In this case, need to add element to device private to hold
original led state.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also fix up incorrect docbook comment
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement new ethtool set_phys_id on Chelsio cxgb3 board.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement control of LED via set_phys_id.
Note: since PHY is powered off if device is down, this board
only allows blinking if device is up.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement set_phys_id led control on SysKonnect board.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use ethtool set_phys_id to control LED. Fixes issues with RTNL being
held for extended periods.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bumped up version number to 5.0.16
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o In dev->open LRO was enabled by default, enable it depending
  upon netdev->features , kernel may have disabled it.
o Configure LRO when interface is up.
Signed-off-by: NRajesh Borundia <Rajesh.Borundia@qlogic.com>
Signed-off-by: NAnirban Chakraborty <Anirban.Chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use flash layout table to get flash fw starting address and its size.
If that fails, use legacy method.
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleaned up unused codes for interrupt coalescence settings
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Made changes to VLAN code comply with new VLAN infrastructure in kernel
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Optimized code resulted in achieving lower CPU utilization on transmit path
and higher throughput for small packet sizes (64 bytes).
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

 1. Changed adapter structure to move away from embedding hardware and
    receive context structs and use pointers to those objects
 2. Packed all the structs that interface with FW
 3. Removed unused code and structs
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a memory leak in error path of pci info.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before this fix, PCI info was available only when multiple NIC functions
are present on the same port.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes spin_locks at CAN socket creation time by using RCU.

Inspired by the discussion with Kurt van Dijck and Eric Dumazet the RCU code
was partly derived from af_phonet.c
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Reviewed-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NKurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a 5717 or 5719 NVRAM part is manually strapped and is 2mb in size,
the driver needs to look at the NVRAM size field rather than infer it
from the strapping itself.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the 5720 device ID to the PCI table, thus enabling 5720
support.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the 5720 PHY ID.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the new Host to BMC feature.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5720 implements its own NVRAM pin strapping scheme.  This patch adds
the required support.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the 5720 ASIC rev.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reintroduces the TG3_FLG3_5717_PLUS to identify 5717 and
later devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 57765 arrived before the 5717 and has a subset of the features
supported by the 5717.  This patch renames the 5717_PLUS flag so that it
can be reintroduced to designate only 5717 and later devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardcoded values are used in multiple places to describe the maximum rx
ring sizes.  This patch replaces those values with preprocessor
constants.  This patch also introduces a new TG3_FLG3_LRG_PROD_RING_CAP
to determine if the device is capable of supporting larger ring sizes.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The ethtool ETHTOOL_PHYS_ID command runs for an arbitrarily long
period of time, holding the RTNL lock.  This blocks routing updates,
device enumeration, and various important operations that one might
want to keep running while hunting for the flashing LED.

We need to drop the RTNL lock during this operation, but currently the
core implementation is a thin wrapper around a driver operation and
drivers may well depend upon holding the lock.

Define a new driver operation 'set_phys_id' with an argument that sets
the ID indicator on/off/inactive/active (the last optional, for any
driver or firmware that prefers to handle blinking asynchronously).
When this is defined, the ethtool core drops the lock while waiting
and only acquires it around calls to this operation.

Deprecate the 'phys_id' operation in favour of this.  It can be
removed once all in-tree drivers are converted.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Briefly document all operations (except get_rx_ntuple), including
whether they may return an error code and whether they are deprecated.
Also mention some things that should be handled by the ethtool core
rather than by drivers.

Briefly document general requirements for callers.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The TSO code already supports IPv6 on VLAN, so enable it.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

This patch uses __copy_from_user_nocache on transmit to bypass data
cache for a performance improvement.  skb_add_data_nocache and
skb_copy_to_page_nocache can be called by sendmsg functions to use
this feature, initial support is in tcp_sendmsg.  This functionality is
configurable per device using ethtool.

Presumably, this feature would only be useful when the driver does
not touch the data.  The feature is turned on by default if a device
indicates that it does some form of checksum offload; it is off by
default for devices that do no checksum offload or indicate no checksum
is necessary.  For the former case copy-checksum is probably done
anyway, in the latter case the device is likely loopback in which case
the no cache copy is probably not beneficial.

This patch was tested using 200 instances of netperf TCP_RR with
1400 byte request and one byte reply.  Platform is 16 core AMD x86.

No-cache copy disabled:
   672703 tps, 97.13% utilization
   50/90/99% latency:244.31 484.205 1028.41

No-cache copy enabled:
   702113 tps, 96.16% utilization,
   50/90/99% latency 238.56 467.56 956.955

Using 14000 byte request and response sizes demonstrate the
effects more dramatically:

No-cache copy disabled:
   79571 tps, 34.34 %utlization
   50/90/95% latency 1584.46 2319.59 5001.76

No-cache copy enabled:
   83856 tps, 34.81% utilization
   50/90/95% latency 2508.42 2622.62 2735.88

Note especially the effect on latency tail (95th percentile).

This seems to provide a nice performance improvement and is
consistent in the tests I ran.  Presumably, this would provide
the greatest benfits in the presence of an application workload
stressing the cache and a lot of transmit data happening.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Apply restrictions on STP parameters based 802.1D 1998 standard.
   * Fixes missing locking in set path cost ioctl
   * Uses common code for both ioctl and sysfs

This is based on an earlier patch Sasikanth V but with overhaul.

Note:
1. It does NOT enforce the restriction on the relationship max_age and
   forward delay or hello time because in existing implementation these are
   set as independant operations.

2. If STP is disabled, there is no restriction on forward delay

3. No restriction on holding time because users use Linux code to act
   as hub or be sticky.

4. Although standard allow 0-255, Linux only allows 0-63 for port priority
   because more bits are reserved for port number.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add netlink device ops to allow creating bridge device via netlink.
This works in a manner similar to vlan, macvlan and bonding.

Example:
  # ip link add link dev br0 type bridge
  # ip link del dev br0

The change required rearranging initializtion code to deal with
being called by create link. Most of the initialization happens
in br_dev_setup, but allocation of stats is done in ndo_init callback
to deal with allocation failure. Sysfs setup has to wait until
after the network device kobject is registered.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use RTM_NEWNEIGH and RTM_DELNEIGH to allow updating of entries
in bridge forwarding table. This allows manipulating static entries
which is not possible with existing tools.

Example (using bridge extensions to iproute2)
   # br fdb add 00:02:03:04:05:06 dev eth0
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows applications to query and monitor bridge forwarding
table in the same method used for neighbor table. The forward table
entries are returned in same structure format as used by the ioctl.
If more information is desired in future, the netlink method is
extensible.

Example (using bridge extensions to iproute2)
  # br monitor
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some cases, look up of forward database entry is done with RCU;
and for others no RCU is needed because of locking. Split the two
cases into two differnt loops (and take off inline).
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds tracking the last used time in forwarding table.
Rename ageing_timer to updated to better describe it.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Later patch provides ability to create non-local static entry.
To make this easier move the updating of the flag values to
after the code that creates entry.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>