If the new connection update parameter are accepted, the LE master
host sends the LE Connection Update Command to its controller informing
the new requested parameters.
Signed-off-by: NClaudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Use proper timer instead of hci command flow control to timeout
failed hci commands. Otherwise stack ends up sending commands
when flow control is used to block new commands.

2010-09-01 18:29:41.592132 < HCI Command: Remote Name Request (0x01|0x0019) plen 10
    bdaddr 00:16:CF:E1:C7:D7 mode 2 clkoffset 0x0000
2010-09-01 18:29:41.592681 > HCI Event: Command Status (0x0f) plen 4
    Remote Name Request (0x01|0x0019) status 0x00 ncmd 0
2010-09-01 18:29:51.022033 < HCI Command: Remote Name Request Cancel (0x01|0x001a) plen 6
    bdaddr 00:16:CF:E1:C7:D7
Signed-off-by: NVille Tervo <ville.tervo@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Bluetooth V4.0 adds support for Low Energy (LE) connections.
Specification introduces new set of hci commands to control LE
connection. This patch adds logic to create, cancel and disconnect
LE connections.
Signed-off-by: NVille Tervo <ville.tervo@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Add needed HCI command and event structs to
create LE connections.
Signed-off-by: NVille Tervo <ville.tervo@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds a new set_io_capability management command which is used
to set the IO capability for Secure Simple Pairing (SSP) as well as the
Security Manager Protocol (SMP). The value is per hci_dev and each
hci_conn object inherits it upon creation.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds the necessary commands and events needed to communicate
PIN code related actions between the kernel and userspace. This includes
a pin_code_request event as well as pin_code_reply and
pin_code_negative_reply commands.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds a management commands to feed the kernel with all stored
link keys as well as remove specific ones or all of them. Once the
load_keys command has been called the kernel takes over link key
replies. A new_key event is also added to inform userspace of newly
created link keys that should be stored permanently.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds the possibility for user space to fully control the
Class of Device value of local adapters. To control the service class
bits each UUID that's added comes with a service class "hint" which acts
as a mask of bits that the UUID needs to have enabled. The
set_service_cache management command is used to make sure we queue up
all UUID changes as user space initializes its drivers and then send a
single HCI_Write_Class_of_Device command when initialization is
complete.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Using the managment interface means that user space doesn't need to do
any HCI command sending at all. This patch moves the remaining
initialization commands from user space to the kernel side. The patch
makes use of the new feature of __hci_request which allows the request
to be dynamically modified while it is ongoing (something that is needed
to react appropriately to the local features and the version of the
adapter).
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The controller may have link keys in its own memory and these keys could
be used for secure connections. However, since the interface to access
these keys doesn't provide information about the key types (which would
be needed to infer the level of security each key provides) using these
keys is rather useless. Therefore, simply clear the controller side list
in the initialization procedure.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds the necessary logic to act accordingly when the
HCI_PAIRABLE flag is not set. In that case PIN code replies as well as
Secure Simple Pairing requests without a NoBonding requirement need to
be rejected.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch implements a new set_pairable management command to control
the pairable state of local adapters. The state is represented using a
new HCI_PAIRABLE flag in the hci_dev struct.

For backwards compatibility with older user space versions the
HCI_PAIRABLE flag gets automatically set when the existence of an
adapter is reported to user space through legacy methods and the
HCI_MGMT flag is not set.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds a HCI_MGMT flag to track adapters which are under the
control of the management interface. This is needed to make sure that
new kernels will work with old user space versions. I.e. behaviour which
could break old user space versions (but is needed by the management
interface) should not be exhibited when the HCI_MGMT flag is not set.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch implements automatic initialization of basic information
about newly registered Bluetooth adapters. E.g. the address and features
are always needed so it makes sense for the kernel to automatically
power on adapters and read this information. A new HCI_SETUP flag is
added to track this state.

In order to not consume unnecessary amounts of power if there isn't a
user space available that could switch the adapter back off, a timer is
added to do this automatically as long as no Bluetooth user space seems
to be present. A new HCI_AUTO_OFF flag is added that user space needs to
clear to avoid the automatic power off.

Additionally, the management interface index_added event is moved to the
end of the HCI_SETUP stage so a user space supporting the managment
inteface has all the necessary information available for fetching when
it gets notified of a new adapter. The HCI_DEV_REG event is kept in the
same place as before since existing HCI raw socket based user space
versions depend on seeing the kernels initialization sequence
(hci_init_req) to determine when the adapter is ready for use.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Modification of Nick Pelly <npelly@google.com> patch.

With Bluetooth 2.1 ACL packets can be flushable or non-flushable. This commit
makes ACL data packets non-flushable by default on compatible chipsets, and
adds the BT_FLUSHABLE socket option to explicitly request flushable ACL
data packets for a given L2CAP socket. This is useful for A2DP data which can
be safely discarded if it can not be delivered within a short time (while
other ACL data should not be discarded).

Note that making ACL data flushable has no effect unless the automatic flush
timeout for that ACL link is changed from its default of 0 (infinite).

Default packet types (for compatible chipsets):
Frame 34: 13 bytes on wire (104 bits), 13 bytes captured (104 bits)
Bluetooth HCI H4
Bluetooth HCI ACL Packet
    .... 0000 0000 0010 = Connection Handle: 0x0002
    ..00 .... .... .... = PB Flag: First Non-automatically Flushable Packet (0)
    00.. .... .... .... = BC Flag: Point-To-Point (0)
    Data Total Length: 8
Bluetooth L2CAP Packet

After setting BT_FLUSHABLE
(sock.setsockopt(274 /*SOL_BLUETOOTH*/, 8 /* BT_FLUSHABLE */, 1 /* flush */))
Frame 34: 13 bytes on wire (104 bits), 13 bytes captured (104 bits)
Bluetooth HCI H4
Bluetooth HCI ACL Packet
    .... 0000 0000 0010 = Connection Handle: 0x0002
    ..10 .... .... .... = PB Flag: First Automatically Flushable Packet (2)
    00.. .... .... .... = BC Flag: Point-To-Point (0)
    Data Total Length: 8
Bluetooth L2CAP Packet
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Add initial definitions for the new Bluetooth Management interface to
the bluetooth headers.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Remove extra spaces from legal text so that legal stuff looks
the same for all bluetooth code.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Do not use assignment in IF condition, remove extra spaces,
fixing typos, simplify code.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

HCI transport drivers may not know what type of radio an AMP device has
so only say whether they're BR/EDR or AMP devices.
Signed-off-by: NDavid Vrabel <david.vrabel@csr.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

To make net/ and include/net/ code consistent use __packed instead of
__attribute__ ((packed)). Bluetooth subsystem was one of the last net
subsys still using __attribute__ ((packed)).
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In some circumstances it could be desirable to reject incoming
connections on the baseband level. This patch adds this feature through
two new ioctl's: HCIBLOCKADDR and HCIUNBLOCKADDR. Both take a simple
Bluetooth address as a parameter. BDADDR_ANY can be used with
HCIUNBLOCKADDR to remove all devices from the blacklist.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

With the Bluetooth 3.0 specification and the introduction of alternate
MAC/PHY (AMP) support, it is required to differentiate between primary
BR/EDR controllers and 802.11 AMP controllers. So introduce a special
type inside HCI device for differentiation.

For now all AMP controllers will be treated as raw devices until an
AMP manager has been implemented.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The hdev->type is misnamed and should be actually hdev->bus instead. So
convert it now.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Bluetooth stack uses a reference counting for all established ACL
links and if no user (L2CAP connection) is present, the link will be
terminated to save power. The problem part is the dedicated pairing
when using Legacy Pairing (Bluetooth 2.0 and before). At that point
no user is present and pairing attempts will be disconnected within
10 seconds or less. In previous kernel version this was not a problem
since the disconnect timeout wasn't triggered on incoming connections
for the first time. However this caused issues with broken host stacks
that kept the connections around after dedicated pairing. When the
support for Simple Pairing got added, the link establishment procedure
needed to be changed and now causes issues when using Legacy Pairing

When using Simple Pairing it is possible to do a proper reference
counting of ACL link users. With Legacy Pairing this is not possible
since the specification is unclear in some areas and too many broken
Bluetooth devices have already been deployed. So instead of trying to
deal with all the broken devices, a special pairing timeout will be
introduced that increases the timeout to 60 seconds when pairing is
triggered.

If a broken devices now puts the stack into an unforeseen state, the
worst that happens is the disconnect timeout triggers after 120 seconds
instead of 4 seconds. This allows successful pairings with legacy and
broken devices now.

Based on a report by Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When attempting to setup eSCO connections it can happen that some link
manager implementations fail to properly negotiate the eSCO parameters
and thus fail the eSCO setup. Normally the link manager is responsible
for the negotiation of the parameters and actually fallback to SCO if
no agreement can be reached. In cases where the link manager is just too
stupid, then at least try to establish a SCO link if eSCO fails.

For the Bluetooth devices with EDR support this includes handling packet
types of EDR basebands. This is particular tricky since for the EDR the
logic of enabling/disabling one specific packet type is turned around.
This fix contains an extra bitmask to disable eSCO EDR packet when
trying to fallback to a SCO connection.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Bluetooth subsystem was not using the HCI Reset command when doing
device initialization. The Bluetooth 1.0b specification was ambiguous
on how the device firmware was suppose to handle it. Almost every device
was triggering a transport reset at the same time. In case of USB this
ended up in disconnects from the bus.

All modern Bluetooth dongles handle this perfectly fine and a lot of
them actually require that HCI Reset is sent. If not then they are
either stuck in their HID Proxy mode or their internal structures for
inquiry and paging are not correctly setup.

To handle old and new devices smoothly the Bluetooth subsystem contains
a quirk to force the HCI Reset on initialization. However maintaining
such a quirk becomes more and more complicated. This patch turns the
logic around and lets the old devices disable the HCI Reset command.

The only device where the HCI_QUIRK_NO_RESET is still needed are the
original Digianswer devices and dongles with an early CSR firmware.

CSR reported that they fixed this for version 12 firmware. The last
official release of version 11 firmware is build ID 115. The first
version 12 candidate was build ID 117.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

With the Simple Pairing support, the authentication requirements are
an explicit setting during the bonding process. Track and enforce the
requirements and allow higher layers like L2CAP and RFCOMM to increase
them if needed.

This patch introduces a new IOCTL that allows to query the current
authentication requirements. It is also possible to detect Simple
Pairing support in the kernel this way.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Bluetooth technology introduces new features on a regular basis
and for some of them it is important that the hardware on both sides
support them. For features like Simple Pairing it is important that
the host stacks on both sides have switched this feature on. To make
valid decisions, a config stage during ACL link establishment has been
introduced that retrieves remote features and if needed also the remote
extended features (known as remote host features) before signalling
this link as connected.

This change introduces full reference counting of incoming and outgoing
ACL links and the Bluetooth core will disconnect both if no owner of it
is present. To better handle interoperability during the pairing phase
the disconnect timeout for incoming connections has been increased to
10 seconds. This is five times more than for outgoing connections.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Simple Pairing process can only be used if both sides have the
support enabled in the host stack. The current Bluetooth specification
has three ways to detect this support.

If an Extended Inquiry Result has been sent during inquiry then it
is safe to assume that Simple Pairing is enabled. It is not allowed
to enable Extended Inquiry without Simple Pairing. During the remote
name request phase a notification with the remote host supported
features will be sent to indicate Simple Pairing support. Also the
second page of the remote extended features can indicate support for
Simple Pairing.

For all three cases the value of remote Simple Pairing mode is stored
in the inquiry cache for later use.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Simple Pairing feature is optional and needs to be enabled by the
host stack first. The Linux kernel relies on the Bluetooth daemon to
either enable or disable it, but at any time it needs to know the
current state of the Simple Pairing mode. So track any changes made
by external entities and store the current mode in the HCI device
structure.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

During the Simple Pairing process the HCI disconnect timer must be
disabled. The way to do this is by holding a reference count of the
HCI connection. The Simple Pairing process on both sides starts with
an IO Capabilities Request and ends with Simple Pairing Complete.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Bluetooth specification supports the default link policy settings
on a per host controller basis. For every new connection the link
manager would then use these settings. It is better to use this instead
of bothering the controller on every connection setup to overwrite the
default settings.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The connection packet type can be changed after the connection has been
established and thus needs to be properly tracked to ensure that the
host stack has always correct and valid information about it.

On incoming connections the Bluetooth core switches the supported packet
types to the configured list for this controller. However the usefulness
of this feature has been questioned a lot. The general consent is that
every Bluetooth host stack should enable as many packet types as the
hardware actually supports and leave the decision to the link manager
software running on the Bluetooth chip.

When running on Bluetooth 2.0 or later hardware, don't change the packet
type for incoming connections anymore. This hardware likely supports
Enhanced Data Rate and thus leave it completely up to the link manager
to pick the best packet type.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Bluetooth HCI commands are divided into logical OGF groups for
easier identification of their purposes. While this still makes sense
for the written specification, its makes the code only more complex
and harder to read. So instead of using separate OGF and OCF values
to identify the commands, use a common 16-bit opcode that combines
both values. As a side effect this also reduces the complexity of
OGF and OCF calculations during command header parsing.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To better support and handle eSCO links in the future a bunch of
constants needs to be added and some basic routines need to be
updated. This is the initial step.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

For consistency with other skb data accessors, reducing the number of direct
accesses to skb->data.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In case of non-blocking connects it is possible that the last user
of an ACL link quits before the connection has been fully established.
This will lead to a race condition where the internal state of a
connection is closed, but the actual link has been established and is
active. In case of Bluetooth 1.2 and later devices it is possible to
call create connection cancel to abort the connect. For older devices
the disconnect timer will be used to trigger the needed disconnect.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The command complete event of the exit periodic inquiry command must
clear the HCI_INQUIRY flag and finish the HCI request.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch assigns the next free HCI device identifier to Bluetooth
devices based on the SDIO interface.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>