At the moment we initialise the target *mask* of a virtual IRQ to the
VCPU it belongs to, even though this mask is only defined for GICv2 and
quickly runs out of bits for many GICv3 guests.
This behaviour triggers an UBSAN complaint for more than 32 VCPUs:
------
[ 5659.462377] UBSAN: Undefined behaviour in virt/kvm/arm/vgic/vgic-init.c:223:21
[ 5659.471689] shift exponent 32 is too large for 32-bit type 'unsigned int'
------
Also for GICv3 guests the reporting of TARGET in the "vgic-state" debugfs
dump is wrong, due to this very same problem.

Because there is no requirement to create the VGIC device before the
VCPUs (and QEMU actually does it the other way round), we can't safely
initialise mpidr or targets in kvm_vgic_vcpu_init(). But since we touch
every private IRQ for each VCPU anyway later (in vgic_init()), we can
just move the initialisation of those fields into there, where we
definitely know the VGIC type.

On the way make sure we really have either a VGICv2 or a VGICv3 device,
since the existing code is just checking for "VGICv3 or not", silently
ignoring the uninitialised case.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reported-by: NDave Martin <dave.martin@arm.com>
Tested-by: NJulien Grall <julien.grall@arm.com>
Signed-off-by: NMarc Zyngier <maz@kernel.org>

If after an MMIO exit to userspace a VCPU is immediately run with an
immediate_exit request, such as when a signal is delivered or an MMIO
emulation completion is needed, then the VCPU completes the MMIO
emulation and immediately returns to userspace. As the exit_reason
does not get changed from KVM_EXIT_MMIO in these cases we have to
be careful not to complete the MMIO emulation again, when the VCPU is
eventually run again, because the emulation does an instruction skip
(and doing too many skips would be a waste of guest code :-) We need
to use additional VCPU state to track if the emulation is complete.
As luck would have it, we already have 'mmio_needed', which even
appears to be used in this way by other architectures already.

Fixes: 0d640732 ("arm64: KVM: Skip MMIO insn after emulation")
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <maz@kernel.org>

A HW mapped level sensitive interrupt asserted by a device will not be put
into the ap_list if it is disabled at the VGIC level. When it is enabled
again, it will be inserted into the ap_list and written to a list register
on guest entry regardless of the state of the device.

We could argue that this can also happen on real hardware, when the command
to enable the interrupt reached the GIC before the device had the chance to
de-assert the interrupt signal; however, we emulate the distributor and
redistributors in software and we can do better than that.
Signed-off-by: NAlexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: NMarc Zyngier <maz@kernel.org>

At the moment, the way we reset CP15 registers is mildly insane:
We write junk to them, call the reset functions, and then check that
we have something else in them.

The "fun" thing is that this can happen while the guest is running
(PSCI, for example). If anything in KVM has to evaluate the state
of a CP15 register while junk is in there, bad thing may happen.

Let's stop doing that. Instead, we track that we have called a
reset function for that register, and assume that the reset
function has done something.

In the end, the very need of this reset check is pretty dubious,
as it doesn't check everything (a lot of the CP15 reg leave outside
of the cp15_regs[] array). It may well be axed in the near future.
Signed-off-by: NMarc Zyngier <maz@kernel.org>

At the moment, the way we reset system registers is mildly insane:
We write junk to them, call the reset functions, and then check that
we have something else in them.

The "fun" thing is that this can happen while the guest is running
(PSCI, for example). If anything in KVM has to evaluate the state
of a system register while junk is in there, bad thing may happen.

Let's stop doing that. Instead, we track that we have called a
reset function for that register, and assume that the reset
function has done something. This requires fixing a couple of
sysreg refinition in the trap table.

In the end, the very need of this reset check is pretty dubious,
as it doesn't check everything (a lot of the sysregs leave outside of
the sys_regs[] array). It may well be axed in the near future.
Tested-by: NZenghui Yu <yuzenghui@huawei.com>
Signed-off-by: NMarc Zyngier <maz@kernel.org>

Since commit commit 328e5664 ("KVM: arm/arm64: vgic: Defer
touching GICH_VMCR to vcpu_load/put"), we leave ICH_VMCR_EL2 (or
its GICv2 equivalent) loaded as long as we can, only syncing it
back when we're scheduled out.

There is a small snag with that though: kvm_vgic_vcpu_pending_irq(),
which is indirectly called from kvm_vcpu_check_block(), needs to
evaluate the guest's view of ICC_PMR_EL1. At the point were we
call kvm_vcpu_check_block(), the vcpu is still loaded, and whatever
changes to PMR is not visible in memory until we do a vcpu_put().

Things go really south if the guest does the following:

	mov x0, #0	// or any small value masking interrupts
	msr ICC_PMR_EL1, x0

	[vcpu preempted, then rescheduled, VMCR sampled]

	mov x0, #ff	// allow all interrupts
	msr ICC_PMR_EL1, x0
	wfi		// traps to EL2, so samping of VMCR

	[interrupt arrives just after WFI]

Here, the hypervisor's view of PMR is zero, while the guest has enabled
its interrupts. kvm_vgic_vcpu_pending_irq() will then say that no
interrupts are pending (despite an interrupt being received) and we'll
block for no reason. If the guest doesn't have a periodic interrupt
firing once it has blocked, it will stay there forever.

To avoid this unfortuante situation, let's resync VMCR from
kvm_arch_vcpu_blocking(), ensuring that a following kvm_vcpu_check_block()
will observe the latest value of PMR.

This has been found by booting an arm64 Linux guest with the pseudo NMI
feature, and thus using interrupt priorities to mask interrupts instead
of the usual PSTATE masking.

Cc: stable@vger.kernel.org # 4.12
Fixes: 328e5664 ("KVM: arm/arm64: vgic: Defer touching GICH_VMCR to vcpu_load/put")
Signed-off-by: NMarc Zyngier <maz@kernel.org>

When fall-through warnings was enabled by default the following warnings
was starting to show up:

../arch/arm64/kvm/hyp/debug-sr.c: In function ‘__debug_save_state’:
../arch/arm64/kvm/hyp/debug-sr.c:20:19: warning: this statement may fall
 through [-Wimplicit-fallthrough=]
  case 15: ptr[15] = read_debug(reg, 15);   \
../arch/arm64/kvm/hyp/debug-sr.c:113:2: note: in expansion of macro ‘save_debug’
  save_debug(dbg->dbg_bcr, dbgbcr, brps);
  ^~~~~~~~~~
../arch/arm64/kvm/hyp/debug-sr.c:21:2: note: here
  case 14: ptr[14] = read_debug(reg, 14);   \
  ^~~~
../arch/arm64/kvm/hyp/debug-sr.c:113:2: note: in expansion of macro ‘save_debug’
  save_debug(dbg->dbg_bcr, dbgbcr, brps);
  ^~~~~~~~~~
../arch/arm64/kvm/hyp/debug-sr.c:21:19: warning: this statement may fall
 through [-Wimplicit-fallthrough=]
  case 14: ptr[14] = read_debug(reg, 14);   \
../arch/arm64/kvm/hyp/debug-sr.c:113:2: note: in expansion of macro ‘save_debug’
  save_debug(dbg->dbg_bcr, dbgbcr, brps);
  ^~~~~~~~~~
../arch/arm64/kvm/hyp/debug-sr.c:22:2: note: here
  case 13: ptr[13] = read_debug(reg, 13);   \
  ^~~~
../arch/arm64/kvm/hyp/debug-sr.c:113:2: note: in expansion of macro ‘save_debug’
  save_debug(dbg->dbg_bcr, dbgbcr, brps);
  ^~~~~~~~~~

Rework to add a 'Fall through' comment where the compiler warned
about fall-through, hence silencing the warning.

Fixes: d93512ef0f0e ("Makefile: Globally enable fall-through warning")
Signed-off-by: NAnders Roxell <anders.roxell@linaro.org>
[maz: fixed commit message]
Signed-off-by: NMarc Zyngier <maz@kernel.org>

We've added two ESR exception classes for new ARM hardware extensions:
ESR_ELx_EC_PAC and ESR_ELx_EC_SVE, but failed to update the strings
used in tracing and other debug.

Let's update "kvm_arm_exception_class" for these two EC, which the
new EC will be visible to user-space via kvm_exit trace events
Also update to "esr_class_str" for ESR_ELx_EC_PAC, by which we can
get more readable debug info.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NZenghui Yu <yuzenghui@huawei.com>
Signed-off-by: NMarc Zyngier <maz@kernel.org>

When fall-through warnings was enabled by default the following warnings
was starting to show up:

../virt/kvm/arm/hyp/vgic-v3-sr.c: In function ‘__vgic_v3_save_aprs’:
../virt/kvm/arm/hyp/vgic-v3-sr.c:351:24: warning: this statement may fall
 through [-Wimplicit-fallthrough=]
   cpu_if->vgic_ap0r[2] = __vgic_v3_read_ap0rn(2);
   ~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~
../virt/kvm/arm/hyp/vgic-v3-sr.c:352:2: note: here
  case 6:
  ^~~~
../virt/kvm/arm/hyp/vgic-v3-sr.c:353:24: warning: this statement may fall
 through [-Wimplicit-fallthrough=]
   cpu_if->vgic_ap0r[1] = __vgic_v3_read_ap0rn(1);
   ~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~
../virt/kvm/arm/hyp/vgic-v3-sr.c:354:2: note: here
  default:
  ^~~~~~~

Rework so that the compiler doesn't warn about fall-through.

Fixes: d93512ef0f0e ("Makefile: Globally enable fall-through warning")
Signed-off-by: NAnders Roxell <anders.roxell@linaro.org>
Signed-off-by: NMarc Zyngier <maz@kernel.org>

When fall-through warnings was enabled by default, commit d93512ef0f0e
("Makefile: Globally enable fall-through warning"), the following
warnings was starting to show up:

In file included from ../arch/arm64/include/asm/kvm_emulate.h:19,
                 from ../arch/arm64/kvm/regmap.c:13:
../arch/arm64/kvm/regmap.c: In function ‘vcpu_write_spsr32’:
../arch/arm64/include/asm/kvm_hyp.h:31:3: warning: this statement may fall
 through [-Wimplicit-fallthrough=]
   asm volatile(ALTERNATIVE(__msr_s(r##nvh, "%x0"), \
   ^~~
../arch/arm64/include/asm/kvm_hyp.h:46:31: note: in expansion of macro ‘write_sysreg_elx’
 #define write_sysreg_el1(v,r) write_sysreg_elx(v, r, _EL1, _EL12)
                               ^~~~~~~~~~~~~~~~
../arch/arm64/kvm/regmap.c:180:3: note: in expansion of macro ‘write_sysreg_el1’
   write_sysreg_el1(v, SYS_SPSR);
   ^~~~~~~~~~~~~~~~
../arch/arm64/kvm/regmap.c:181:2: note: here
  case KVM_SPSR_ABT:
  ^~~~
In file included from ../arch/arm64/include/asm/cputype.h:132,
                 from ../arch/arm64/include/asm/cache.h:8,
                 from ../include/linux/cache.h:6,
                 from ../include/linux/printk.h:9,
                 from ../include/linux/kernel.h:15,
                 from ../include/asm-generic/bug.h:18,
                 from ../arch/arm64/include/asm/bug.h:26,
                 from ../include/linux/bug.h:5,
                 from ../include/linux/mmdebug.h:5,
                 from ../include/linux/mm.h:9,
                 from ../arch/arm64/kvm/regmap.c:11:
../arch/arm64/include/asm/sysreg.h:837:2: warning: this statement may fall
 through [-Wimplicit-fallthrough=]
  asm volatile("msr " __stringify(r) ", %x0"  \
  ^~~
../arch/arm64/kvm/regmap.c:182:3: note: in expansion of macro ‘write_sysreg’
   write_sysreg(v, spsr_abt);
   ^~~~~~~~~~~~
../arch/arm64/kvm/regmap.c:183:2: note: here
  case KVM_SPSR_UND:
  ^~~~

Rework to add a 'break;' in the swich-case since it didn't have that,
leading to an interresting set of bugs.

Cc: stable@vger.kernel.org # v4.17+
Fixes: a8928195 ("KVM: arm64: Prepare to handle deferred save/restore of 32-bit registers")
Signed-off-by: NAnders Roxell <anders.roxell@linaro.org>
[maz: reworked commit message, fixed stable range]
Signed-off-by: NMarc Zyngier <maz@kernel.org>

We use "pmc->idx" and the "chained" bitmap to determine if the pmc is
chained, in kvm_pmu_pmc_is_chained().  But idx might be uninitialized
(and random) when we doing this decision, through a KVM_ARM_VCPU_INIT
ioctl -> kvm_pmu_vcpu_reset(). And the test_bit() against this random
idx will potentially hit a KASAN BUG [1].

In general, idx is the static property of a PMU counter that is not
expected to be modified across resets, as suggested by Julien.  It
looks more reasonable if we can setup the PMU counter idx for a vcpu
in its creation time. Introduce a new function - kvm_pmu_vcpu_init()
for this basic setup. Oh, and the KASAN BUG will get fixed this way.

[1] https://www.spinics.net/lists/kvm-arm/msg36700.html

Fixes: 80f393a2 ("KVM: arm/arm64: Support chained PMU counters")
Suggested-by: NAndrew Murray <andrew.murray@arm.com>
Suggested-by: NJulien Thierry <julien.thierry@arm.com>
Acked-by: NJulien Thierry <julien.thierry@arm.com>
Signed-off-by: NZenghui Yu <yuzenghui@huawei.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Pull Devicetree fixes from Rob Herring:
 "Fix several warnings/errors in validation of binding schemas"

* tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
  dt-bindings: iio: ad7124: Fix dtc warnings in example
  dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
  dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
  dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
  dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
  dt-bindings: Ensure child nodes are of type 'object'

Pull vfs documentation typo fix from Al Viro.

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  typo fix: it's d_make_root, not d_make_inode...

Pull cifs fixes from Steve French:
 "Two fixes for stable, one that had dependency on earlier patch in this
  merge window and can now go in, and a perf improvement in SMB3 open"

* tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module number
  cifs: flush before set-info if we have writeable handles
  smb3: optimize open to not send query file internal info
  cifs: copy_file_range needs to strip setuid bits and update timestamps
  CIFS: fix deadlock in cached root handling

The commit b3aa14f0 ("iommu: remove the mapping_error dma_map_ops
method") incorrectly changed the checking from dma_ops_alloc_iova() in
map_sg() causes a crash under memory pressure as dma_ops_alloc_iova()
never return DMA_MAPPING_ERROR on failure but 0, so the error handling
is all wrong.

   kernel BUG at drivers/iommu/iova.c:801!
    Workqueue: kblockd blk_mq_run_work_fn
    RIP: 0010:iova_magazine_free_pfns+0x7d/0xc0
    Call Trace:
     free_cpu_cached_iovas+0xbd/0x150
     alloc_iova_fast+0x8c/0xba
     dma_ops_alloc_iova.isra.6+0x65/0xa0
     map_sg+0x8c/0x2a0
     scsi_dma_map+0xc6/0x160
     pqi_aio_submit_io+0x1f6/0x440 [smartpqi]
     pqi_scsi_queue_command+0x90c/0xdd0 [smartpqi]
     scsi_queue_rq+0x79c/0x1200
     blk_mq_dispatch_rq_list+0x4dc/0xb70
     blk_mq_sched_dispatch_requests+0x249/0x310
     __blk_mq_run_hw_queue+0x128/0x200
     blk_mq_run_work_fn+0x27/0x30
     process_one_work+0x522/0xa10
     worker_thread+0x63/0x5b0
     kthread+0x1d2/0x1f0
     ret_from_fork+0x22/0x40

Fixes: b3aa14f0 ("iommu: remove the mapping_error dma_map_ops method")
Signed-off-by: NQian Cai <cai@lca.pw>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The hexagon implementation pte_alloc_one(), pte_alloc_one_kernel(),
pte_free_kernel() and pte_free() is identical to the generic except of
lack of __GFP_ACCOUNT for the user PTEs allocation.

Switch hexagon to use generic version of these functions.
Signed-off-by: NMike Rapoport <rppt@linux.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull NTB updates from Jon Mason:
 "New feature to add support for NTB virtual MSI interrupts, the ability
  to test and use this feature in the NTB transport layer.

  Also, bug fixes for the AMD and Switchtec drivers, as well as some
  general patches"

* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
  NTB: Describe the ntb_msi_test client in the documentation.
  NTB: Add MSI interrupt support to ntb_transport
  NTB: Add ntb_msi_test support to ntb_test
  NTB: Introduce NTB MSI Test Client
  NTB: Introduce MSI library
  NTB: Rename ntb.c to support multiple source files in the module
  NTB: Introduce functions to calculate multi-port resource index
  NTB: Introduce helper functions to calculate logical port number
  PCI/switchtec: Add module parameter to request more interrupts
  PCI/MSI: Support allocating virtual MSI interrupts
  ntb_hw_switchtec: Fix setup MW with failure bug
  ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
  ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
  NTB: correct ntb_dev_ops and ntb_dev comment typos
  NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
  ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
  NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
  NTB: ntb_hw_amd: set peer limit register
  NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
  NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
  ...

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Now that examples are validated against the DT schema, an error with
required 'clocks' property missing is exposed:

Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@40020000: gpio@0: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@1000: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@2000: 'clocks' is a required property

Add the missing 'clocks' properties to the examples to fix the errors.

Fixes: 2c9239c1 ("dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Acked-by: NAlexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: NRob Herring <robh@kernel.org>

With the conversion to DT schema, the examples are now compiled with
dtc. The ad7124 binding example has the following warning:

Documentation/devicetree/bindings/iio/adc/adi,ad7124.example.dts:19.11-21: \
Warning (reg_format): /example-0/adc@0:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)

There's a default #size-cells and #address-cells values of 1 for
examples. For examples needing different values such as this one on a
SPI bus, they need to provide a SPI bus parent node.

Fixes: 26ae15e6 ("Convert AD7124 bindings documentation to YAML format.")

Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: NRob Herring <robh@kernel.org>

Now that examples are validated against the DT schema, a typo in
avia-hx711 example generates a warning:

Documentation/devicetree/bindings/iio/adc/avia-hx711.example.dt.yaml: weight: 'avdd-supply' is a required property

Fix the typo.

Fixes: 5150ec3f ("avia-hx711.yaml: transform DT binding to YAML")
Cc: Andreas Klinger <ak@it-klinger.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: NRob Herring <robh@kernel.org>

The schema examples are now validated against the schema itself. The
AST2500 pinctrl schema has a couple of errors:

Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
example-0: $nodename:0: 'example-0' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
pinctrl: aspeed,external-nodes: [[1, 2]] is too short

Fixes: 0a617de1 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema")
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: NAndrew Jeffery <andrew@aj.id.au>
Signed-off-by: NRob Herring <robh@kernel.org>

The Aspeed pinctl schema have errors in the 'compatible' schema:

Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2400-pinctrl', 'aspeed', 'g4-pinctrl'] has non-unique elements
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2500-pinctrl', 'aspeed', 'g5-pinctrl'] has non-unique elements

Flow style sequences have to be quoted if the vales contain ','. Fix
this by using the more common one line per entry formatting.

Fixes: 0a617de1 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema")
Fixes: 07457937 ("dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema")
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: NAndrew Jeffery <andrew@aj.id.au>
Signed-off-by: NRob Herring <robh@kernel.org>

Matching on the 'cpus' node was a bad choice because the schema is
incorrectly applied to non-RiscV cpus nodes. As we now have a common cpus
schema which checks the general structure, it is also redundant to do so
in the Risc-V CPU schema.

The downside is one could conceivably mix different architecture's cpu
nodes or have typos in the compatible string. The latter problem pretty
much exists for every schema.
Acked-by: NPaul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: NRob Herring <robh@kernel.org>

Properties which are child node definitions need to have an explict
type. Otherwise, a matching (DT) property can silently match when an
error is desired. Fix this up tree-wide. Once this is fixed, the
meta-schema will enforce this on any child node definitions.

Cc: Chen-Yu Tsai <wens@csie.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-spi@vger.kernel.org
Acked-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Acked-by: NMark Brown <broonie@kernel.org>
Acked-by: NAlexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: NRob Herring <robh@kernel.org>

Pull more input updates from Dmitry Torokhov:

 - Apple SPI keyboard and trackpad driver for newer Macs

 - ALPS driver will ignore trackpoint-only devices to give the
   trackpoint driver a chance to handle them properly

 - another Lenovo is switched over to SMbus from PS/2

 - assorted driver fixups.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: alps - fix a mismatch between a condition check and its comment
  Input: psmouse - fix build error of multiple definition
  Input: applespi - remove set but not used variables 'sts'
  Input: add Apple SPI keyboard and trackpad driver
  Input: alps - don't handle ALPS cs19 trackpoint-only device
  Input: hyperv-keyboard - remove dependencies on PAGE_SIZE for ring buffer
  Input: adp5589 - initialize GPIO controller parent device
  Input: iforce - remove empty multiline comments
  Input: synaptics - fix misuse of strlcpy
  Input: auo-pixcir-ts - switch to using  devm_add_action_or_reset()
  Input: gtco - bounds check collection indent level
  Input: mtk-pmic-keys - add of_node_put() before return
  Input: sun4i-lradc-keys - add of_node_put() before return
  Input: synaptics - whitelist Lenovo T580 SMBus intertouch

Pull dma-mapping fixes from Christoph Hellwig:
 "Fix various regressions:

   - force unencrypted dma-coherent buffers if encryption bit can't fit
     into the dma coherent mask (Tom Lendacky)

   - avoid limiting request size if swiotlb is not used (me)

   - fix swiotlb handling in dma_direct_sync_sg_for_cpu/device (Fugang
     Duan)"

* tag 'dma-mapping-5.3-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-direct: correct the physical addr in dma_direct_sync_sg_for_cpu/device
  dma-direct: only limit the mapping size if swiotlb could be used
  dma-mapping: add a dma_addressing_limited helper
  dma-direct: Force unencrypted DMA under SME for certain DMA masks

Pull x86 fixes from Thomas Gleixner:
 "A set of x86 specific fixes and updates:

   - The CR2 corruption fixes which store CR2 early in the entry code
     and hand the stored address to the fault handlers.

   - Revert a forgotten leftover of the dropped FSGSBASE series.

   - Plug a memory leak in the boot code.

   - Make the Hyper-V assist functionality robust by zeroing the shadow
     page.

   - Remove a useless check for dead processes with LDT

   - Update paravirt and VMware maintainers entries.

   - A few cleanup patches addressing various compiler warnings"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/entry/64: Prevent clobbering of saved CR2 value
  x86/hyper-v: Zero out the VP ASSIST PAGE on allocation
  x86, boot: Remove multiple copy of static function sanitize_boot_params()
  x86/boot/compressed/64: Remove unused variable
  x86/boot/efi: Remove unused variables
  x86/mm, tracing: Fix CR2 corruption
  x86/entry/64: Update comments and sanity tests for create_gap
  x86/entry/64: Simplify idtentry a little
  x86/entry/32: Simplify common_exception
  x86/paravirt: Make read_cr2() CALLEE_SAVE
  MAINTAINERS: Update PARAVIRT_OPS_INTERFACE and VMWARE_HYPERVISOR_INTERFACE
  x86/process: Delete useless check for dead process with LDT
  x86: math-emu: Hide clang warnings for 16-bit overflow
  x86/e820: Use proper booleans instead of 0/1
  x86/apic: Silence -Wtype-limits compiler warnings
  x86/mm: Free sme_early_buffer after init
  x86/boot: Fix memory leak in default_get_smp_config()
  Revert "x86/ptrace: Prevent ptrace from clearing the FS/GS selector" and fix the test

Pull perf tooling updates from Thomas Gleixner:
 "A set of perf improvements and fixes:

  perf db-export:
   - Improvements in how COMM details are exported to databases for post
     processing and use in the sql-viewer.py UI.

   - Export switch events to the database.

  BPF:
   - Bump rlimit(MEMLOCK) for 'perf test bpf' and 'perf trace', just
     like selftests/bpf/bpf_rlimit.h do, which makes errors due to
     exhaustion of this limit, which are kinda cryptic (EPERM sometimes)
     less frequent.

  perf version:
   - Fix segfault due to missing OPT_END(), noticed on PowerPC.

  perf vendor events:
   - Add JSON files for IBM s/390 machine type 8561.

  perf cs-etm (ARM):
   - Fix two cases of error returns not bing done properly: Invalid
     ERR_PTR() use and loss of propagation error codes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
  perf version: Fix segfault due to missing OPT_END()
  perf vendor events s390: Add JSON files for machine type 8561
  perf cs-etm: Return errcode in cs_etm__process_auxtrace_info()
  perf cs-etm: Remove errnoeous ERR_PTR() usage in cs_etm__process_auxtrace_info
  perf scripts python: export-to-postgresql.py: Export switch events
  perf scripts python: export-to-sqlite.py: Export switch events
  perf db-export: Export switch events
  perf db-export: Factor out db_export__threads()
  perf script: Add scripting operation process_switch()
  perf scripts python: exported-sql-viewer.py: Use new 'has_calls' column
  perf scripts python: exported-sql-viewer.py: Remove redundant semi-colons
  perf scripts python: export-to-postgresql.py: Add has_calls column to comms table
  perf scripts python: export-to-sqlite.py: Add has_calls column to comms table
  perf db-export: Also export thread's current comm
  perf db-export: Factor out db_export__comm()
  perf scripts python: export-to-postgresql.py: Export comm details
  perf scripts python: export-to-sqlite.py: Export comm details
  perf db-export: Export comm details
  perf db-export: Fix a white space issue in db_export__sample()
  perf db-export: Move export__comm_thread into db_export__sample()
  ...

Pull core fixes from Thomas Gleixner:

 - A collection of objtool fixes which address recent fallout partially
   exposed by newer toolchains, clang, BPF and general code changes.

 - Force USER_DS for user stack traces

[ Note: the "objtool fixes" are not all to objtool itself, but for
  kernel code that triggers objtool warnings.

  Things like missing function size annotations, or code that confuses
  the unwinder etc.   - Linus]

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
  objtool: Support conditional retpolines
  objtool: Convert insn type to enum
  objtool: Fix seg fault on bad switch table entry
  objtool: Support repeated uses of the same C jump table
  objtool: Refactor jump table code
  objtool: Refactor sibling call detection logic
  objtool: Do frame pointer check before dead end check
  objtool: Change dead_end_function() to return boolean
  objtool: Warn on zero-length functions
  objtool: Refactor function alias logic
  objtool: Track original function across branches
  objtool: Add mcsafe_handle_tail() to the uaccess safe list
  bpf: Disable GCC -fgcse optimization for ___bpf_prog_run()
  x86/uaccess: Remove redundant CLACs in getuser/putuser error paths
  x86/uaccess: Don't leak AC flag into fentry from mcsafe_handle_tail()
  x86/uaccess: Remove ELF function annotation from copy_user_handle_tail()
  x86/head/64: Annotate start_cpu0() as non-callable
  x86/entry: Fix thunk function ELF sizes
  x86/kvm: Don't call kvm_spurious_fault() from .fixup
  x86/kvm: Replace vmx_vmenter()'s call to kvm_spurious_fault() with UD2
  ...

Pull smp fix from Thomas Gleixner:
 "Add warnings to the smp function calls so callers from wrong contexts
  get detected"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  smp: Warn on function calls from softirq context

Pull CONFIG_PREEMPT_RT stub config from Thomas Gleixner:
 "The real-time preemption patch set exists for almost 15 years now and
  while the vast majority of infrastructure and enhancements have found
  their way into the mainline kernel, the final integration of RT is
  still missing.

  Over the course of the last few years, we have worked on reducing the
  intrusivenness of the RT patches by refactoring kernel infrastructure
  to be more real-time friendly. Almost all of these changes were
  benefitial to the mainline kernel on their own, so there was no
  objection to integrate them.

  Though except for the still ongoing printk refactoring, the remaining
  changes which are required to make RT a first class mainline citizen
  are not longer arguable as immediately beneficial for the mainline
  kernel. Most of them are either reordering code flows or adding RT
  specific functionality.

  But this now has hit a wall and turned into a classic hen and egg
  problem:

     Maintainers are rightfully wary vs. these changes as they make only
     sense if the final integration of RT into the mainline kernel takes
     place.

  Adding CONFIG_PREEMPT_RT aims to solve this as a clear sign that RT
  will be fully integrated into the mainline kernel. The final
  integration of the missing bits and pieces will be of course done with
  the same careful approach as we have used in the past.

  While I'm aware that you are not entirely enthusiastic about that, I
  think that RT should receive the same treatment as any other widely
  used out of tree functionality, which we have accepted into mainline
  over the years.

  RT has become the de-facto standard real-time enhancement and is
  shipped by enterprise, embedded and community distros. It's in use
  throughout a wide range of industries: telecommunications, industrial
  automation, professional audio, medical devices, data acquisition,
  automotive - just to name a few major use cases.

  RT development is backed by a Linuxfoundation project which is
  supported by major stakeholders of this technology. The funding will
  continue over the actual inclusion into mainline to make sure that the
  functionality is neither introducing regressions, regressing itself,
  nor becomes subject to bitrot. There is also a lifely user community
  around RT as well, so contrary to the grim situation 5 years ago, it's
  a healthy project.

  As RT is still a good vehicle to exercise rarely used code paths and
  to detect hard to trigger issues, you could at least view it as a QA
  tool if nothing else"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/rt, Kconfig: Introduce CONFIG_PREEMPT_RT

Pull more KVM updates from Paolo Bonzini:
 "Mostly bugfixes, but also:

   - s390 support for KVM selftests

   - LAPIC timer offloading to housekeeping CPUs

   - Extend an s390 optimization for overcommitted hosts to all
     architectures

   - Debugging cleanups and improvements"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (25 commits)
  KVM: x86: Add fixed counters to PMU filter
  KVM: nVMX: do not use dangling shadow VMCS after guest reset
  KVM: VMX: dump VMCS on failed entry
  KVM: x86/vPMU: refine kvm_pmu err msg when event creation failed
  KVM: s390: Use kvm_vcpu_wake_up in kvm_s390_vcpu_wakeup
  KVM: Boost vCPUs that are delivering interrupts
  KVM: selftests: Remove superfluous define from vmx.c
  KVM: SVM: Fix detection of AMD Errata 1096
  KVM: LAPIC: Inject timer interrupt via posted interrupt
  KVM: LAPIC: Make lapic timer unpinned
  KVM: x86/vPMU: reset pmc->counter to 0 for pmu fixed_counters
  KVM: nVMX: Ignore segment base for VMX memory operand when segment not FS or GS
  kvm: x86: ioapic and apic debug macros cleanup
  kvm: x86: some tsc debug cleanup
  kvm: vmx: fix coccinelle warnings
  x86: kvm: avoid constant-conversion warning
  x86: kvm: avoid -Wsometimes-uninitized warning
  KVM: x86: expose AVX512_BF16 feature to guest
  KVM: selftests: enable pgste option for the linker on s390
  KVM: selftests: Move kvm_create_max_vcpus test to generic code
  ...

Pull SCSI fixes from James Bottomley:
 "This is the final round of mostly small fixes in our initial submit.

  It's mostly minor fixes and driver updates. The only change of note is
  adding a virt_boundary_mask to the SCSI host and host template to
  parametrise this for NVMe devices instead of having them do a call in
  slave_alloc. It's a fairly straightforward conversion except in the
  two NVMe handling drivers that didn't set it who now have a virtual
  infinity parameter added"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
  scsi: megaraid_sas: set an unlimited max_segment_size
  scsi: mpt3sas: set an unlimited max_segment_size for SAS 3.0 HBAs
  scsi: IB/srp: set virt_boundary_mask in the scsi host
  scsi: IB/iser: set virt_boundary_mask in the scsi host
  scsi: storvsc: set virt_boundary_mask in the scsi host template
  scsi: ufshcd: set max_segment_size in the scsi host template
  scsi: core: take the DMA max mapping size into account
  scsi: core: add a host / host template field for the virt boundary
  scsi: core: Fix race on creating sense cache
  scsi: sd_zbc: Fix compilation warning
  scsi: libfc: fix null pointer dereference on a null lport
  scsi: zfcp: fix GCC compiler warning emitted with -Wmaybe-uninitialized
  scsi: zfcp: fix request object use-after-free in send path causing wrong traces
  scsi: zfcp: fix request object use-after-free in send path causing seqno errors
  scsi: megaraid_sas: Update driver version to 07.710.50.00
  scsi: megaraid_sas: Add module parameter for FW Async event logging
  scsi: megaraid_sas: Enable msix_load_balance for Invader and later controllers
  scsi: megaraid_sas: Fix calculation of target ID
  scsi: lpfc: reduce stack size with CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE
  scsi: devinfo: BLIST_TRY_VPD_PAGES for SanDisk Cruzer Blade
  ...

Pull more Kbuild updates from Masahiro Yamada:

 - match the directory structure of the linux-libc-dev package to that
   of Debian-based distributions

 - fix incorrect include/config/auto.conf generation when Kconfig
   creates it along with the .config file

 - remove misleading $(AS) from documents

 - clean up precious tag files by distclean instead of mrproper

 - add a new coccinelle patch for devm_platform_ioremap_resource
   migration

 - refactor module-related scripts to read modules.order instead of
   $(MODVERDIR)/*.mod files to get the list of created modules

 - remove MODVERDIR

 - update list of header compile-test

 - add -fcf-protection=none flag to avoid conflict with the retpoline
   flags when CONFIG_RETPOLINE=y

 - misc cleanups

* tag 'kbuild-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
  kbuild: add -fcf-protection=none when using retpoline flags
  kbuild: update compile-test header list for v5.3-rc1
  kbuild: split out *.mod out of {single,multi}-used-m rules
  kbuild: remove 'prepare1' target
  kbuild: remove the first line of *.mod files
  kbuild: create *.mod with full directory path and remove MODVERDIR
  kbuild: export_report: read modules.order instead of .tmp_versions/*.mod
  kbuild: modpost: read modules.order instead of $(MODVERDIR)/*.mod
  kbuild: modsign: read modules.order instead of $(MODVERDIR)/*.mod
  kbuild: modinst: read modules.order instead of $(MODVERDIR)/*.mod
  scsi: remove pointless $(MODVERDIR)/$(obj)/53c700.ver
  kbuild: remove duplication from modules.order in sub-directories
  kbuild: get rid of kernel/ prefix from in-tree modules.{order,builtin}
  kbuild: do not create empty modules.order in the prepare stage
  coccinelle: api: add devm_platform_ioremap_resource script
  kbuild: compile-test headers listed in header-test-m as well
  kbuild: remove unused hostcc-option
  kbuild: remove tag files by distclean instead of mrproper
  kbuild: add --hash-style= and --build-id unconditionally
  kbuild: get rid of misleading $(AS) from documents
  ...

Pull dcache and mountpoint updates from Al Viro:
 "Saner handling of refcounts to mountpoints.

  Transfer the counting reference from struct mount ->mnt_mountpoint
  over to struct mountpoint ->m_dentry. That allows us to get rid of the
  convoluted games with ordering of mount shutdowns.

  The cost is in teaching shrink_dcache_{parent,for_umount} to cope with
  mixed-filesystem shrink lists, which we'll also need for the Slab
  Movable Objects patchset"

* 'work.dcache2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  switch the remnants of releasing the mountpoint away from fs_pin
  get rid of detach_mnt()
  make struct mountpoint bear the dentry reference to mountpoint, not struct mount
  Teach shrink_dcache_parent() to cope with mixed-filesystem shrink lists
  fs/namespace.c: shift put_mountpoint() to callers of unhash_mnt()
  __detach_mounts(): lookup_mountpoint() can't return ERR_PTR() anymore
  nfs: dget_parent() never returns NULL
  ceph: don't open-code the check for dead lockref

The recent fix for CR2 corruption introduced a new way to reliably corrupt
the saved CR2 value.

CR2 is saved early in the entry code in RDX, which is the third argument to
the fault handling functions. But it missed that between saving and
invoking the fault handler enter_from_user_mode() can be called. RDX is a
caller saved register so the invoked function can freely clobber it with
the obvious consequences.

The TRACE_IRQS_OFF call is safe as it calls through the thunk which
preserves RDX, but TRACE_IRQS_OFF_DEBUG is not because it also calls into
C-code outside of the thunk.

Store CR2 in R12 instead which is a callee saved register and move R12 to
RDX just before calling the fault handler.

Fixes: a0d14b89 ("x86/mm, tracing: Fix CR2 corruption")
Reported-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907201020540.1782@nanos.tec.linutronix.de

It's clearly documented that smp function calls cannot be invoked from
softirq handling context. Unfortunately nothing enforces that or emits a
warning.

A single function call can be invoked from softirq context only via
smp_call_function_single_async().

The only legit context is task context, so add a warning to that effect.
Reported-by: Nluferry <luferry@163.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190718160601.GP3402@hirez.programming.kicks-ass.net

Updates KVM_CAP_PMU_EVENT_FILTER so it can also whitelist or blacklist
fixed counters.
Signed-off-by: NEric Hankland <ehankland@google.com>
[No need to check padding fields for zero. - Paolo]
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>