USE_PM_CLK_RUNTIME_OPS is introduced so we don't repeat the same code
to do runtime_suspend and runtime_resume across users of PM clocks.
Use it to remove the boilerplate code.
Signed-off-by: NRajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: NKevin Hilman <khilman@linaro.org>
Acked-by: NSantosh Shilimkar <ssantosh@kernel.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

USE_PM_CLK_RUNTIME_OPS is introduced so we don't repeat the same code
to do runtime_suspend and runtime_resume across users of PM clocks.
Use it to remove the boilerplate code.
Signed-off-by: NRajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: NKevin Hilman <khilman@linaro.org>
Acked-by: NSantosh Shilimkar <ssantosh@kernel.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.

So Suspend-to-RAM and Suspend-to-idle are failing on Exynos5250 Snow.

Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Remove the extra zero in the "cpu-crit-0" trip point for exynos5420
and exynos5440.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The Exynos4412 SoC has a s3c6410 RTC where the source clock
is now a mandatory property.
This patch fixes probe failure of s3c-rtc on Odroid-X2/U2/U3 boards.
Signed-off-by: NMarkus Reichl <m.reichl@fivetechno.de>
Tested-by: NTobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Commit ea08de16 ("ARM: dts: Add DISP1 power domain for exynos5420")
added a device node for the Exynos5420 DISP1 power domain but dit not
make the DP controller a consumer of that power domain.

This causes an "Unhandled fault: imprecise external abort" error if the
exynos-dp driver tries to access the DP controller registers and the PD
was turned off. This lead to a kernel panic and a complete system hang.

Make the DP controller device node a consumer of the DISP1 power domain
to ensure that the PD is turned on when the exynos-dp driver is probed.

Fixes: ea08de16 ("ARM: dts: Add DISP1 power domain for exynos5420")
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Select IMX50, IMX6SX and LS1021A SoC support.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Make sure that xen_swiotlb_init allocates buffers that are DMA capable
when at least one memblock is available below 4G. Otherwise we assume
that all devices on the SoC can cope with >4G addresses. We do this on
ARM and ARM64, where dom0 is mapped 1:1, so pfn == mfn in this case.

No functional changes on x86.

From: Chen Baozi <baozich@gmail.com>
Signed-off-by: NChen Baozi <baozich@gmail.com>
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: NChen Baozi <baozich@gmail.com>
Acked-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

The L3 Error handling on OMAP5 for the most part is very similar
to that of OMAP4, and had leveraged common data structures and
register layout definitions so far. Upon closer inspection, there
are a few minor differences causing an incorrect decoding and
reporting of the master NIU upon an error:

  1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies
     11 bits on OMAP5 as against 8 bits on OMAP4, with the master
     NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR
     field.
  2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3
     input sources on OMAP5. The common DEBUGSS source is at a
     different input on each SoC.

Fix the above issues by using a OMAP5-specific compatible property
and using SoC-specific data where there are differences.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix a typo in DRA7 dtsi where 12 bytes are needed for register
description of ABB efuse registers, however only 8 bytes are provided
to map. For some weird reason, this does not generate abort at offset
0x8, probably due to default maps already provided in io.c for the bus
register ranges.
Reported-by: NMatt Gessner <Matt.Gessner@windriver.com>
Reported-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

BeagleBoard-X15 pre-production change includes switching the GPIO fan
gpio over from 1 to 2 to allow for a potential fix at a later point in
time for USB client VBUS detection using PMIC VBUS detect capability.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

BeagleBoard-X15 pre-production change includes switching over to UART
pins that now allow for UART download capability. All original boards
should either have been returned for modifications or already modified
for the required change and maintaining compatibility for older boards
are no longer needed.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The new AM437x SK Beta boards have removed the
large capacitors on the gpio-matrix column lines
which means we can reduce col-scan-delay-us to 5us
without loosing functionality.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

AM437x Starter Kit uses a NewHaven Display module with
a 4.3" display and EDT FT5306 touchscreen

On that module's new revision, NewHave decided to change
the pinout on the 6 pin flat-pcb touchscreen connector so
that instead of having WAKE pin, we now have RESETn.

The new display module is available on AM437x SK Beta and
all new revisions while the older revision is only available
on AM437x SK Alpha which, unfortunately, can't be supported
anymore in mainline without a revert of this patch.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With commit bc078316 ("ARM: dts: DRA7: Add node for RTC"), we now
have AM57xx RTC register itself as alias 0 even before DS1307 or TPS
rtc drivers are loaded up. However, since neither TPS, nor AM57xx RTC
are capable of being backedup by battery, we would like to maintain
the "primary" rtc as mcp79410 rtc device.

This also generates the following warnings in the bootlog highlighting
the issue:
[    5.895445] rtc-ds1307 2-006f: /aliases ID 0 not available
...
[    6.476285] palmas-rtc 48070000.i2c:tps659038@58:tps659038_rtc: /aliases ID 1 not available

So, add proper aliases to ensure that RTC order is always consistent
to userspace immaterial of probe order.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The interrupt polarity provided in devicetree is used to configure
the interrupt controller(ARM GIC), however, it seems that we have an
inverter at the GIC boundary inside AM57xx which inverts the signal
input from sys_irq external interrupt source.

Further, as per GIC distributor TRM,
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438d/BGBHIACJ.html#BABJFCFB
ARM GIC distributor does not support IRQ trigger type
IRQ_TYPE_LEVEL_LOW, and only rising or level high signals.

However, for some reason, the current configuration(which gets ignored
by GIC driver) functions on some platforms, however, on few platforms
results in infinite interrupts hogging the system down.

Switch over to rising edge for GIC configuration which is also aligned
with trigger point from the RTC chip and the internal inversion.

Fixes: 5a0f93c6 ("ARM: dts: Add am57xx-beagle-x15")
Signed-off-by: NGrygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add missing #iommu-cells property to the isp and iva iommu nodes. This
fixes the binding (property is required according to the generic iommu
binding) and removes the following kernel warning triggered once the
iommu nodes are referenced:

[    0.647521] /ocp/isp@480bc000: could not get #iommu-cells for /ocp/mmu@480bd400
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We need to enable EXTCON_USB_GPIO_USB and not
EXTCON_GPIO_USB.

Fixes: c08a54c0 ("ARM: omap2plus_defconfig: Enable EXTCON_GPIO_USB")
Reported-by: NNishant Menon <nm@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by-by: Nishanth Menon <nm@ti.com
Tested-by: Nishanth Menon <nm@ti.com
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

N900 audio recording needs that codec provides bias voltage for integrated
digital microphone and headset microphone depending which one is used.
Digital microphone uses 2 V bias and it comes from the codec A part. Codec
B part drives the headset microphone bias and that is set to 2.5 V.

Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: NPavel Machek <pavel@ucw.cz>
[Jarkko: Headset mic bias changed to 2 (2.5 V) as it was before commit
e2e8bfdf ("ASoC: tlv320aic3x: Convert mic bias to a supply widget")]
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

If we use a combination of VMODE and I2C4 for retention modes,
eventually the off idle power consumption will creep up by about
23mW, even during off mode with I2C4 always staying enabled.

Turns out this is because of erratum i531 "Extra Power Consumed
When Repeated Start Operation Mode Is Enabled on I2C Interface
Dedicated for Smart Reflex (I2C4)" as pointed out by Nishanth
Menon <nm@ti.com>.

Let's fix the issue by adding i2c_cfg_clear_mask for the bits
to clear when initializing the I2C4 adapter so we can clear
SREN bit that drives the I2C4 lines low otherwise when there
is no traffic.

Fixes: 3b8c4ebb ("ARM: OMAP3: Fix idle mode signaling for
Cc: stable@vger.kernel.org # v3.16+
sys_clkreq and sys_off_mode")
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Reviewed-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With commit 9fd85eb5 ("ARM: pmu: add support for interrupt-affinity
property"), we print a warning when we find a PMU SPI with a missing
missing interrupt-affinity property in a pmu node. Unfortunately, we
pass the wrong (NULL) device node to of_node_full_name, resulting in
unhelpful messages such as:

 hw perfevents: Failed to parse <no-node>/interrupt-affinity[0]

This patch fixes the name to that of the pmu node.

Fixes: 9fd85eb5 (ARM: pmu: add support for interrupt-affinity property)
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

PPIs are affine by nature, so the interrupt-affinity property is not
used and therefore we shouldn't print a warning in its absence.
Reported-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

bf35706f ("ARM: 8314/1: replace PROCINFO embedded branch with
relative offset") broke booting for Kirkwood. The kernel would say:

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

Error: unrecognized/unsupported processor variant (0x56251311).

Fix it by removing the extraneous .long __feroceon_setup from the
feroceon_proc_info macro.

Fixes: bf35706f ("ARM: 8314/1: replace PROCINFO embedded branch with relative offset")
Reported-by: NFlorian Fainelli <f.fainelli@gmail.com>
Suggested-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The block could never be compiled;  CPU_ICACHE_STREAMING_DISABLE has not
been defined in Kconfig since the very first Git commit.  Hence, we can
safely remove the entire block.
Signed-off-by: NValentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

CPU_ARM1020_CPU_IDLE is not defined in Kconfig.  The last reference on
LKML dates back to 2001, so we can safely remove the comments to make
static analysis tools happy.
Signed-off-by: NValentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch 22b3c181 ("arm: dma-mapping: limit
IOMMU mapping size") added a check for IO address space size. However
this patch broke IOMMU initialization for typical platforms initialized
from device tree, which get the default IO address space size of 4GiB.
This value doesn't fit into size_t and fails a check introduced by that
commit resulting in failed dma-mapping/iommu initialization. This patch
fixes this issue by adding proper support for full 4GiB address space
size.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The adv7511 IRQ is low level triggered, not falling edge triggered. The
wrong sense configuration results in no interrupt being triggered at
all, breaking hotplug detection. Fix it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Fixes: 83a0731b ("ARM: shmobile: koelsch: Add DU HDMI output support")
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

As the interrupt handling was transferred to the pxa_cplds driver,
make the switch in lubbock platform code.

Fixes: 157d2644 ("ARM: pxa: change gpio to platform device")
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NArnd Bergmann <arnd@arndb.de>

As the interrupt handling was transferred to the pxa_cplds driver,
make the switch in mainstone platform code.

Fixes: 157d2644 ("ARM: pxa: change gpio to platform device")
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Historically, this support was in arch/arm/mach-pxa/lubbock.c and
arch/arm/mach-pxa/mainstone.c. When gpio-pxa was moved to drivers/pxa,
it became a driver, and its initialization and probing happened at
postcore initcall. The lubbock code used to install the chained lubbock
interrupt handler at init_irq() time.

The consequence of the gpio-pxa change is that the installed chained irq
handler lubbock_irq_handler() was overwritten in pxa_gpio_probe(_dt)(),
removing :
 - the handler
 - the falling edge detection setting of GPIO0, which revealed the
   interrupt request from the lubbock IO board.

As a fix, move the gpio0 chained handler setup to a place where we have
the guarantee that pxa_gpio_probe() was called before, so that lubbock
handler becomes the true IRQ chained handler of GPIO0, demuxing the
lubbock IO board interrupts.

This patch moves all that handling to a mfd driver. It's only purpose
for the time being is the interrupt handling, but in the future it
should encompass all the motherboard CPLDs handling :
 - leds
 - switches
 - hexleds

The same logic applies to mainstone board.

Fixes: 157d2644 ("ARM: pxa: change gpio to platform device")
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The pinctrl-assert-gpios is an invalid pinctrl property.  It was
probably sneaked from vendor tree.  Remove it.

Fixes: 4e18a224 ("ARM: imx6qdl-sabreauto.dtsi: add max7310 support")
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Fix a typo in the TX DMA interrupt name for AUART4.
This patch makes AUART4 operational again.
Signed-off-by: NMarek Vasut <marex@denx.de>
Fixes: f30fb03d ("ARM: dts: add generic DMA device tree binding for mxs-dma")
Cc: stable@vger.kernel.org
Acked-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The property '#pwm-cells' is currently missing. It is not possible to
use pwm4 without this property.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Fixes: 5658a68f ("ARM i.MX25: Add devicetree")
Cc: <stable@vger.kernel.org>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The fixed-regulator bindings require a separate property enable-active-high,
the standard gpio phandle property polarity setting is ignored.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Fixes: 4fe69a93 ("ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/Solo")
Cc: stable@vger.kernel.org
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

My Pengutronix address is not valid anymore, redirect people to the Pengutronix
kernel team.
Reported-by: NHarald Geyer <harald@ccbib.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NRobert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The dr_mode of usb0 on imx233-olinuxino is left to default "otg".
Since the green LED (GPIO2_1) on imx233-olinuxino is connected to the
same pin as USB_OTG_ID it's possible to disable USB host by LED toggling:

echo 0 > /sys/class/leds/green/brightness
[ 1068.890000] ci_hdrc ci_hdrc.0: remove, state 1
[ 1068.890000] usb usb1: USB disconnect, device number 1
[ 1068.920000] usb 1-1: USB disconnect, device number 2
[ 1068.920000] usb 1-1.1: USB disconnect, device number 3
[ 1069.070000] usb 1-1.2: USB disconnect, device number 4
[ 1069.450000] ci_hdrc ci_hdrc.0: USB bus 1 deregistered
[ 1074.460000] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11

This patch fixes the issue by setting dr_mode to "host" in the dts file.
Reported-by: NHarald Geyer <harald@ccbib.org>
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Acked-by: NPeter Chen <peter.chen@freescale.com>
Fixes: b4931294 ("ARM: dts: imx23-olinuxino: Add USB host support")
Cc: stable@vger.kernel.org
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

On imx23-olinuxino the LED turns on when level logic high is aplied to
GPIO2_1.

Fix the gpios property accordingly.

Fixes: b34aa185 ("ARM: dts: imx23-olinuxino: Remove unneeded "default-on"")
Reported-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Tested-by: NStefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

There is no crystal connected to the internal RTC on the Open Block
AX3. So let's disable it in order to prevent the kernel probing the
driver uselessly. Eventually this patches removes the following
warning message from the boot log:
"rtc-mv d0010300.rtc: internal RTC not ticking"
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8 +

Fixes: c94a4ab7 ("ARM: ux500: Disable the MMCI gpio-regulator by default")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Fixes: c94a4ab7 ("ARM: ux500: Disable the MMCI gpio-regulator by default")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>