Instead of adding "depends on" at config level, introduce HAVE_* config
variables. Add them at machine or soc level to specify the ability of a
particular support.
It will ease new board introduction and readability.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>

Those "depends on" are a double check as all machine entries are
surrounded by "if <ARCH_xxx>" conditions.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>

at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the
previous dual slot board definition to match the official rev. C board. It also
allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one.

Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC
slot A. This lead to a modification of those definitions.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>

* git://git.infradead.org/users/dwmw2/iommu-2.6.32:
  intel-iommu: Support PCIe hot-plug
  intel-iommu: Obey coherent_dma_mask for alloc_coherent on passthrough
  intel-iommu: Check for 'DMAR at zero' BIOS error earlier.

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: SMTC: Fix lockup in smtc_distribute_timer
  MIPS: TXx9: Update rbtx49xx_defconfig
  MIPS: Make local arrays with CL_SIZE static __initdata
  MIPS: Add DMA declare coherent memory support
  MIPS: Fix emulation of 64-bit FPU on FPU-less 64-bit CPUs.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: psmouse - remove unneeded '\n' from psmouse.proto parameter
  Input: atkbd - restore LED state at reconnect
  Input: force LED reset on resume
  Input: fix locking in memoryless force-feedback devices

* 'for-linus' of git://neil.brown.name/md:
  md/raid5: Allow dirty-degraded arrays to be assembled when only party is degraded.
  Don't unconditionally set in_sync on newly added device in raid5_reshape
  md: allow v0.91 metadata to record devices as being active but not in-sync.
  md: factor out updating of 'recovery_offset'.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: restructure pcpu_extend_area_map() to fix bugs and improve readability

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] s390: fix single stepping on svc0
  [S390] sclp: undo quiesce handler override on resume
  [S390] reset cputime accounting after IPL from NSS
  [S390] monreader: fix use after free bug with suspend/resume

If the waker is killed before it can replay outstanding URBs, these URBs
won't be freed or will be replayed at the next open.  This patch closes
the window by explicitely discarding outstanding URBs.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 8177e6d6 ("nfsd: clean up
readdirplus encoding") introduced single character typo in nfs3 readdir+
implementation.  Unfortunately that typo has quite bad side effects:
random memory corruption, followed (on my box) with immediate
spontaneous box reboot.

Using 'p1' instead of 'p' fixes my Linux box rebooting whenever VMware
ESXi box tries to list contents of my home directory.
Signed-off-by: NPetr Vandrovec <petr@vandrovec.name>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

1. At the end of smtc_distribute_timer, nextstamp is valid and has already
   passed so we goto repeat.
2. Nothing updates nextstamp (only updated if the timeout is in the future
   And we just decided it is in the past)
3. At the end nextstamp still has the same value so it is still valid and
   in the past.
4. This repeats until read_c0_count has a value which causes nextstamp to
   be in the future.

Reported and initial patch and testing  by Mikael Starvik
<mikael.starvik@axis.com>.
Signed-off-by: NKevin D. Kissell <kevink@paralogos.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: linux-mips@linux-mips.org
Cc: Jesper Nilsson <Jesper.Nilsson@axis.com>
Patchwork: http://patchwork.linux-mips.org/patch/621/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Enable following features:

  * MTD (RBTX4939, NAND_TXX9NDFMC)
  * HW_RANDOM (HW_RANDOM_TX4939)
  * SOUND (SND_SOC_TXX9ACLC)
  * DMADEVICE (TXX9_DMAC)
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Since commit 22242681 ("MIPS: Extend
COMMAND_LINE_SIZE"), CL_SIZE is 4096 and local array variables with this
size will cause an build failure with default CONFIG_FRAME_WARN settings.

Although current users of such array variables are all early bootstrap
code and not likely to cause real stack overflow (thread_info corruption),
it is preferable to  to declare these arrays static with __initdata.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The ohci-sm501 driver requires dma_declare_coherent_memory().  It is used
by the driver's local memory allocation with dma_alloc_coherent().

Tested on TANBAC TB0287(VR4131 + SM501).

[Ralf: Fixed reject in dma-default.c and removed the entire #if 0'ed block
 in dma-mapping.h instead of just the #if 0.]
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Running a 64-bit kernel on a 64-bit CPU without an FPU would cause the
emulator to run in 32-bit mode.  The c0_Status.FR bit is wired to zero
on systems without an FPU, so using that bit to decide how the emulator
behaves doesn't allow for proper emulation on 64-bit FPU-less
processors.

Instead, we need to select the emulator mode based on the user-space
ABI.  Since the thread flag TIF_32BIT_REGS is used to set c0_Status.FR,
we can just use it to decide if the emulator should be in 32-bit or
64-bit mode.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On s390 there are two ways of specifying the system call number for
the svc instruction. The standard way is to use the immediate field
in the instruction (or to use EXecute for values unknown during
assemble time). This can encode 256 system calls.
The kernel ABI also allows to put the system call number in r1 and
then execute svc 0 to enable system call numbers > 255.

It turns out that single stepping svc 0 is broken, since the PER
program check handler uses r1. We have to use a different register.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

In a system where the ctrl-alt-del init action initiated by signal
quiesce suspends the machine the quiesce handler override for
_machine_restart, _machine_halt and _machine_power_off needs to be
undone, otherwise the override is still present in the resumed
system. The next shutdown would then load the quiesce state psw
instead of performing the correct shutdown action.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

After an IPL from NSS the uptime of the system is incorrect. The reason
is that the startup code in head.S is not executed in case of an IPL
from NSS. Due to that sched_clock_base_cc which is used to initialze
wall_to_monotonic contains the time stamp when the NSS has been created
instead of the time stamp of the system start.

Reinitialize the cputime accounting values in create_kernel_nss after
the SAVESYS CP command that created the NSS segment.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The monreader device driver doesn't set dev->driver_data to NULL after
freeing the corresponding data structure. This leads to a use after
free bug in the freeze/thaw suspend/resume functions after the device
has been opened and closed once. Fix this by clearing dev->driver_data
in the close() function.
Signed-off-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The get parameter function should return a string without a life-feed.
Otherwise you'll see additional empty line in sysfs parameters file.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Even though input core tells us to restore LED state and repeat rate
at resume keyboard may be reconnected either by request from userspace
(via sysfs) or just by pulling it from the box and plugging it back in.
In these cases we still need to restore state ourselves.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

We should be sending EV_LED event down to drivers upon resume even in cases
when in-kernel state of the LED is off since device could come up with some
leds turned on.
Reported-and-tested-by: NMikko Vinni <mmvinni@yahoo.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Normally is it not safe to allow a raid5 that is both dirty and
degraded to be assembled without explicit request from that admin, as
it can cause hidden data corruption.
This is because 'dirty' means that the parity cannot be trusted, and
'degraded' means that the parity needs to be used.

However, if the device that is missing contains only parity, then
there is no issue and assembly can continue.
This particularly applies when a RAID5 is being converted to a RAID6
and there is an unclean shutdown while the conversion is happening.

So check for whether the degraded space only contains parity, and
in that case, allow the assembly.
Signed-off-by: NNeilBrown <neilb@suse.de>

When a reshape finds that it can add spare devices into the array,
those devices might already be 'in_sync' if they are beyond the old
size of the array, or they might not if they are within the array.

The first case happens when we change an N-drive RAID5 to an
N+1-drive RAID5.
The second happens when we convert an N-drive RAID5 to an
N+1-drive RAID6.

So set the flag more carefully.
Also, ->recovery_offset is only meaningful when the flag is clear,
so only set it in that case.

This change needs the preceding two to ensure that the non-in_sync
device doesn't get evicted from the array when it is stopped, in the
case where v0.90 metadata is used.
Signed-off-by: NNeilBrown <neilb@suse.de>

This is a combination that didn't really make sense before.
However when a reshape is converting e.g. raid5 -> raid6, the extra
device is not fully in-sync, but is certainly active and contains
important data.
So allow that start to be meaningful and in particular get
the 'recovery_offset' value (which is needed for any non-in-sync
active device) from the reshape_position.
Signed-off-by: NNeilBrown <neilb@suse.de>

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  omap3: Decrease cpufreq transition latency
  omap3: update Pandora defconfig
  omap3: 3430sdp: Enable Linux Regulator framework
  omap3: beagle: Fix USB host port power control
  omap3: pandora: Fix keypad keymap
  omap1: Amstrad Delta defconfig fixes
  omap: Fix omapfb/lcdc on OMAP1510 broken when PM set
  omap: Use resource_size
  omap: Fix race condition in omap dma driver

pcpu_extend_area_map() had the following two bugs.

* It should return 1 if pcpu_lock was dropped and reacquired but it
  returned 0.  This could lead to oops if free_percpu() races with
  area map extension.

* pcpu_mem_free() was called under pcpu_lock.  pcpu_mem_free() might
  end up calling vfree() which isn't IRQ safe.  This could lead to
  deadlock through lock order inversion via IRQ.

In addition, Linus pointed out that the temporary lock dropping and
subtle three-way return value of pcpu_extend_area_map() was very ugly
and suggested to split the function into two - pcpu_need_to_extend()
and pcpu_extend_area_map().

This patch restructures pcpu_extend_area_map() as suggested and fixes
the two bugs.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>

Because of an integer overflow on start_blk, various kind of wrong results
would be returned by the generic_block_fiemap() handler, such as no
extents when there is a 4GB+ hole at the beginning of the file, or wrong
fe_logical when an extent starts after the first 4GB.
Signed-off-by: NMike Hommey <mh@glandium.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Eric Sandeen <sandeen@sgi.com>
Cc: Josef Bacik <jbacik@redhat.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

PPS events must be recorded according to PPS's mode settings.

If a process asks for (i.e.) capture-assert events only, when the PPS
client calls the pps_event() function to save the current PPS event, we
should verify the event type and then discard unwanted ones.

Also, without this patch userland processes waiting for a specific PPS
event (assert or clear but not both) may be awakened at wrong time.
Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Tested-by: NWilliam S. Brasher <billb958@door.net>
Tested-by: NReg Clemens <clemens@dwf.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Userland programs may read/write PPS parameters at same time and these
operations may corrupt PPS data.
Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Tested-by: NReg Clemens <clemens@dwf.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

TASK_INTERRUPTIBLE and friends are now only available after including
<linux/sched.h>, so include it when needed.

bus_id is no longer available/necessary, so remove that.

Android pmem driver is not available in mainline, so remove its hooks
from drivers/video.
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In case of failure, device_create() returns not NULL but the error code.
The current code checks for non-NULL though which causes kernel oops in
sysfs_create_group() when device_create() fails.  Check for error using
IS_ERR() and propagate the error value using PTR_ERR() instead of fixed
-ENODEV code returned now...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

v3020_mmio_read_bit() always returns 0 when left_shift > 7.

v3020_mmio_read_bit()'s return type is (unsigned char).  The code returns
a value masked by (1 << left_shift) that is casted to the return type.  If
left_shift is larger than 7, the cast will always result in a 0 return
value.  The problem was discovered with left_shift = 16, and the included
patch corrects the problem.

The bug was introduced in the last (Apr 3 2009) commit of the file, kernel
versions 2.6.30 and later.

Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Raphael Assenat <raph@8d.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-vr41xx.c: In function 'vr41xx_rtc_irq_set_freq':
drivers/rtc/rtc-vr41xx.c:217: warning: comparison of distinct pointer types lacks a cast
drivers/rtc/rtc-vr41xx.c:217: warning: right shift count >= width of type
drivers/rtc/rtc-vr41xx.c:217: warning: passing argument 1 of '__div64_32' from incompatible pointer type
include/asm-generic/div64.h:35: note: expected 'uint64_t *' but argument is of type 'long unsigned int *'
Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In setup_arg_pages we work hard to assign a value to ret, but on exit we
always return 0.

Also remove a now duplicated exit path and branch to out_unlock instead.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NSerge Hallyn <serue@us.ibm.com>
Reviewed-by: NWANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The config FB_PRE_INIT_FB entry in drivers/video/Kconfig pushes all entries
below it out of the menuconfig selection. Fix this.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use git.kernel.org not www.kernel.org
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>