When ae_dev doesn't support DCB, rx_priv_wl_config,
common_thrd_config and tm_qs_bp_cfg can't be called, otherwise
cmd return fail, which causes the hclge module initialization
process to fail.
This patch fix it by adding a DCB capability flag to check if
the ae_dev support DCB.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add the ROCE supported flag in the driver_data
field of pci_device_id, delete roce_pci_tbl and change
HNAE_DEV_SUPPORT_ROCE_B to HNAE3_DEV_SUPPORT_ROCE_B.
This cleanup is done in order to support adding capability
in pci_device_id and to fix initialization failure when
cmd is not supported.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains two Netfilter fixes for your net tree,
they are:

1) Fix NAt compilation with UP, from Geert Uytterhoeven.

2) Fix incorrect number of entries when dumping a set, from
   Vishwanath Pai.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In isdn_ppp_write(), the header (i.e., protobuf) of the buffer is
fetched twice from userspace. The first fetch is used to peek at the
protocol of the message and reset the huptimer if necessary; while the
second fetch copies in the whole buffer. However, given that buf resides
in userspace memory, a user process can race to change its memory content
across fetches. By doing so, we can either avoid resetting the huptimer
for any type of packets (by first setting proto to PPP_LCP and later
change to the actual type) or force resetting the huptimer for LCP
packets.

This patch changes this double-fetch behavior into two single fetches
decided by condition (lp->isdn_device < 0 || lp->isdn_channel <0).
A more detailed discussion can be found at
https://marc.info/?l=linux-kernel&m=150586376926123&w=2Signed-off-by: NMeng Xu <mengxu.gatech@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fec_ptp_check_pps_event will return 1 if FEC_T_TF_MASK caused
an interrupt. Don't return IRQ_NONE in this case.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FEC_ENET_TS_TIMER is not checked in the interrupt routine
so there is no need to enable it.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before queue 0 was always checked if any queue caused an interrupt.
It is better to just mark queue 0 if queue 0 has caused an interrupt.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Acked-by: NFugang Duan <Fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since XDP's view of the packet includes the MAC header, moving the start-
 of-packet with bpf_xdp_adjust_head needs to also update the offset of the
 MAC header (which is relative to skb->head, not to the skb->data that was
 changed).
Without this, tcpdump sees packets starting from the old MAC header rather
 than the new one, at least in my tests on the loopback device.

Fixes: b5cdae32 ("net: Generic XDP")
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The actual length of cmsg fetched in during the second loop
(i.e., kcmsg - kcmsg_base) could be different from what we
get from the first loop (i.e., kcmlen).

The main reason is that the two get_user() calls in the two
loops (i.e., get_user(ucmlen, &ucmsg->cmsg_len) and
__get_user(ucmlen, &ucmsg->cmsg_len)) could cause ucmlen
to have different values even they fetch from the same userspace
address, as user can race to change the memory content in
&ucmsg->cmsg_len across fetches.

Although in the second loop, the sanity check
if ((char *)kcmsg_base + kcmlen - (char *)kcmsg < CMSG_ALIGN(tmp))
is inplace, it only ensures that the cmsg fetched in during the
second loop does not exceed the length of kcmlen, but not
necessarily equal to kcmlen. But indicated by the assignment
kmsg->msg_controllen = kcmlen, we should enforce that.

This patch adds this additional sanity check and ensures that
what is recorded in kmsg->msg_controllen is the actual cmsg length.
Signed-off-by: NMeng Xu <mengxu.gatech@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a bug exhibited by the following scenario:
  1. fd1 = perf_event_open with attr.config = ID1
  2. attach bpf program prog1 to fd1
  3. fd2 = perf_event_open with attr.config = ID1
     <this will be successful>
  4. user program closes fd2 and prog1 is detached from the tracepoint.
  5. user program with fd1 does not work properly as tracepoint
     no output any more.

The issue happens at step 4. Multiple perf_event_open can be called
successfully, but only one bpf prog pointer in the tp_event. In the
current logic, any fd release for the same tp_event will free
the tp_event->prog.

The fix is to free tp_event->prog only when the closing fd
corresponds to the one which registered the program.
Signed-off-by: NYonghong Song <yhs@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packet socket bind operations must hold the po->bind_lock. This keeps
po->running consistent with whether the socket is actually on a ptype
list to receive packets.

fanout_add unbinds a socket and its packet_rcv/tpacket_rcv call, then
binds the fanout object to receive through packet_rcv_fanout.

Make it hold the po->bind_lock when testing po->running and rebinding.
Else, it can race with other rebind operations, such as that in
packet_set_ring from packet_rcv to tpacket_rcv. Concurrent updates
can result in a socket being added to a fanout group twice, causing
use-after-free KASAN bug reports, among others.

Reported independently by both trinity and syzkaller.
Verified that the syzkaller reproducer passes after this patch.

Fixes: dc99f600 ("packet: Add fanout support.")
Reported-by: Nnixioaming <nixiaoming@huawei.com>
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, writing into
net.ipv6.conf.all.{accept_dad,use_optimistic,optimistic_dad} has no effect.
Fix handling of these flags by:

- using the maximum of global and per-interface values for the
  accept_dad flag. That is, if at least one of the two values is
  non-zero, enable DAD on the interface. If at least one value is
  set to 2, enable DAD and disable IPv6 operation on the interface if
  MAC-based link-local address was found

- using the logical OR of global and per-interface values for the
  optimistic_dad flag. If at least one of them is set to one, optimistic
  duplicate address detection (RFC 4429) is enabled on the interface

- using the logical OR of global and per-interface values for the
  use_optimistic flag. If at least one of them is set to one,
  optimistic addresses won't be marked as deprecated during source address
  selection on the interface.

While at it, as we're modifying the prototype for ipv6_use_optimistic_addr(),
drop inline, and let the compiler decide.

Fixes: 7fd2561e ("net: ipv6: Add a sysctl to make optimistic addresses useful candidates")
Signed-off-by: NMatteo Croce <mcroce@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f784ad3d ("ipv6: do not send RTM_DELADDR for tentative
addresses") incorrectly assumes that no RTM_NEWADDR are sent for
addresses in tentative state, as this does happen for the standard
IPv6 use-case of DAD failure, see the call to ipv6_ifa_notify() in
addconf_dad_stop(). So as a result of this change, no RTM_DELADDR is
sent after DAD failure for a link-local when strict DAD (accept_dad=2)
is configured, or on the next admin down in other cases. The absence
of this notification breaks backwards compatibility and causes problems
after DAD failure if this notification was being relied on. The
solution is to allow RTM_DELADDR to still be sent after DAD failure.

Fixes: f784ad3d ("ipv6: do not send RTM_DELADDR for tentative addresses")
Signed-off-by: NMike Manning <mmanning@brocade.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 109980b8 ("bpf: don't select potentially stale
ri->map from buggy xdp progs") passed the pointer to the prog
itself to be loaded into r4 prior on bpf_redirect_map() helper
call, so that we can store the owner into ri->map_owner out of
the helper.

Issue with that is that the actual address of the prog is still
subject to change when subsequent rewrites occur that require
slow path in bpf_prog_realloc() to alloc more memory, e.g. from
patching inlining helper functions or constant blinding. Thus,
we really need to take prog->aux as the address we're holding,
which also works with prog clones as they share the same aux
object.

Instead of then fetching aux->prog during runtime, which could
potentially incur cache misses due to false sharing, we are
going to just use aux for comparison on the map owner. This
will also keep the patchlet of the same size, and later check
in xdp_map_invalid() only accesses read-only aux pointer from
the prog, it's also in the same cacheline already from prior
access when calling bpf_func.

Fixes: 109980b8 ("bpf: don't select potentially stale ri->map from buggy xdp progs")
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is pretty much a carbon copy of
commit 3079c652 ("caif: Fix napi poll list corruption")
with "caif" replaced by "emac".

The commit d75b1ade ("net: less interrupt masking in NAPI")
breaks emac.

It is now required that if the entire budget is consumed when poll
returns, the napi poll_list must remain empty.  However, like some
other drivers emac tries to do a last-ditch check and if there is
more work it will call napi_reschedule and then immediately process
some of this new work.  Should the entire budget be consumed while
processing such new work then we will violate the new caller
contract.

This patch fixes this by not touching any work when we reschedule
in emac.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our recent change exposed a bug in TCP Fastopen Client that syzkaller
found right away [1]

When we prepare skb with SYN+DATA, we attempt to transmit it,
and we update socket state as if the transmit was a success.

In socket RTX queue we have two skbs, one with the SYN alone,
and a second one containing the DATA.

When (malicious) ACK comes in, we now complain that second one had no
skb_mstamp.

The proper fix is to make sure that if the transmit failed, we do not
pretend we sent the DATA skb, and make it our send_head.

When 3WHS completes, we can now send the DATA right away, without having
to wait for a timeout.

[1]
WARNING: CPU: 0 PID: 100189 at net/ipv4/tcp_input.c:3117 tcp_clean_rtx_queue+0x2057/0x2ab0 net/ipv4/tcp_input.c:3117()

 WARN_ON_ONCE(last_ackt == 0);

Modules linked in:
CPU: 0 PID: 100189 Comm: syz-executor1 Not tainted
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
 0000000000000000 ffff8800b35cb1d8 ffffffff81cad00d 0000000000000000
 ffffffff828a4347 ffff88009f86c080 ffffffff8316eb20 0000000000000d7f
 ffff8800b35cb220 ffffffff812c33c2 ffff8800baad2440 00000009d46575c0
Call Trace:
 [<ffffffff81cad00d>] __dump_stack
 [<ffffffff81cad00d>] dump_stack+0xc1/0x124
 [<ffffffff812c33c2>] warn_slowpath_common+0xe2/0x150
 [<ffffffff812c361e>] warn_slowpath_null+0x2e/0x40
 [<ffffffff828a4347>] tcp_clean_rtx_queue+0x2057/0x2ab0 n
 [<ffffffff828ae6fd>] tcp_ack+0x151d/0x3930
 [<ffffffff828baa09>] tcp_rcv_state_process+0x1c69/0x4fd0
 [<ffffffff828efb7f>] tcp_v4_do_rcv+0x54f/0x7c0
 [<ffffffff8258aacb>] sk_backlog_rcv
 [<ffffffff8258aacb>] __release_sock+0x12b/0x3a0
 [<ffffffff8258ad9e>] release_sock+0x5e/0x1c0
 [<ffffffff8294a785>] inet_wait_for_connect
 [<ffffffff8294a785>] __inet_stream_connect+0x545/0xc50
 [<ffffffff82886f08>] tcp_sendmsg_fastopen
 [<ffffffff82886f08>] tcp_sendmsg+0x2298/0x35a0
 [<ffffffff82952515>] inet_sendmsg+0xe5/0x520
 [<ffffffff8257152f>] sock_sendmsg_nosec
 [<ffffffff8257152f>] sock_sendmsg+0xcf/0x110

Fixes: 8c72c65b ("tcp: update skb->skb_mstamp more carefully")
Fixes: 783237e8 ("net-tcp: Fast Open client - sending SYN-data")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Salil Mehta says:

====================
Bug fixes for the HNS3 Ethernet Driver for Hip08 SoC

This patch set presents some bug fixes for the HNS3 Ethernet driver identified
during internal testing & stabilization efforts.

Change Log:
Patch V2: Resolved comments from Leon Romanovsky
Patch V1: Initial Submit
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When register/unregister ae_dev, ae_dev should match all client
in the client_list. Enet and roce can co-exists together so we
should continue checking for enet and roce presence together.
So break should not be there.

Above caused problems in loading and unloading of modules.

Fixes: 38eddd126772 ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there is no vlan id in the packets, hardware will treat the vlan id
as 0 and look for the mac_vlan table. This patch set the default vlan id
of PF as 0. Without this config, it will fail when look for mac_vlan
table, and hardware will drop packets.

Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: NMingguang Qu <qumingguang@huawei.com>
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the ethernet address copy instance with more
appropriate ether_addr_copy() function.

Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the initialization of MAC address, fetched from HNS3
firmware i.e. when it is not randomly generated, to the HNS3 hardware.

Fixes: ca60906d2795 ("net: hns3: Add support of HNS3 Ethernet Driver for
hip08 SoC")
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the vector-to-ring map and unmap command and adds
INT_GL(for, Gap Limiting Interrupts) and VF id to it as required
by the hardware interface.

Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NMingguang Qu <qumingguang@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the IMP command being used to unmap the vector
from the corresponding ring.

Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Default phy address of every port is 0. Therefore, phy address for
each port need to be fetched from firmware and device initialized
with fetched non-default phy address.

Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

syzkaller reported following splat [1]

Since hard irq are disabled by the caller, bpf_map_free_id()
should not try to enable/disable BH.

Another solution would be to change htab_map_delete_elem() to
defer the free_htab_elem() call after
raw_spin_unlock_irqrestore(&b->lock, flags), but this might be not
enough to cover other code paths.

[1]
WARNING: CPU: 1 PID: 8052 at kernel/softirq.c:161 __local_bh_enable_ip
+0x1e/0x160 kernel/softirq.c:161
Kernel panic - not syncing: panic_on_warn set ...

CPU: 1 PID: 8052 Comm: syz-executor1 Not tainted 4.13.0-next-20170915+
#23
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:16 [inline]
 dump_stack+0x194/0x257 lib/dump_stack.c:52
 panic+0x1e4/0x417 kernel/panic.c:181
 __warn+0x1c4/0x1d9 kernel/panic.c:542
 report_bug+0x211/0x2d0 lib/bug.c:183
 fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:178
 do_trap_no_signal arch/x86/kernel/traps.c:212 [inline]
 do_trap+0x260/0x390 arch/x86/kernel/traps.c:261
 do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:298
 do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:311
 invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905
RIP: 0010:__local_bh_enable_ip+0x1e/0x160 kernel/softirq.c:161
RSP: 0018:ffff8801cdcd7748 EFLAGS: 00010046
RAX: 0000000000000082 RBX: 0000000000000201 RCX: 0000000000000000
RDX: 1ffffffff0b5933c RSI: 0000000000000201 RDI: ffffffff85ac99e0
RBP: ffff8801cdcd7758 R08: ffffffff85b87158 R09: 1ffff10039b9aec6
R10: ffff8801c99f24c0 R11: 0000000000000002 R12: ffffffff817b0b47
R13: dffffc0000000000 R14: ffff8801cdcd77e8 R15: 0000000000000001
 __raw_spin_unlock_bh include/linux/spinlock_api_smp.h:176 [inline]
 _raw_spin_unlock_bh+0x30/0x40 kernel/locking/spinlock.c:207
 spin_unlock_bh include/linux/spinlock.h:361 [inline]
 bpf_map_free_id kernel/bpf/syscall.c:197 [inline]
 __bpf_map_put+0x267/0x320 kernel/bpf/syscall.c:227
 bpf_map_put+0x1a/0x20 kernel/bpf/syscall.c:235
 bpf_map_fd_put_ptr+0x15/0x20 kernel/bpf/map_in_map.c:96
 free_htab_elem+0xc3/0x1b0 kernel/bpf/hashtab.c:658
 htab_map_delete_elem+0x74d/0x970 kernel/bpf/hashtab.c:1063
 map_delete_elem kernel/bpf/syscall.c:633 [inline]
 SYSC_bpf kernel/bpf/syscall.c:1479 [inline]
 SyS_bpf+0x2188/0x46a0 kernel/bpf/syscall.c:1451
 entry_SYSCALL_64_fastpath+0x1f/0xbe

Fixes: f3f1c054 ("bpf: Introduce bpf_map ID")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: NMartin KaFai Lau <kafai@fb.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clarify that rhashtable_walk_{stop,start} will not reset the iterator to
the beginning of the hash table.  Confusion between rhashtable_walk_enter
and rhashtable_walk_start has already lead to a bug.
Signed-off-by: NAndreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the integration of PHYLINK, the configuration option which
used to be under the PHY infrastructure menu in menuconfig ended
up one level up (the network device driver section)

By placing PHYLINK option right after PHYLIB entry, it broke the
way Kconfig used to build the menu. See kconfig-language.txt, section
"Menu structure", 2nd method.

This is fixed by placing the PHYLINK option just before PHYLIB.

Fixes: 9525ae83 ("phylink: add phylink infrastructure")
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2017-11-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just two netlink fixes, both allowing privileged users
to crash the kernel with malformed netlink messages.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove Yuval from maintaining the bnx2x & qed* modules as he is no longer
working for the company. Thanks Yuval for your huge contributions and
tireless efforts over the many years and various companies.

Ariel
Signed-off-by: NAriel Elior <aelior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are several problems with commit 10377ba7 ("net: systemport:
Support 64bit statistics", first one got fixed in 7095c973 ("net:
systemport: Fix 64-bit stats deadlock").

The second problem is that this specific code updates the
stats64.tx_{packets,bytes} from ndo_get_stats64() and that is what we
are returning to ethtool -S. If we are not running a tool that involves
calling ndo_get_stats64(), then we won't get updated ethtool stats.

The solution to this is to update the stats from both call sites,
factoring that into a specific function, While at it, don't just check
the sizeof() but also the type of the statistics in order to use the
64-bit stats seqlock.

Fixes: 10377ba7 ("net: systemport: Support 64bit statistics")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems we have to be more careful in napi_complete_done()
use. This patch is not a revert, as it seems we can
avoid bug that Ville reported by moving the napi_complete_done()
test in the spinlock section.

Many thanks to Ville for detective work and all tests.

Fixes: 617f0121 ("8139too: use napi_complete_done()")
Reported-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

remove tcp_may_send_now and tcp_snd_test that are no longer used

Fixes: 840a3cbe ("tcp: remove forward retransmit feature")
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If bpf_map_precharge_memlock in dev_map_alloc, -ENOMEM is returned
regardless of the actual error produced by bpf_map_precharge_memlock.
Fix it by passing on the error returned by bpf_map_precharge_memlock.

Also return -EINVAL instead of -ENOMEM if the page count overflow check
fails.

This makes dev_map_alloc match the behavior of other bpf maps' alloc
functions wrt. return values.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check for ingress-only qdisc for flower offload, as other qdiscs
are not supported for flower offload.
Suggested-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix ASCII art in Documentation/networking/switchdev.txt:

Change non-ASCII "spaces" to ASCII spaces.

Change 2 erroneous '+' characters in ASCII art to '-' (at the '*'
characters below):

line 32:
                     +--+----+----+----+-*--+----+---+  +-----+-----+
line 41:
                     +--------------+---*------------+
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Acked-by: NPavel Machek <pavel@ucw.cz>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this script, edited from Linux Advanced Routing and Traffic Control guide

tc q a dev en0 root handle 1: htb default a
tc c a dev en0 parent 1:  classid 1:1 htb rate 6mbit burst 15k
tc c a dev en0 parent 1:1 classid 1:a htb rate 5mbit ceil 6mbit burst 15k
tc c a dev en0 parent 1:1 classid 1:b htb rate 1mbit ceil 6mbit burst 15k
tc f a dev en0 parent 1:0 prio 1 $clsname $clsargs classid 1:b
ping $address -c1
tc -s c s dev en0

classifies traffic to 1:b or 1:a, depending on whether the packet matches
or not the pattern $clsargs of filter $clsname. However, when $clsname is
'matchall', a systematic crash can be observed in htb_classify(). HTB and
classful qdiscs don't assign initial value to struct tcf_result, but then
they expect it to contain valid values after filters have been run. Thus,
current 'matchall' ignores the TCA_MATCHALL_CLASSID attribute, configured
by user, and makes HTB (and classful qdiscs) dereference random pointers.

By assigning head->res to *res in mall_classify(), before the actions are
invoked, we fix this crash and enable TCA_MATCHALL_CLASSID functionality,
that had no effect on 'matchall' classifier since its first introduction.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1460213Reported-by: NJiri Benc <jbenc@redhat.com>
Fixes: b87f7936 ("net/sched: introduce Match-all classifier")
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Acked-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If ipv6 has been disabled from cmdline since kernel started, it makes
no sense to allow users to create any ip6 tunnel. Otherwise, it could
some potential problem.

Jianlin found a kernel crash caused by this in ip6_gre when he set
ipv6.disable=1 in grub:

[  209.588865] Unable to handle kernel paging request for data at address 0x00000080
[  209.588872] Faulting instruction address: 0xc000000000a3aa6c
[  209.588879] Oops: Kernel access of bad area, sig: 11 [#1]
[  209.589062] NIP [c000000000a3aa6c] fib_rules_lookup+0x4c/0x260
[  209.589071] LR [c000000000b9ad90] fib6_rule_lookup+0x50/0xb0
[  209.589076] Call Trace:
[  209.589097] fib6_rule_lookup+0x50/0xb0
[  209.589106] rt6_lookup+0xc4/0x110
[  209.589116] ip6gre_tnl_link_config+0x214/0x2f0 [ip6_gre]
[  209.589125] ip6gre_newlink+0x138/0x3a0 [ip6_gre]
[  209.589134] rtnl_newlink+0x798/0xb80
[  209.589142] rtnetlink_rcv_msg+0xec/0x390
[  209.589151] netlink_rcv_skb+0x138/0x150
[  209.589159] rtnetlink_rcv+0x48/0x70
[  209.589169] netlink_unicast+0x538/0x640
[  209.589175] netlink_sendmsg+0x40c/0x480
[  209.589184] ___sys_sendmsg+0x384/0x4e0
[  209.589194] SyS_sendmsg+0xd4/0x140
[  209.589201] SyS_socketcall+0x3e0/0x4f0
[  209.589209] system_call+0x38/0xe0

This patch is to return -EOPNOTSUPP in ip6_tunnel_init if ipv6 has been
disabled from cmdline.
Reported-by: NJianlin Shi <jishi@redhat.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To clear Speed Selection in MDIO control register(0x10),
ie, clear bits 6 and 13 to zero while keeping other bits same.
Before AND operation,The Mask value has to be perform with bitwise NOT
operation (ie, ~ operator)

This patch clears current speed selection before writing the
new speed settings to gmii2rgmii converter

Fixes: f411a616 ("net: phy: Add gmiitorgmii converter support")
Signed-off-by: NFahad Kunnathadi <fahad.kunnathadi@dexceldesigns.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now in ip6gre_header before packing the ipv6 header, it skb_push t->hlen
which only includes encap_hlen + tun_hlen. It means greh and inner header
would be over written by ipv6 stuff and ipv6h might have no chance to set
up.

Jianlin found this issue when using remote any on ip6_gre, the packets he
captured on gre dev are truncated:

22:50:26.210866 Out ethertype IPv6 (0x86dd), length 120: truncated-ip6 -\
8128 bytes missing!(flowlabel 0x92f40, hlim 0, next-header Options (0)  \
payload length: 8192) ::1:2000:0 > ::1:0:86dd: HBH [trunc] ip-proto-128 \
8184

It should also skb_push ipv6hdr so that ipv6h points to the right position
to set ipv6 stuff up.

This patch is to skb_push hlen + sizeof(*ipv6h) and also fix some indents
in ip6gre_header.

Fixes: c12b395a ("gre: Support GRE over IPv6")
Reported-by: NJianlin Shi <jishi@redhat.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If TX rates are specified during mesh join, the channel must
also be specified. Check the channel pointer to avoid a null
pointer dereference if it isn't.
Reported-by: NJouni Malinen <j@w1.fi>
Fixes: 8564e382 ("cfg80211: add checks for beacon rate, extend to mesh")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>