The following code is defined but never used.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

MMIO log traces obtained using the Broadcom wl hybrid driver show that
the RETRY_TIMEOUT register (0x41) in PCI configuration space is cleared
if non-zero. Similar code found in other drivers such as ipw2100 show
this operation is needed to keep PCI Tx retries from interfering with
C3 CPU state. There are no known cases where omission of this code has
caused a problem, but this patch is offered just in case such a situation
occurs.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes this sparse warning:

  CHECK   drivers/net/wireless/ath/ath5k/base.c
drivers/net/wireless/ath/ath5k/base.c:569:6: warning: symbol
'ath5k_update_bssid_mask_and_opmode' was not declared. Should it be static?
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes this sparse warning:

  CHECK   drivers/net/wireless/ath/key.c
drivers/net/wireless/ath/key.c:110:6: warning: symbol
'ath_hw_set_keycache_entry' was not declared. Should it be static?
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes this sparse warning:

  CHECK   drivers/net/wireless/ath/key.c
drivers/net/wireless/ath/key.c:70:6: warning: symbol 'ath_hw_keysetmac' was not declared. Should it be static?
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_hw_set_txpowerlimit gets an extra boolean parameter that - if set -
causes the rate txpower table and the regulatory limit to be calculated
and stored, without changing hardware registers.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The same is done for the older chip families as well.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Include the channel utilization (busy, rx, tx) in the survey results.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Similar to Felix Fietkau <nbd@openwrt.org> "ath9k_hw: optimize all descriptor
access functions" (13db2a80244908833502189a24de82a856668b8a).
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the current rate control selection method the median function is
nowhere used, so remove it.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Because all of the descriptor data structures are marked as __packed, GCC
assumes the worst case wrt. alignment and generates unaligned load/store
instructions on MIPS for access to all fields.
Since descriptors always have to be 4-byte-aligned, we can just mark the
data structures with __aligned(4), which allows GCC to generate much more
efficient code.
Verified through disassembly and OProfile comparisons.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k driver uses the legacy PCI power management (suspend
and resume) callbacks that apparently cause intermittent problems
to happen (the adapter sometimes doesn't resume correctly on my
Acer Ferrari One).  Make it use the new PCI PM and let the PCI core
code handle the PCI-specific details of power transitions.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes this sparse complaint:

  CHECK   drivers/net/wireless/ath/ath9k/debug.c
drivers/net/wireless/ath/ath9k/debug.c:548:34: warning: symbol 'aphy' shadows an earlier one
drivers/net/wireless/ath/ath9k/debug.c:491:26: originally declared here
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is now only used in hw.c
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the timer_next argument to ath9k_gen_timer_start is behind the tsf value,
tsf + timer_period is used, which is what ath_btcoex_period_timer was setting
it to.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ANI needs the RSSI average only in station mode, and only for tracking
the signal strength of beacons of the AP that it is connected to.
Adjust the code to track on the beacon RSSI, and store the average of that
in the ath_wiphy struct.
With these changes, we can get rid of this extra station lookup in the
rx path, which saves precious CPU cycles.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Disassembly shows, that at least on MIPS, the compiler generates a lot of
memory accesses to the same location in the descriptor field parsing.
Since it is operating on uncached memory, this can be quite expensive in
this hot path.
Change the code a bit to help the compiler optimize it properly, and get
rid of some unused fields in the ath_tx_status struct.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ah->config.rx_intr_mitigation does not need to be checked before checking
the rx interrupt mask for AR_ISR_RXMINTR or AR_ISR_RXINTM, as those
interrupts will be masked out if rx interrupt mitigation is disabled.

Avoid reading AR_ISR_S5_S twice by reordering the code to be more concise.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

OProfile showed that ath9k was spending way too much time in
ath9k_hw_set_interrupts. Since most of the interrupt mask changes only
need to globally enable/disable interrupts, it makes sense to split
this part into separate functions, replacing all calls to
ath9k_hw_set_interrupts(ah, 0) with ath9k_hw_disable_interrupts(ah).

ath9k_hw_set_interrupts(ah, ah->imask) only gets changed to
ath9k_hw_enable_interrupts(ah), whenever ah->imask was not changed
since the point where interrupts were disabled.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: Henry Ptasinski <henryp@broadcom.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Nohee Ko <noheek@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: Henry Ptasinski <henryp@broadcom.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Nohee Ko <noheek@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* 'for-linus' of git://www.jni.nu/cris:
  CRIS: Add paths for CRISv10 serial driver
  CRIS: Fix RS485 delay handling.
  Add missing "struct" to in sizeof.

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
  spi/pl022: fix erroneous platform data in U300
  spi: fixed odd static string conventions in core code
  spi/bfin_spi: only request GPIO on first load
  spi/bfin_spi: handle error/status changes after data interrupts
  spi: enable spi_board_info to be registered after spi_master

Signed-off-by: NJesper Nilsson <jesper.nilsson@axis.com>

This fixes an erroneous use of LSB first in the U300 machine, the
PL022 used in U300 is a standard ARM core that doesn't support this
bit so it should never have been set.

Cc: Kevin Wells <wellsk40@gmail.com>OA
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

We were forgetting to set up proper return value in success path causing
ir_getkeycode() to fail intermittently:

drivers/media/IR/ir-keytable.c: In function 'ir_getkeycode':
drivers/media/IR/ir-keytable.c:363: warning: 'retval' may be used
uninitialized in this function
Reported-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c-i801: Add PCI idents for Patsburg 'IDF' SMBus controllers
  i2c-i801: Handle multiple instances instead of keeping global state
  i2c-i801: Add Intel Patsburg device ID
  i2c: Drop unused I2C_CLASS_TV flags

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: appletouch - remove extra KERN_DEBUG use from dprintk
  Input: bu21013_ts - fix null dereference in error handling
  Input: ad7879 - prevent invalid finger data reports

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (70 commits)
  [SCSI] pmcraid: add support for set timestamp command and other fixes
  [SCSI] pmcraid: remove duplicate struct member
  [SCSI] qla4xxx: Fix cmd check in qla4xxx_cmd_wait
  [SCSI] megaraid_sas: Version and documentation update
  [SCSI] megaraid_sas: Add three times Online controller reset
  [SCSI] megaraid_sas: Add input parameter for max_sectors
  [SCSI] megaraid_sas: support devices update flag
  [SCSI] libosd: write/read_sg_kern API
  [SCSI] libosd: Support for scatter gather write/read commands
  [SCSI] libosd: Free resources in reverse order of allocation
  [SCSI] libosd: Fix bug in attr_page handling
  [SCSI] lpfc 8.3.18: Update lpfc driver version to 8.3.18
  [SCSI] lpfc 8.3.18: Add new WQE support
  [SCSI] lpfc 8.3.18: Fix critical errors
  [SCSI] lpfc 8.3.18: Adapter Shutdown and Unregistration cleanup
  [SCSI] lpfc 8.3.18: Add logic to detect last devloss timeout
  [SCSI] lpfc 8.3.18: Add support of received ELS commands
  [SCSI] lpfc 8.3.18: FC/FCoE Discovery fixes
  [SCSI] ipr: add definitions for a new adapter
  [SCSI] bfa: fix comments for c files
  ...

Merge branches 'irq-core-for-linus' and 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Fix up irq_node() for irq_data changes.
  genirq: Add single IRQ reservation helper
  genirq: Warn if enable_irq is called before irq is set up

* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  semaphore: Remove mutex emulation
  staging: Final semaphore cleanup
  jbd2: Convert jbd2_slab_create_sem to mutex
  hpfs: Convert sbi->hpfs_creation_de to mutex

Fix up trivial change/delete conflicts with deleted 'dream' drivers
(drivers/staging/dream/camera/{mt9d112.c,mt9p012_fox.c,mt9t013.c,s5k3e2fx.c})

These are the extra 'Integrated Device Function' SMBus controllers found
on the Patsburg chipset. Mention the absence of slave mode support.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

It's poor form to keep driver state in global variables rather than
per-instance. It never really mattered in practice when there was only
one controller on the chipset, but the latest chipsets do have more
than one controller, so now we care.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add support for the Intel Patsburg PCH SMBus Controller.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

There are no users left for I2C_CLASS_TV_ANALOG and
I2C_CLASS_TV_DIGITAL, so we can get rid of them.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This one was only used for a nasty hack in nfsd, which has recently
been removed.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The caller allocated it, the caller should free it.

The only issue so far is that we could change the flp pointer even on an
error return if the fl_change callback failed.  But we can simply move
the flp assignment after the fl_change invocation, as the callers don't
care about the flp return value if the setlease call failed.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>