Whenever the PAN (P2P) context is active, it
has timers in the uCode that prevent sleep,
so scanning can't be out of channel for more
than the beacon interval programmed into the
device.

Before this patch, a full scan including any
passive channels when P2P was active would
stall forever because it wouldn't find time
to execute the passive requests (for default
beacon intervals of 100 TU.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Led has no use for some platform.
Add additional module parameter option to disable LED
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix multiple bugs in event tracing:

1) If you enable uCode tracing with the device down,
   it will still attempt to access the device and
   continuously log "MAC is in deep sleep!" errors.
   Fix this by only starting logging when the device
   is actually alive.

2) Now you can set the flag when the device is down,
   but logging doesn't happen when you bring it up.
   To fix that, start logging when the device comes
   alive. This means we don't log before -- we could
   do that but I don't need it right now.

3) For some reason we read the error instead of the
   event log -- use the right pointer.

4) Optimise SRAM reading of event log header.

5) Fix reading write pointer == capacity, which can
   happen due to racy SRAM access

6) Most importantly: fix an error where we would try
   to read WAY too many events (like 2^32-300) when
   we read the wrap counter before it is updated by
   the uCode -- this does happen in practice and will
   cause the driver to hang the machine.

7) Finally, change the timer to 10ms instead of 100ms
   as 100ms is too slow to capture all data with a
   normal event log and with 100ms the log will wrap
   multiple times before we have a chance to read it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix few places of typo
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Unted the assumption that the sta struct is still accessible before the
synchronize_rcu call we should move the num_sta_ps counter decrement
after synchronize_rcu to avoid incorrect decrements if num_sta_ps.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Handle MCS masks set by the user.
* Match rates provided by the rate control algorithm to the mask set,
  also in HT mode, and switch back to legacy mode if necessary.
* add debugfs files to observate the rate selection
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow to set mcs masks through nl80211. We also allow to set MCS
rates but no legacy rates (and vice versa).
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Although the rtlwifi family of devices contains 11 copies of the pr_fmt
macro, the macro is not defined for all routines that need it. By moving
the macro to wifi.h, a single copy is available for all routines.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the driver blocked this specific STA with the help of
ieee80211_sta_block_awake we won't clear WLAN_STA_PS_STA later but
still decrement num_sta_ps. Hence, the next data frame from this
STA will trigger ap_sta_ps_end again and also decrement num_sta_ps
again leading to an incorrect num_sta_ps counter.

This can result in problems with powersaving clients not waking up
from PS because the TIM calculation might be skipped due to the
incorrect num_sta_ps counter.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When WLAN_STA_PS_DRIVER is set by ieee80211_sta_block_awake the
num_sta_ps counter is not incremented. Hence, we shouldn't decrement
it in __sta_info_destroy if only WLAN_STA_PS_DRIVER is set. This
could result in an incorrect num_sta_ps counter leading to strange side
effects with associated powersaving clients.

Fix this by only decrementing num_sta_ps when WLAN_STA_PS_STA was set
before.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the future, when we start notifying drivers,
state transitions could potentially fail. To make
it easier to distinguish between programming bugs
and driver failures:
 * rename sta_info_move_state() to
   sta_info_pre_move_state() which can only be
   called before the station is inserted (and
   check this with a new station flag).
 * rename sta_info_move_state_checked() to just
   plain sta_info_move_state(), as it will be
   the regular function that can fail for more
   than just one reason (bad transition or an
   error from the driver)

This makes the programming model easier -- one of
the functions can only be called before insertion
and can't fail, the other can fail.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit f1e3be15.

Johannes Berg <johannes@sipsolutions.net> thinks that this patch is
incorrect.  I'll defer to his judgment.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The device seems to survive the issue, so no need to flood the logs
about it...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While configuring the broadcast key in the hardware, in
multi-BSS environment, BSSes other than first were
incorrectly configured with the MAC address of first
BSS. Fixing it with correct MAC addresses.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, when we are on an IBSS network with no active station,
we would scan for other BSSID, even if fixed_bssid is on,  due to
a bug in ibss.c,  where fixed_channel would be checked instead of
fixed_bssid.  This would trigger useless scans where scan results
would not be used anyway.

This patch also reverts commit 39d02a7d,
which assumed that the ifibss->fixed_channel check was legitimate
to disable single-channel scans.  IBSS single-channel scan should
now be fixed.
Signed-off-by: NNicolas Cavallari <cavallar@lri.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sta might be in psm against the ap (e.g. because
this was the before a hw restart), so we explicitly
send a null packet in order to make sure it'll
sync against the ap (and get out of psm).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a pointer so it should be NULL instead of zero.  Sparse
complains about this stuff:
net/nfc/nci/core.c:447:37: warning: Using plain integer as NULL pointer
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This enables user to check beacon interval, DTIM period, short slot
time and short preamble information using "iw dev mlan0 link" command
when station is in connected state.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Pass mwifiex_private pointer directly to wmm_add_buf_txqueue()
instead of passing adapter and then deriving priv again in
mwifiex_get_priv_by_id(). This reduces a 'for' loop in TX path.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This seems to be only needed as workaround for hardware problem on
PCI devices.
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Zero all other bits than RESET_CSR and RESET_BBP when want to do the
reset, that the vendor driver behaviour.
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can receive frames just after firmware load with current code, so
disable DMA just after firmware is loaded, not before.
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ralink USB driver initialize H2M_INT_SRC to 0 after firmware load, and
never touch this register later. It is not touched at all by Ralink PCI
driver.
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix new kernel-doc warnings:

Warning(include/net/cfg80211.h:1165): No description found for parameter 'channel_type'
Warning(include/net/cfg80211.h:2090): No description found for parameter 'probe_resp_offload'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc:	Johannes Berg <johannes@sipsolutions.net>
Cc:	linux-wireless@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch implements a simple way of reducing the
output power of the device by a configurable upper
limit.
Requested-by: NHarshal Chhaya <harshal@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to firmware limitations, we may not be able to
support beacon filtering on all virtual interfaces.
To allow this in mac80211, introduce per-interface
driver capability flags that the driver sets when
an interface is added.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Avoids this:

  CC [M]  drivers/net/wireless/orinoco/orinoco_usb.o
drivers/net/wireless/orinoco/orinoco_usb.c:1759:13: warning: ‘version’ defined but not used
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Avoids this:

  CC [M]  drivers/net/wireless/ath/ath5k/base.o
drivers/net/wireless/ath/ath5k/base.c: In function ‘__check_no_hw_rfkill_switch’:
drivers/net/wireless/ath/ath5k/base.c:85:1: warning: return from incompatible pointer type
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Skip group keys configuration in hardware in order to make IBSS RSN work.
Keys will be managed using software.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the ability to select between multiple targets in NCI.
If only one target is found, it will be auto-activated.
If more than one target is found, then DISCOVER_NTF will be
generated for each target, and the host should select one by
calling DISCOVER_SELECT_CMD. Then, the target will be activated.
If the activation fails, GENERIC_ERROR_NTF is generated.
Signed-off-by: NIlan Elias <ilane@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The NFC core layer should not set the target_idx.
Instead, the driver layer (e.g. NCI, PN533) should set the
target_idx, so that it will be able to identify the target
when its I/F (e.g. activate_target) is called.
This is required in order to support multiple targets.
Note that currently supported drivers (PN533 and NCI) don't
use the target_idx in their implementation.
Signed-off-by: NIlan Elias <ilane@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make a clear separation between NCI states and flags.
This is required in order to support more NCI states (e.g.
for multiple targets support).
Signed-off-by: NIlan Elias <ilane@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In case of a node re-joining the cell the sta_info structure belonging to it is
first destroyed and then reinserted. In this way its internal state is reset.

The joining operation is recognised thank the Auth frame being received.

This operation is helpful in case of a node being rebooted that is joining the
ad-hoc cell again, before its purge timeout on other nodes expires.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In IBSS mode, whenever a new station is added a 2-way authentication challenge
is performed. Actually this event can be used to recognise a new station joining
the cell even if its sta_info entry is already in the list.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Free sk_buff if nfcwilink_send fails.
Signed-off-by: NIlan Elias <ilane@ti.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Download TI NFC init script during nfcwilink open operation,
after the NFC channel is registered with TI shared transport.
TI NFC init script is written in BTS format.
First, read the chip version via a special vendor specific command.
Second, we request the relevant BTS file from the user space, and
then send the BTS commands to the chip.
Signed-off-by: NIlan Elias <ilane@ti.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>