This patch uncomment a few lines that survived the RFCs.
However, there is not much to worry about, since AP mode is
not officially advertised and supported.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otus uses slightly different set of "Minimum MPDU Start Spacing" values
than the 802.11n D2.0 specifies. (the whole table is shifted by one and
therefore the 16us spacing is not officially available!)

And while we're at it, we also initialize our MAC's density register.
So, this annoying _feature_ will not break TX A-MPDU later.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to the use of a _REQ_DIRECT_PROBE bit, which is
unnecessary (and I wonder why it was done that way),
an interesting situation can arise:
 1) we try to probe an access point
 2) the AP doesn't response in time
 3) we tell userspace that we gave up
 4) the AP suddenly responds
 5) we auth/assoc with the AP

I've seen 4) happen in testing with hostapd SIGSTOPped,
and when SIGCONTinued it processes the probe requests
that came in and send responses. But 5) is not supposed
to happen after we tell everybody we've given up on the
AP.

To fix this, remove the _REQ_DIRECT_PROBE request bit,
and process probe responses when we're in the relevant
MLME state, namely IEEE80211_STA_MLME_DIRECT_PROBE.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A typo slipped into my patch to configure beacon intervals
properly -- this warning is supposed to trigger when the
beacon interval is zero, not non-zero.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the direct probe times out, we need to send the authentication
timeout event to notify SME in the same way as we notify on timeout
with authentication frames since the direct probe is run as part of
the authentication attempt.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to later add tracing or verifications to the driver
calls mac80211 makes, this patch adds static inline wrappers
for all operations.

All calls are now written as

	drv_<op>(local, ...);

instead of

	local->ops-><op>(&local->hw, ...);

Where necessary, the wrappers also do existence checking and
return default values as appropriate.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.

This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.

NOTE: The hw.conf.beacon_int setting is retained for now due
      to drivers still using it -- I couldn't untangle all
      drivers, some are updated in this patch.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are some places marked
	/* XXX maybe racy? */
and they really are racy because there's no locking.

This patch reworks much of the scan code, and introduces proper
locking for the scan request as well as the internal scanning
(which is necessary for IBSS/managed modes). Helper functions
are added to call the scanning code whenever necessary. The
scan deferring is changed to simply queue the scanning work
instead of trying to start the scan in place, the scanning work
will then take care of the rest.

Also, currently when internal scans are requested for an interface
that is trying to associate, we reject such scans. This was not
intended, the mlme code has provisions to scan twice when it can't
find the BSS to associate with right away; this has never worked
properly. Fix this by not rejecting internal scan requests for an
interface that is associating.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the IBSS code wants to scan, but that fails, we can
get stuck in a situation where you can never scan again.
Fix this by properly notifying ourselves when the scan
request has failed.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kalle points out that max_sleep_interval is somewhat confusing
because the value is measured in beacon intervals, and not in
TU. Rename it to max_sleep_period to be consistent with things
like DTIM period that are also measured in beacon intervals.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When somebody changes the PS parameters while scanning
is in progress, we enable PS -- during the scan. This
is clearly not desirable, and we can just abort enabling
PS when scanning since when the scan finishes it will
be taken care of.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are a few problems in the IBSS code:
 a) it tries to activate interfaces that are down after scanning
 b) it crashes after scanning on an IBSS iface that isn't active
 c) since the ssid_len is used as a flag, need to make it visible
    only after all other settings are set, this helps protect
    against b)

For b), we get a system crash:

wlan0: Creating new IBSS network, BSSID ce:f9:88:76:1e:4d
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<...>] ieee80211_sta_find_ibss+0x294/0x37d [mac80211]
Call Trace:
 [<...>] ieee80211_ibss_notify_scan_completed+0x0/0x88 [mac80211]
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net_create() will be used by C/R to create fresh netns on restart.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NSerge Hallyn <serue@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

copy_net_ns() doesn't copy anything, it creates fresh netns, so
get/put of old netns isn't needed.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NSerge Hallyn <serue@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With this patch in place, I'm successfully able to use the netconsole
mechanism with the Calao USB-A9263 board, which uses the AT91SAM9263
CPU, which in terms of Ethernet controller is supported by the macb
driver.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
[haavard.skinnemoen@atmel.com: disable_irq() -> local_irq_save()]
[haavard.skinnemoen@atmel.com: convert to net_device_ops]
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should be very safe compared with full enabled, so I see
no reason why it shouldn't be done right away. As ECN can only
be negotiated if the SYN sending party is also supporting it,
somebody in the loop probably knows what he/she is doing. If
SYN does not ask for ECN, the server side SYN-ACK is identical
to what it is without ECN. Thus it's quite safe.

The chosen value is safe w.r.t to existing configs which
choose to currently set manually either 0 or 1 but
silently upgrades those who have not explicitly requested
ECN off.

Whether to just enable both sides comes up time to time but
unless that gets done now we can at least make the servers
aware of ECN already. As there are some known problems to occur
if ECN is enabled, it's currently questionable whether there's
any real gain from enabling clients as servers mostly won't
support it anyway (so we'd hit just the negative sides). After
enabling the servers and getting that deployed, the client end
enable really has some potential gain too.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based almost entirely upon a patch by Eric Dumazet.

The common case is to have num-tx-queues <= num_rx_queues
and even if num_tx_queues is larger it will not be significantly
larger.

Therefore, a subtraction loop is always going to be faster than
modulus.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Spotted a tiny ugliness in a recently posted patch. This patch cuts it out.

Jirka
Signed-off-by: NJiri Pirko <jpirko@redhat.com>

 drivers/net/ne2k-pci.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Doing it in reverse order causes uevent to be sent before
we have a MAC address, which confuses udev.
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 0ba25ff4 ("br2684: convert to
net_device_ops") inadvertently deleted the initialization of the net_dev
pointer in the br2684_dev structure, leading to crashes.  This patch
adds it back.
Reported-by: NMikko Vinni <mmvinni@yahoo.com>
Tested-by: NMikko Vinni <mmvinni@yahoo.com>
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kernel should only be using the high 16 bits of a kernel
generated priority. Filter priorities in all other cases only
use the upper 16 bits of the u32 'prio' field of 'struct tcf_proto',
but when the kernel generates the priority of a filter is saves all
32 bits which can result in incorrect lookup failures when a filter
needs to be deleted or modified.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlex Williamson <alex.williamson@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were avoiding calling sg_init* on scatterlists passed
into virtnet_send_command to prevent extraneous end markers.
This caused build warnings for uninitialized variables.
Cleanup the code to create proper scatterlists.
Signed-off-by: NAlex Williamson <alex.williamson@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

3c589_cs,3c574_cs,serial_cs:

 (1)add cis(firmware) of 3Com lan&modem mulitifunction pcmcia card.
 (2)load correct configuration register for 3Com card
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes the cleanup in bond_create nicer :) Also now the forgotten
free_netdev is called.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

virtio_net.h uses the macro ETH_ALEN which is defined in linux/if_ether.h.
Discovered when hacking on virtio-over-pci patches.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds new logic to support a clock gating feature found on the
latest set of chipsets. The clock gating is performed on the tx/rx
engines when the link is disconnected. Clock gating helps in reducing
power consumption.

* modified based on comments from netdev
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LAN9512 and LAN9514 are USB hubs with an integrated 10/100 ethernet
controller.  Logically this looks like an ethernet controller (similar
to LAN9500) permanently attached to one of the hub's downstream ports.

This patch adds the usb device id of the new ethernet controller to the
smsc95xx driver.  This id is the same in both new devices.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SMSC LAN9500 has dual purpose GPIO/LED pins, and by default at power-on
these are configured as GPIOs.  This means that if LEDs are fitted they
won't ever light.

This patch sets them to be LED outputs for speed, duplex and
link/activity.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When netconsole is loaded and a network interface fades away (e.g. on
rmmod $interface_driver_module) the rmmod remains stuck and some locks
are taken that prevent any additional module loading/unloading as well
as interface up/down changes.
In addition kernel logs (and console) get flooded at 10s interval with

[  122.464065] unregister_netdevice: waiting for eth0 to become free. Usage count = 1
[  132.704059] unregister_netdevice: waiting for eth0 to become free. Usage count = 1

This patch lets netconsole take NETDEV_UNREGISTER event into account
and release the affected interface if it was in use.
Signed-off-by: NBruno Prémont <bonbons@linux-vserver.org>
Acked-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

xt_socket can use connection tracking, and checks whether it is a module.
Signed-off-by: NLaszlo Attila Toth <panther@balabit.hu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.

Cc: netdev@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bond_slave_info_query() should keep a read lock while accessing slave info,
or risk accessing stale data and corruption.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial: fixing gcc 4.4 compiler warning:
drivers/net/cxgb3/t3_hw.c: In function ‘t3_prep_adapter’:
drivers/net/cxgb3/t3_hw.c:3782: warning: suggest parentheses around operand of ‘!’ or change ‘|’ to ‘||’ or ‘!’ to ‘~’
Signed-off-by: NSergey Senozhatsky <sergey.senozhatsky@mail.by>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>