The svm_dev_ops has never been referenced in the tree, and there's no
plan to have anything to use it. Remove it to make the code neat.
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210323010600.678627-3-baolu.lu@linux.intel.comSigned-off-by: NJoerg Roedel <jroedel@suse.de>

The VT-d specification (section 7.6) requires that the value in the
Private Data field of a Page Group Response Descriptor must match
the value in the Private Data field of the respective Page Request
Descriptor.

The private data field of a page group response descriptor is set then
immediately cleared in prq_event_thread(). This breaks the rule defined
by the VT-d specification. Fix it by moving clearing code up.

Fixes: 5b438f4b ("iommu/vt-d: Support page request in scalable mode")
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: NLiu Yi L <yi.l.liu@intel.com>
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210320024156.640798-1-baolu.lu@linux.intel.comSigned-off-by: NJoerg Roedel <jroedel@suse.de>

The pasid_lock is used to synchronize different threads from modifying a
same pasid directory entry at the same time. It causes below lockdep splat.

[   83.296538] ========================================================
[   83.296538] WARNING: possible irq lock inversion dependency detected
[   83.296539] 5.12.0-rc3+ #25 Tainted: G        W
[   83.296539] --------------------------------------------------------
[   83.296540] bash/780 just changed the state of lock:
[   83.296540] ffffffff82b29c98 (device_domain_lock){..-.}-{2:2}, at:
           iommu_flush_dev_iotlb.part.0+0x32/0x110
[   83.296547] but this lock took another, SOFTIRQ-unsafe lock in the past:
[   83.296547]  (pasid_lock){+.+.}-{2:2}
[   83.296548]

           and interrupts could create inverse lock ordering between them.

[   83.296549] other info that might help us debug this:
[   83.296549] Chain exists of:
                 device_domain_lock --> &iommu->lock --> pasid_lock
[   83.296551]  Possible interrupt unsafe locking scenario:

[   83.296551]        CPU0                    CPU1
[   83.296552]        ----                    ----
[   83.296552]   lock(pasid_lock);
[   83.296553]                                local_irq_disable();
[   83.296553]                                lock(device_domain_lock);
[   83.296554]                                lock(&iommu->lock);
[   83.296554]   <Interrupt>
[   83.296554]     lock(device_domain_lock);
[   83.296555]
                *** DEADLOCK ***

Fix it by replacing the pasid_lock with an atomic exchange operation.
Reported-and-tested-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210320020916.640115-1-baolu.lu@linux.intel.comSigned-off-by: NJoerg Roedel <jroedel@suse.de>

Page requests are originated from the user page fault. Therefore, we
shall set FAULT_FLAG_USER. 

FAULT_FLAG_REMOTE indicates that we are walking an mm which is not
guaranteed to be the same as the current->mm and should not be subject
to protection key enforcement. Therefore, we should set FAULT_FLAG_REMOTE
to avoid faults when both SVM and PKEY are used.

References: commit 1b2ee126 ("mm/core: Do not enforce PKEY permissions on remote mm access")
Reviewed-by: NRaj Ashok <ashok.raj@intel.com>
Acked-by: NLu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Link: https://lore.kernel.org/r/1614680040-1989-5-git-send-email-jacob.jun.pan@linux.intel.comSigned-off-by: NJoerg Roedel <jroedel@suse.de>

When supervisor/privilige mode SVM is used, we bind init_mm.pgd with
a supervisor PASID. There should not be any page fault for init_mm.
Execution request with DMA read is also not supported.

This patch checks PRQ descriptor for both unsupported configurations,
reject them both with invalid responses.

Fixes: 1c4f88b7 ("iommu/vt-d: Shared virtual address in scalable mode")
Acked-by: NLu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Link: https://lore.kernel.org/r/1614680040-1989-4-git-send-email-jacob.jun.pan@linux.intel.comSigned-off-by: NJoerg Roedel <jroedel@suse.de>

Write protect bit, when set, inhibits supervisor writes to the read-only
pages. In guest supervisor shared virtual addressing (SVA), write-protect
should be honored upon guest bind supervisor PASID request.

This patch extends the VT-d portion of the IOMMU UAPI to include WP bit.
WPE bit of the  supervisor PASID entry will be set to match CPU CR0.WP bit.
Signed-off-by: NSanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: NLu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/1614680040-1989-3-git-send-email-jacob.jun.pan@linux.intel.comSigned-off-by: NJoerg Roedel <jroedel@suse.de>

Write protect bit, when set, inhibits supervisor writes to the read-only
pages. In supervisor shared virtual addressing (SVA), where page tables
are shared between CPU and DMA, IOMMU PASID entry WPE bit should match
CR0.WP bit in the CPU.
This patch sets WPE bit for supervisor PASIDs if CR0.WP is set.
Signed-off-by: NSanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: NLu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/1614680040-1989-2-git-send-email-jacob.jun.pan@linux.intel.comSigned-off-by: NJoerg Roedel <jroedel@suse.de>

When the invalidation queue errors are encountered, dump the information
logged by the VT-d hardware together with the pending queue invalidation
descriptors.
Signed-off-by: NAshok Raj <ashok.raj@intel.com>
Tested-by: NGuo Kaijie <Kaijie.Guo@intel.com>
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210318005340.187311-1-baolu.lu@linux.intel.comSigned-off-by: NJoerg Roedel <jroedel@suse.de>

Currently, the Intel VT-d supports Shared Virtual Memory (SVM) only when
IO page fault is supported. Otherwise, shared memory pages can not be
swapped out and need to be pinned. The device needs the Address Translation
Service (ATS), Page Request Interface (PRI) and Process Address Space
Identifier (PASID) capabilities to be enabled to support IO page fault.

Disable SVM when ATS, PRI and PASID are not enabled in the device.
Signed-off-by: NKyung Min Park <kyung.min.park@intel.com>
Acked-by: NLu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210314201534.918-1-kyung.min.park@intel.comSigned-off-by: NJoerg Roedel <jroedel@suse.de>

commit 0d835962 ("zram: support page writeback") introduced two
problems.  It overwrites writeback_store's return value as kstrtol's
return value, which makes return value zero so user could see zero as
return value of write syscall even though it wrote data successfully.

It also breaks index value in the loop in that it doesn't increase the
index any longer.  It means it can write only first starting block index
so user couldn't write all idle pages in the zram so lose memory saving
chance.

This patch fixes those issues.

Link: https://lkml.kernel.org/r/20210312173949.2197662-2-minchan@kernel.org
Fixes: 0d835962("zram: support page writeback")
Signed-off-by: NMinchan Kim <minchan@kernel.org>
Reported-by: NAmos Bianchi <amosbianchi@google.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: John Dias <joaodias@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

writeback_store's return value is overwritten by submit_bio_wait's return
value.  Thus, writeback_store will return zero since there was no IO
error.  In the end, write syscall from userspace will see the zero as
return value, which could make the process stall to keep trying the write
until it will succeed.

Link: https://lkml.kernel.org/r/20210312173949.2197662-1-minchan@kernel.org
Fixes: 3b82a051("drivers/block/zram/zram_drv.c: fix error return codes not being returned in writeback_store")
Signed-off-by: NMinchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: John Dias <joaodias@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After is_cow_mapping() is exported in mm.h, replace some manual checks
elsewhere throughout the tree but start to use the new helper.

Link: https://lkml.kernel.org/r/20210217233547.93892-5-peterx@redhat.comSigned-off-by: NPeter Xu <peterx@redhat.com>
Reviewed-by: NJason Gunthorpe <jgg@ziepe.ca>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Roland Scheidegger <sroland@vmware.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Gal Pressman <galpress@amazon.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jann Horn <jannh@google.com>
Cc: Kirill Shutemov <kirill@shutemov.name>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Wei Zhang <wzam@amazon.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ns can be NULL at this point, and my move of the check from
the original patch by Chaitanya broke this.

Fixes: 0ec84df4 ("nvme-core: check ctrl css before setting up zns")
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.

Fixes: 53c218da ("driver/perf: Add PMU driver for the ARM DMC-620 memory controller")
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210312080421.277562-1-weiyongjun1@huawei.comSigned-off-by: NWill Deacon <will@kernel.org>

We are required to call dev_pm_opp_put() from outside of the
opp_table->lock as debugfs removal needs to happen lock-less to avoid
circular dependency issues.

commit cf1fac94 ("opp: Reduce the size of critical section in
_opp_kref_release()") tried to fix that introducing a new routine
_opp_get_next() which keeps returning OPPs that can be freed by the
callers and this routine shall be called without holding the
opp_table->lock.

Though the commit overlooked the fact that the OPPs can be referenced by
other users as well and this routine will end up dropping references
which were taken by other users and hence freeing the OPPs prematurely.

In effect, other users of the OPPs will end up having invalid pointers
at hand. We didn't see any crash reports earlier as the exact situation
never happened, though it is certainly possible.

We need a way to mark which OPPs are no longer referenced by the OPP
core, so we don't drop extra references to them accidentally.

This commit adds another OPP flag, "removed", which is used to track
this. And now we should never end up dropping extra references to the
OPPs.

Cc: v5.11+ <stable@vger.kernel.org> # v5.11+
Fixes: cf1fac94 ("opp: Reduce the size of critical section in _opp_kref_release()")
Signed-off-by: NBeata Michalska <beata.michalska@arm.com>
[ Viresh: Almost rewrote entire patch, added new "removed" field,
	  rewrote commit log and added the correct Fixes tag. ]
Co-developed-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>

The index variable should only be increased in one place.

Noticed this while trying to track down another oops.

v2: use while loop.

Fixes: f295c8cf ("drm/nouveau: fix dma syncing warning with debugging on.")
Signed-off-by: NDave Airlie <airlied@redhat.com>
Reviewed-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210311043527.5376-1-airlied@gmail.com

Commit 311a50e7 ("drm/i915: Add support for mandatory cmdparsing")
introduced mandatory command parsing but setup failures were not
translated into wedging the GPU which was probably the intent.

Possible errors come in two categories. Either the sanity check on
internal tables has failed, which should be caught in CI unless an
affected platform would be missed in testing; or memory allocation failure
happened during driver load, which should be extremely unlikely but for
correctness should still be handled.

v2:
 * Tidy coding style. (Chris)

[airlied: cherry-picked to avoid rc1 base]
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 311a50e7 ("drm/i915: Add support for mandatory cmdparsing")
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Reviewed-by: NChris Wilson <chris.p.wilson@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210302114213.1102223-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 5a1a659762d35a6dc51047c9127c011303c77b7f)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Ever since the addition of multipage bio_vecs BIO_MAX_PAGES has been
horribly confusingly misnamed.  Rename it to BIO_MAX_VECS to stop
confusing users of the bio API.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20210311110137.1132391-2-hch@lst.deSigned-off-by: NJens Axboe <axboe@kernel.dk>

The valid selector is 0 ~ 0xbf, so the .n_voltages should be 0xc0.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210311020558.579597-1-axel.lin@ingics.comSigned-off-by: NMark Brown <broonie@kernel.org>

If port terminations are detected in suspend, but link never reaches U0
then xHCI may have an internal uncleared wake state that will cause an
immediate wake after suspend.

This wake state is normally cleared when driver clears the PORT_CSC bit,
which is set after a device is enabled and in U0.

Write 1 to clear PORT_CSC for ports that don't have anything connected
when suspending. This makes sure any pending internal wake states in
xHCI are cleared.

Cc: stable@vger.kernel.org
Tested-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-5-mathias.nyman@linux.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

I've confirmed that both the ASMedia ASM1042A and ASM3242 have the same
problem as the ASM1142 and ASM2142/ASM3142, where they lose some of the
upper bits of 64-bit DMA addresses. As with the other chips, this can
cause problems on systems where the upper bits matter, and adding the
XHCI_NO_64BIT_SUPPORT quirk completely fixes the issue.

Cc: stable@vger.kernel.org
Signed-off-by: NForest Crossman <cyrozap@gmail.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-4-mathias.nyman@linux.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A xHC USB 3 port might miss the first wake signal from a USB 3 device
if the port LFPS reveiver isn't enabled fast enough after xHC resume.

xHC host will anyway be resumed by a PME# signal, but will go back to
suspend if no port activity is seen.
The device resends the U3 LFPS wake signal after a 100ms delay, but
by then host is already suspended, starting all over from the
beginning of this issue.

USB 3 specs say U3 wake LFPS signal is sent for max 10ms, then device
needs to delay 100ms before resending the wake.

Don't suspend immediately if port activity isn't detected in resume.
Instead add a retry. If there is no port activity then delay for 120ms,
and re-check for port activity.

Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-3-mathias.nyman@linux.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On some systems rt2800usb and mt7601u devices are unable to operate since
commit f8f80be5 ("xhci: Use soft retry to recover faster from
transaction errors")

Seems that some xHCI controllers can not perform Soft Retry correctly,
affecting those devices.

To avoid the problem add xhci->quirks flag that restore pre soft retry
xhci behaviour for affected xHCI controllers. Currently those are
AMD_PROMONTORYA_4 and AMD_PROMONTORYA_2, since it was confirmed
by the users: on those xHCI hosts issue happen and is gone after
disabling Soft Retry.

[minor commit message rewording for checkpatch -Mathias]

Fixes: f8f80be5 ("xhci: Use soft retry to recover faster from transaction errors")
Cc: <stable@vger.kernel.org> # 4.20+
Reported-by: NBernhard <bernhard.gebetsberger@gmx.at>
Tested-by: NBernhard <bernhard.gebetsberger@gmx.at>
Signed-off-by: NStanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202541
Link: https://lore.kernel.org/r/20210311115353.2137560-2-mathias.nyman@linux.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a quirk for Samsung PM1725a drive which fixes timeouts and
I/O errors due to the fact that the controller does not properly
handle the Write Zeroes command, dmesg log:

nvme nvme0: I/O 528 QID 10 timeout, aborting
nvme nvme0: I/O 529 QID 10 timeout, aborting
nvme nvme0: I/O 530 QID 10 timeout, aborting
nvme nvme0: I/O 531 QID 10 timeout, aborting
nvme nvme0: I/O 532 QID 10 timeout, aborting
nvme nvme0: I/O 533 QID 10 timeout, aborting
nvme nvme0: I/O 534 QID 10 timeout, aborting
nvme nvme0: I/O 535 QID 10 timeout, aborting
nvme nvme0: Abort status: 0x0
nvme nvme0: Abort status: 0x0
nvme nvme0: Abort status: 0x0
nvme nvme0: Abort status: 0x0
nvme nvme0: Abort status: 0x0
nvme nvme0: Abort status: 0x0
nvme nvme0: Abort status: 0x0
nvme nvme0: Abort status: 0x0
nvme nvme0: I/O 528 QID 10 timeout, reset controller
nvme nvme0: controller is down; will reset: CSTS=0x3, PCI_STATUS=0x10
nvme nvme0: Device not ready; aborting reset, CSTS=0x3
nvme nvme0: Device not ready; aborting reset, CSTS=0x3
nvme nvme0: Removing after probe failure status: -19
nvme0n1: detected capacity change from 6251233968 to 0
blk_update_request: I/O error, dev nvme0n1, sector 32776 op 0x1:(WRITE) flags 0x3000 phys_seg 6 prio class 0
blk_update_request: I/O error, dev nvme0n1, sector 113319936 op 0x9:(WRITE_ZEROES) flags 0x800 phys_seg 0 prio class 0
Buffer I/O error on dev nvme0n1p2, logical block 1, lost async page write
blk_update_request: I/O error, dev nvme0n1, sector 113319680 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0
Buffer I/O error on dev nvme0n1p2, logical block 2, lost async page write
blk_update_request: I/O error, dev nvme0n1, sector 113319424 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0
Buffer I/O error on dev nvme0n1p2, logical block 3, lost async page write
blk_update_request: I/O error, dev nvme0n1, sector 113319168 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0
Buffer I/O error on dev nvme0n1p2, logical block 4, lost async page write
blk_update_request: I/O error, dev nvme0n1, sector 113318912 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0
Buffer I/O error on dev nvme0n1p2, logical block 5, lost async page write
blk_update_request: I/O error, dev nvme0n1, sector 113318656 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0
Buffer I/O error on dev nvme0n1p2, logical block 6, lost async page write
blk_update_request: I/O error, dev nvme0n1, sector 113318400 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0
blk_update_request: I/O error, dev nvme0n1, sector 113318144 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0
blk_update_request: I/O error, dev nvme0n1, sector 113317888 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0
Signed-off-by: NDmitry Monakhov <dmtrmonakhov@yandex-team.ru>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

In nvmet_rdma_write_data_done, rsp is recoverd by wc->wr_cqe and freed by
nvmet_rdma_release_rsp(). But after that, pr_info() used the freed
chunk's member object and could leak the freed chunk address with
wc->wr_cqe by computing the offset.
Signed-off-by: NLv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Ensure multiple Command Sets are supported before starting to setup a
ZNS namespace.
Signed-off-by: NChaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
[hch: move the check around a bit]
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Recent patch to prevent calling __nvme_fc_abort_outstanding_ios in
interrupt context results in a possible race condition. A controller
reset results in errored io completions, which schedules error
work. The change of error work to a work element allows it to fire
after the ctrl state transition to NVME_CTRL_CONNECTING, causing
any outstanding io (used to initialize the controller) to fail and
cause problems for connect_work.

Add a state check to only schedule error work if not in the RESETTING
state.

Fixes: 19fce047 ("nvme-fc: avoid calling _nvme_fc_abort_outstanding_ios from interrupt context")
Signed-off-by: NNigel Kirkland <nkirkland2304@gmail.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

When a command has been aborted we should return NVME_SC_HOST_ABORTED_CMD
to be consistent with the other transports.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Reviewed-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NDaniel Wagner <dwagner@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

nvme_fc_terminate_exchange() is being called when exchanges are
being deleted, and as such we should be setting the NVME_REQ_CANCELLED
flag to have identical behaviour on all transports.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NKeith Busch <kbusch@kernel.org>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Reviewed-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NDaniel Wagner <dwagner@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

NVME_REQ_CANCELLED is translated into -EINTR in nvme_submit_sync_cmd(),
so we should be setting this flags during nvme_cancel_request() to
ensure that the callers to nvme_submit_sync_cmd() will get the correct
error code when the controller is reset.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NKeith Busch <kbusch@kernel.org>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Reviewed-by: NChao Leng <lengchao@huawei.com>
Reviewed-by: NDaniel Wagner <dwagner@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

We only should remove namespaces when we get fatal error back from
the device or when the namespace IDs have changed.
So instead of painfully masking out error numbers which might indicate
that the error should be ignored we could use an NVME status code
to indicated when the namespace should be removed.
That simplifies the final logic and makes it less error-prone.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NKeith Busch <kbusch@kernel.org>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Reviewed-by: NDaniel Wagner <dwagner@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The chunk_sectors value affects max_zone_append_sectors.
Signed-off-by: NChaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: NKeith Busch <kbusch@kernel.org>
Tested-by: NKanchan Joshi <joshi.k@samsung.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The histogram mode is set using 'rkisp1_params_set_bits'.
Only the bits of the mode should be the value argument for
that function. Otherwise bits outside the mode mask are
turned on which is not what was intended.

Fixes: bae1155c ("media: staging: rkisp1: add output device for parameters")
Signed-off-by: NDafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+huawei@kernel.org>

RZ/G2L SoC has no UIF. This patch fixes null pointer access, when UIF
module is not used.

Fixes: 5e824f98("media: v4l: vsp1: Integrate DISCOM in display pipeline")
Signed-off-by: NBiju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+huawei@kernel.org>

RZ/G2L SoC has only BRS. This patch fixes null pointer access,when only
BRS is enabled.

Fixes: cbb7fa49("media: v4l: vsp1: Rename BRU to BRx")
Signed-off-by: NBiju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+huawei@kernel.org>

usbtv doesn't support power management, so on system suspend the
.disconnect callback of the driver is called. The teardown sequence
includes a call to snd_card_free. Its implementation waits until the
refcount of the sound card device drops to zero, however, if its file is
open, snd_card_file_add takes a reference, which can't be dropped during
the suspend, because the userspace processes are already frozen at this
point. snd_card_free waits for completion forever, leading to a hang on
suspend.

This commit fixes this deadlock condition by replacing snd_card_free
with snd_card_free_when_closed, that doesn't wait until all references
are released, allowing suspend to progress.

Fixes: 63ddf68d ("[media] usbtv: add audio support")
Signed-off-by: NMaxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+huawei@kernel.org>

The rc-cec keymap is unusual in that it can't be built as a module,
instead it is registered directly in rc-main.c if CONFIG_MEDIA_CEC_RC
is set. This is because it can be called from drm_dp_cec_set_edid() via
cec_register_adapter() in an asynchronous context, and it is not
allowed to use request_module() to load rc-cec.ko in that case. Trying to
do so results in a 'WARN_ON_ONCE(wait && current_is_async())'.

Since this keymap is only used if CONFIG_MEDIA_CEC_RC is set, we
just compile this keymap into the rc-core module and never as a
separate module.
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 2c6d1fff (drm: add support for DisplayPort CEC-Tunneling-over-AUX)
Reported-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+huawei@kernel.org>

Some of them have gaps, or fields we don't clear. Native ioctl code
does full copies plus zero-extends on size mismatch, so nothing can
leak. But compat is more hand-rolled so need to be careful.

None of these matter for performance, so just memset.

Also I didn't fix up the CONFIG_DRM_LEGACY or CONFIG_DRM_AGP ioctl, those
are security holes anyway.
Acked-by: NMaxime Ripard <mripard@kernel.org>
Reported-by: syzbot+620cf21140fc7e772a5d@syzkaller.appspotmail.com # vblank ioctl
Cc: syzbot+620cf21140fc7e772a5d@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222100643.400935-1-daniel.vetter@ffwll.ch
(cherry picked from commit e926c474)
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

dma-buf importing was reworked in commit 7d2cd72a
("drm/shmem-helpers: Simplify dma-buf importing"). Before that commit
drm_gem_shmem_prime_import_sg_table() did set ->pages_use_count=1 and
drm_gem_shmem_vunmap_locked() could call drm_gem_shmem_put_pages()
unconditionally. Now without the use count set, put pages is called also
on dma-bufs. Fix this by only putting pages if it's not imported.
Signed-off-by: NNoralf Trønnes <noralf@tronnes.org>
Fixes: 7d2cd72a ("drm/shmem-helpers: Simplify dma-buf importing")
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: NThomas Zimmermann <tzimmermann@suse.de>
Tested-by: NThomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219122203.51130-1-noralf@tronnes.org
(cherry picked from commit cdea7251)
Signed-off-by: NThomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Problem: random stucks on reboot stage about 1/20 stuck/reboots
// debug kernel log
[    4.496660] reboot: kernel restart prepare CMD:(null)
[    4.498114] meson_ee_pwrc c883c000.system-controller:power-controller: shutdown begin
[    4.503949] meson_ee_pwrc c883c000.system-controller:power-controller: shutdown domain 0:VPU...
...STUCK...

Solution: add shutdown function to meson_drm driver
// debug kernel log
[    5.231896] reboot: kernel restart prepare CMD:(null)
[    5.246135] [drm:meson_drv_shutdown]
...
[    5.259271] meson_ee_pwrc c883c000.system-controller:power-controller: shutdown begin
[    5.274688] meson_ee_pwrc c883c000.system-controller:power-controller: shutdown domain 0:VPU...
[    5.338331] reboot: Restarting system
[    5.358293] psci: PSCI_0_2_FN_SYSTEM_RESET reboot_mode:0 cmd:(null)
bl31 reboot reason: 0xd
bl31 reboot reason: 0x0
system cmd  1.
...REBOOT...

Tested: on VIM1 VIM2 VIM3 VIM3L khadas sbcs - 1000+ successful reboots
and Odroid boards, WeTek Play2 (GXBB)

Fixes: bbbe775e ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: NArtem Lapkin <art@khadas.com>
Tested-by: NChristian Hewitt <christianshewitt@gmail.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210302042202.3728113-1-art@khadas.comSigned-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>