn Stultz <johnstul@us.ibm.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Setting of these bits can cause issues on other SMP SoC's not produced
by ARM.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Al Viro reports that calling "sys_sigsuspend(-ERESTARTNOHAND, 0, 0)"
with two signals coming and being handled in kernel space results
in the syscall restart being done twice.

Avoid this by clearing the 'why' flag when we call the signal handling
code to prevent further syscall restarts after the first.
Acked-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Clearing bit 22 in the PL310 Auxiliary Control register (shared
attribute override enable) has the side effect of transforming Normal
Shared Non-cacheable reads into Cacheable no-allocate reads.

Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption.

Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On the r2p0, r2p1 and r2p2 versions of the Cortex-A9, data corruption
can occur if a shared cache line is replaced on one CPU as another CPU
is accessing it.

This workaround sets two bits in the diagnostic register of the Cortex-A9,
reducing the linefill issuing capabilities of the processor and
avoiding the erroneous behaviour.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On versions of the Cortex-A9 up to and including r2p2, under rare
circumstances, a DMB instruction between 2 write operations may not
ensure the correct visibility ordering of the 2 writes.

This workaround sets a bit in the diagnostic register of the Cortex-A9,
causing the DMB instruction to behave like a DSB, which functions
correctly on the affected cores.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Kconfig doesn't have any knowledge of specific v7 cores, so it is possible
to select errata workarounds that may cause inadvertent behaviour when
executed on a core other than those targetted by the fix.

This patch improves the variant and revision checking in proc-v7.S so
that the primary part number is also considered when applying errata
workarounds.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We have to use _cansleep gpio accessors in the MMCI driver so as
to avoid slowpath warnings, now U300 has MMCI but doesn't have
these functions in place to siply wrap the existing non-sleeping
functions into sleepable variants.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The prescaler 16 is now used only when the timer runs at 32 MHz
or more. Some comment updates as well.
Acked-by: NAlessandro Rubini <rubini@unipv.it>
Signed-off-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

timer0 to 3 are all on mtu block 0, so don't calculate the clock event
rate based upon mtu block 1's clock speed.
Acked-by: NAlessandro Rubini <rubini@unipv.it>
Signed-off-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: fix potential double put of TCP session reference

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Optimize ticket spinlocks in fsys_rt_sigprocmask

* '2.6.36-fixes' of git://github.com/schandinat/linux-2.6:
  drivers/video/via/ioctl.c: prevent reading uninitialized stack memory

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
  pcmcia pcnet_cs: try setting io_lines to 16 if card setup fails
  pcmcia: per-device, not per-socket debug messages
  pcmcia serial_cs.c: fix multifunction card handling

* git://git.infradead.org/users/cbou/battery-2.6.36:
  apm_power: Add missing break statement
  intel_pmic_battery: Fix battery charging status on mrst

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  watchdog: Enable NXP LPC32XX support in Kconfig (resend)
  watchdog: ts72xx_wdt: disable watchdog at probe
  watchdog: sb_wdog: release irq and reboot notifier in error path and module_exit()

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  arch/tile: fix formatting bug in register dumps
  arch/tile: fix memcpy_fromio()/memcpy_toio() signatures
  arch/tile: Save and restore extra user state for tilegx
  arch/tile: Change struct sigcontext to be more useful
  arch/tile: finish const-ifying sys_execve()

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: wm8350-regulator - fix the logic of checking REGULATOR_MODE_STANDBY mode
  regulator: wm831x-ldo - fix the logic to set REGULATOR_MODE_IDLE and REGULATOR_MODE_STANDBY modes
  regulator: ab8500 - fix off-by-one value range checking for selector
  regulator: 88pm8607 - fix value range checking for accessing info->vol_table
  regulator: isl6271a-regulator - fix regulator_desc parameter for regulator_register()
  regulator: ad5398 - fix a memory leak
  regulator: Update e-mail address for Liam Girdwood
  regulator: set max8998->dev to &pdev->dev.
  regulator: tps6586x-regulator - fix bit_mask parameter for tps6586x_set_bits()
  regulator: tps6586x-regulator - fix value range checking for val
  regulator: max8998 - set max8998->num_regulators
  regulator: max8998 - fix memory allocation size for max8998->rdev
  regulator: tps6507x - remove incorrect comments
  regulator: max1586 - improve the logic of choosing selector
  regulator: ab8500 - fix the logic to remove already registered regulators in error path
  regulator: ab3100 - fix the logic to remove already registered regulators in error path
  regulator/ab8500: move dereference below the check for NULL

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: add documentation

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: only warn on mipmap size checks in r600 cs checker (v2)
  drm/radeon/kms: force legacy pll algo for RV620 LVDS
  drm: fix race between driver loading and userspace open.
  drm: Use a nondestructive mode for output detect when polling (v2)
  drm/radeon/kms: fix the colorbuffer CS checker for r300-r500
  drm/radeon/kms: increase lockup detection interval to 10 sec for r100-r500
  drm/radeon/kms/evergreen: fix backend setup
  drm: Use a nondestructive mode for output detect when polling
  drm/radeon: add some missing copyright headers
  drm: Only decouple the old_fb from the crtc is we call mode_set*
  drm/radeon/kms: don't enable underscan with interlaced modes
  drm/radeon/kms: add connector table for Mac x800
  drm/radeon/kms: fix regression in RMX code (v2)
  drm: Fix regression in disable polling e58f637b

The VIAFB_GET_INFO device ioctl allows unprivileged users to read 246
bytes of uninitialized stack memory, because the "reserved" member of
the viafb_ioctl_info struct declared on the stack is not altered or
zeroed before being copied back to the user.  This patch takes care of
it.
Signed-off-by: NDan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>

Tony's fix (f574c843) has a small bug,
it incorrectly uses "r3" as a scratch register in the first of the two
unlock paths ... it is also inefficient.  Optimize the fast path again.
Signed-off-by: NPetr Tesarik <ptesarik@suse.cz>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The NXP LPC32XX processor use the same watchdog as the Philips
PNX4008 processor.
Signed-off-by: NKevin Wells <wellsk40@gmail.com>
Tested-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Since it may be already enabled by bootloader or some other utility. This patch
makes sure that the watchdog is disabled before any userspace daemon opens the
device. It is also required by the watchdog API.
Signed-off-by: NMika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

irq and reboot notifier are acquired in module_init() but never released.
They should be released correctly, otherwise reloading the module or error
during module_init() will cause a problem.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Andrew Sharp <andy.sharp@lsi.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Some pcnet_cs compatible cards require an exact 16-lines match
of the ioport areas specified in CIS, but set the "iolines"
value in the CIS incorrectly. We can easily work around this
issue -- same as we do in serial_cs -- by first trying setting
iolines to the CIS-specified value, and then trying a 16-line
match.
Reported-and-tested-by: NWolfram Sang <w.sang@pengutronix.de>
Hardware-supplied-by: NJochen Frieling <j.frieling@pengutronix.de>
CC: netdev@vger.kernel.org
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

As the iomem / ioport setup differs per device, it is much better
to print out the device instead of the socket.
Tested-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

We shouldn't overwrite pre-set values, and we should also
set the port address to the beginning, and not the end of
the 8-port range.

CC: linux-serial@vger.kernel.org
Reported-by: NKomuro <komurojun-mbn@nifty.com>
Hardware-supplied-by: NJochen Frieling <j.frieling@pengutronix.de>
Tested-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

This cut-and-paste bug was caused by rewriting the register dump
code to use only a single printk per line of output.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

This tripped up a driver (not yet committed to git).  Fix it now.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

During context switch, save and restore a couple of additional bits of
tilegx user state that can be persistently modified by userspace.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>