The PHY library currently does not know about the the reverse MII
connection type. Add it to the list of supported PHY modes and update
of_get_phy_mode() to support it and look for the string "rev-mii".
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before this patch, ip_tunnel_xmit() was using the field protocol from the IP
header passed into argument.
There is no functional change, this patch prepares the support of IPv4 over
IPv4 for module sit.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 1a37e412 (net: Use 16bits for *_headers
fields of struct skbuff) converts skb->*_header to u16,
some #if NET_SKBUFF_DATA_USES_OFFSET are now useless,
and to be safe, we could just use "X = (typeof(X)) ~0U;"
as suggested by David.

Cc: David S. Miller <davem@davemloft.net>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for this new phy ID.
Signed-off-by: NRick Hoover <RHoover@digilentinc.com>
Signed-off-by: NSteven Wang <steven.wang@digilentinc.com>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This phy is on Xilinx ZC702 zynq development board.
Signed-off-by: NAnirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a struct device_node pointer for a phy passed by phandle
to mv643xx_eth node.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer however skb->network_header is now
an offset.

This patch corrects the problem by adding a wrapper to return skb tail as
an offset regardless of the value of NET_SKBUFF_DATA_USES_OFFSET. It seems
that skb->tail that this offset may be more than 64k and some care has been
taken to treat such cases as an error.
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer whereas skb->transport_header
will be an offset from head. This is corrected by using wrappers that
ensure that comparisons and calculations are always made using pointers.
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 351638e7 (net: pass info struct via netdevice notifier)
breaks booting of my KVM guest, this is due to we still forget to pass
struct netdev_notifier_info in several places. This patch completes it.

Cc: Jiri Pirko <jiri@resnulli.us>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use new netdevice notifier infrastructure to pass along changed flags.
Signed-off-by: NTimo Teräs <timo.teras@iki.fi>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>

v2->v3: shortened notifier_info struct name
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>

v2->v3: fix typo on simeth
	shortened dev_getter
	shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netpoll_rx_disable() will always return 0, it is no use and looks wordy,
so remove the unnecessary code and get rid of it in _dev_open and _dev_close.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the case where a non-MPLS packet is received and an MPLS stack is
added it may well be the case that the original skb is GSO but the
NIC used for transmit does not support GSO of MPLS packets.

The aim of this code is to provide GSO in software for MPLS packets
whose skbs are GSO.

SKB Usage:

When an implementation adds an MPLS stack to a non-MPLS packet it should do
the following to skb metadata:

* Set skb->inner_protocol to the old non-MPLS ethertype of the packet.
  skb->inner_protocol is added by this patch.

* Set skb->protocol to the new MPLS ethertype of the packet.

* Set skb->network_header to correspond to the
  end of the L3 header, including the MPLS label stack.

I have posted a patch, "[PATCH v3.29] datapath: Add basic MPLS support to
kernel" which adds MPLS support to the kernel datapath of Open vSwtich.
That patch sets the above requirements in datapath/actions.c:push_mpls()
and was used to exercise this code.  The datapath patch is against the Open
vSwtich tree but it is intended that it be added to the Open vSwtich code
present in the mainline Linux kernel at some point.

Features:

I believe that the approach that I have taken is at least partially
consistent with the handling of other protocols.  Jesse, I understand that
you have some ideas here.  I am more than happy to change my implementation.

This patch adds dev->mpls_features which may be used by devices
to advertise features supported for MPLS packets.

A new NETIF_F_MPLS_GSO feature is added for devices which support
hardware MPLS GSO offload.  Currently no devices support this
and MPLS GSO always falls back to software.

Alternate Implementation:

One possible alternate implementation is to teach netif_skb_features()
and skb_network_protocol() about MPLS, in a similar way to their
understanding of VLANs. I believe this would avoid the need
for net/mpls/mpls_gso.c and in particular the calls to
__skb_push() and __skb_push() in mpls_gso_segment().

I have decided on the implementation in this patch as it should
not introduce any overhead in the case where mpls_gso is not compiled
into the kernel or inserted as a module.

MPLS GSO suggested by Jesse Gross.
Based in part on "v4 GRE: Add TCP segmentation offload for GRE"
by Pravin B Shelar.

Cc: Jesse Gross <jesse@nicira.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to mitigate ongoing incresase in the size of struct skbuff
use 16 bit integer offsets rather than pointers for inner_*_headers.

This appears to reduce the size of struct skbuff from 0xd0 to 0xc0
bytes on x86_64 with the following all unset.

	CONFIG_XFRM
	CONFIG_NF_CONNTRACK
	CONFIG_NF_CONNTRACK_MODULE
	NET_SKBUFF_NF_DEFRAG_NEEDED
	CONFIG_BRIDGE_NETFILTER
	CONFIG_NET_SCHED
	CONFIG_IPV6_NDISC_NODETYPE
	CONFIG_NET_DMA
	CONFIG_NETWORK_SECMARK
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

libphy currently always reports a PHY as an external transceiver from
the ethtool output. This is inaccurate, because some drivers should be
able to tell that a PHY device is an internal transceiver of an Ethernet
MAC. Add a new flag (PHY_IS_INTERNAL) which can be set by PHY drivers
just like other flags, and a corresponding helper: phy_is_internal()
which can be used by networking drivers to query if a given
PHY device is internal.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a comment which explains the real meaning of XCVR_INTERNAL (PHY and
Ethernet MAC in the same package/die) and XCVR_EXTERNAL (PHY and
Ethernet MAC in a different package/die). Most if not all of the drivers
setting their transceiver type already do it the way the comment
describes it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now when upper device is changed, event is not propagated via RT Netlink
to userspace. Userspace might never now about the change. Fix this by
adding upper-device-change notifier event.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the ability to send ICMPv6 echo requests without a
raw socket. The equivalent ability for ICMPv4 was added in
2011.

Instead of having separate code paths for IPv4 and IPv6, make
most of the code in net/ipv4/ping.c dual-stack and only add a
few IPv6-specific bits (like the protocol definition) to a new
net/ipv6/ping.c. Hopefully this will reduce divergence and/or
duplication of bugs in the future.

Caveats:

- Setting options via ancillary data (e.g., using IPV6_PKTINFO
  to specify the outgoing interface) is not yet supported.
- There are no separate security settings for IPv4 and IPv6;
  everything is controlled by /proc/net/ipv4/ping_group_range.
- The proc interface does not yet display IPv6 ping sockets
  properly.

Tested with a patched copy of ping6 and using raw socket calls.
Compiles and works with all of CONFIG_IPV6={n,m,y}.
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch synchronises documentation for feature-split-event-channels from
Xen canonical header file.
Signed-off-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If <linux/linkage.h> has not been included before <linux/printk.h>,
a build error like the below one will result:

  CC      arch/mips/kernel/idle.o
In file included from arch/mips/kernel/idle.c:17:0:
include/linux/printk.h:109:1: error: data definition has no type or storage class [-Werror]
include/linux/printk.h:109:1: error: type defaults to ‘int’ in declaration of ‘asmlinkage’ [-Werror=implicit-int]
include/linux/printk.h:110:1: error: ‘format’ attribute only applies to function types [-Werror=attributes]
include/linux/printk.h:110:1: error: expected ‘,’ or ‘;’ before ‘int’
include/linux/printk.h:114:1: error: data definition has no type or storage class [-Werror]
include/linux/printk.h:114:1: error: type defaults to ‘int’ in declaration of ‘asmlinkage’ [-Werror=implicit-int]
include/linux/printk.h:115:1: error: ‘format’ attribute only applies to function types [-Werror=attributes]
include/linux/printk.h:115:1: error: expected ‘,’ or ‘;’ before ‘int’
include/linux/printk.h:117:1: error: data definition has no type or storage class [-Werror]
include/linux/printk.h:117:1: error: type defaults to ‘int’ in declaration of ‘asmlinkage’ [-Werror=implicit-int]
include/linux/printk.h:118:1: error: ‘format’ attribute only applies to function types [-Werror=attributes]
include/linux/printk.h:118:1: error: ‘__cold__’ attribute ignored [-Werror=attributes]
include/linux/printk.h:118:1: error: expected ‘,’ or ‘;’ before ‘asmlinkage’
include/linux/printk.h:122:1: error: data definition has no type or storage class [-Werror]
include/linux/printk.h:122:1: error: type defaults to ‘int’ in declaration of ‘asmlinkage’ [-Werror=implicit-int]
include/linux/printk.h:123:1: error: ‘format’ attribute only applies to function types [-Werror=attributes]
include/linux/printk.h:123:1: error: ‘__cold__’ attribute ignored [-Werror=attributes]
include/linux/printk.h:123:1: error: expected ‘,’ or ‘;’ before ‘int’
In file included from include/linux/kernel.h:14:0,
                 from include/linux/sched.h:15,
                 from arch/mips/kernel/idle.c:18:
include/linux/dynamic_debug.h: In function ‘ddebug_dyndbg_module_param_cb’:
include/linux/dynamic_debug.h:124:3: error: implicit declaration of function ‘printk’ [-Werror=implicit-function-declaration]

Fixed by including <linux/linkage.h>.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

There is currently no way for an Ethernet MAC driver servicing PHY link
interrupts to notify this to the PHY state machine without defining its
own state machine. Since most drivers are not so special, introduce a
helper: phy_mac_interrupt() which can be called from a link up/down
interrupt routine to update the PHY state machine. To avoid code
duplication some refactoring has been done to expose the workqueue and
its corresponding callback internally.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a PHY device is registered with the special IRQ value
PHY_IGNORE_INTERRUPT (-2) it will not properly be handled by the PHY
library:

- it continues to poll its register, while we do not want this
  because such PHY link events or register changes are serviced by an
  Ethernet MAC
- it will still try to configure PHY interrupts at the PHY level, such
  interrupts do not exist at the PHY but at the MAC level
- the state machine only handles PHY_POLL, but should also handle
  PHY_IGNORE_INTERRUPT similarly

This patch updates the PHY state machine and initialization paths to
account for the specific PHY_IGNORE_INTERRUPT. Based on an earlier patch
by Thomas Petazzoni, and reworked to add the missing bits. Add a helper
phy_interrupt_is_valid() which specifically tests for a PHY interrupt
not to be PHY_POLL or PHY_IGNORE_INTERRUPT and use it throughout the
code.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCP md5 code uses per cpu variables but protects access to them with
a shared spinlock, which is a contention point.

[ tcp_md5sig_pool_lock is locked twice per incoming packet ]

Makes things much simpler, by allocating crypto structures once, first
time a socket needs md5 keys, and not deallocating them as they are
really small.

Next step would be to allow crypto allocations being done in a NUMA
aware way.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The next pointer within the inet6_dev structure seems not to be used
anywhere. So just remove it. Tested with allmodconfig on x86_64.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A cpu executing the network receive path sheds packets when its input
queue grows to netdev_max_backlog. A single high rate flow (such as a
spoofed source DoS) can exceed a single cpu processing rate and will
degrade throughput of other flows hashed onto the same cpu.

This patch adds a more fine grained hashtable. If the netdev backlog
is above a threshold, IRQ cpus track the ratio of total traffic of
each flow (using 4096 buckets, configurable). The ratio is measured
by counting the number of packets per flow over the last 256 packets
from the source cpu. Any flow that occupies a large fraction of this
(set at 50%) will see packet drop while above the threshold.

Tested:
Setup is a muli-threaded UDP echo server with network rx IRQ on cpu0,
kernel receive (RPS) on cpu0 and application threads on cpus 2--7
each handling 20k req/s. Throughput halves when hit with a 400 kpps
antagonist storm. With this patch applied, antagonist overload is
dropped and the server processes its complete load.

The patch is effective when kernel receive processing is the
bottleneck. The above RPS scenario is a extreme, but the same is
reached with RFS and sufficient kernel processing (iptables, packet
socket tap, ..).
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the tty port owns the flip buffers and i/o is allowed
from the driver even when no tty is attached, the destruction
of the tty port (and the flip buffers) must ensure that no
outstanding work is pending.

Unfortunately, this creates a lock order problem with the
console_lock (see attached lockdep report [1] below).

For single console deallocation, drop the console_lock prior
to port destruction. When multiple console deallocation,
defer port destruction until the consoles have been
deallocated.

tty_port_destroy() is not required if the port has not
been used; remove from vc_allocate() failure path.

[1] lockdep report from Dave Jones <davej@redhat.com>

 ======================================================
 [ INFO: possible circular locking dependency detected ]
 3.9.0+ #16 Not tainted
 -------------------------------------------------------
 (agetty)/26163 is trying to acquire lock:
 blocked:  ((&buf->work)){+.+...}, instance: ffff88011c8b0020, at: [<ffffffff81062065>] flush_work+0x5/0x2e0

 but task is already holding lock:
 blocked:  (console_lock){+.+.+.}, instance: ffffffff81c2fde0, at: [<ffffffff813bc201>] vt_ioctl+0xb61/0x1230

 which lock already depends on the new lock.

 the existing dependency chain (in reverse order) is:

 -> #1 (console_lock){+.+.+.}:
        [<ffffffff810b3f74>] lock_acquire+0xa4/0x210
        [<ffffffff810416c7>] console_lock+0x77/0x80
        [<ffffffff813c3dcd>] con_flush_chars+0x2d/0x50
        [<ffffffff813b32b2>] n_tty_receive_buf+0x122/0x14d0
        [<ffffffff813b7709>] flush_to_ldisc+0x119/0x170
        [<ffffffff81064381>] process_one_work+0x211/0x700
        [<ffffffff8106498b>] worker_thread+0x11b/0x3a0
        [<ffffffff8106ce5d>] kthread+0xed/0x100
        [<ffffffff81601cac>] ret_from_fork+0x7c/0xb0

 -> #0 ((&buf->work)){+.+...}:
        [<ffffffff810b349a>] __lock_acquire+0x193a/0x1c00
        [<ffffffff810b3f74>] lock_acquire+0xa4/0x210
        [<ffffffff810620ae>] flush_work+0x4e/0x2e0
        [<ffffffff81065305>] __cancel_work_timer+0x95/0x130
        [<ffffffff810653b0>] cancel_work_sync+0x10/0x20
        [<ffffffff813b8212>] tty_port_destroy+0x12/0x20
        [<ffffffff813c65e8>] vc_deallocate+0xf8/0x110
        [<ffffffff813bc20c>] vt_ioctl+0xb6c/0x1230
        [<ffffffff813b01a5>] tty_ioctl+0x285/0xd50
        [<ffffffff811ba825>] do_vfs_ioctl+0x305/0x530
        [<ffffffff811baad1>] sys_ioctl+0x81/0xa0
        [<ffffffff81601d59>] system_call_fastpath+0x16/0x1b

 other info that might help us debug this:

 [ 6760.076175]  Possible unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(console_lock);
                                lock((&buf->work));
                                lock(console_lock);
   lock((&buf->work));

  *** DEADLOCK ***

 1 lock on stack by (agetty)/26163:
  #0: blocked:  (console_lock){+.+.+.}, instance: ffffffff81c2fde0, at: [<ffffffff813bc201>] vt_ioctl+0xb61/0x1230
 stack backtrace:
 Pid: 26163, comm: (agetty) Not tainted 3.9.0+ #16
 Call Trace:
  [<ffffffff815edb14>] print_circular_bug+0x200/0x20e
  [<ffffffff810b349a>] __lock_acquire+0x193a/0x1c00
  [<ffffffff8100a269>] ? sched_clock+0x9/0x10
  [<ffffffff8100a269>] ? sched_clock+0x9/0x10
  [<ffffffff8100a200>] ? native_sched_clock+0x20/0x80
  [<ffffffff810b3f74>] lock_acquire+0xa4/0x210
  [<ffffffff81062065>] ? flush_work+0x5/0x2e0
  [<ffffffff810620ae>] flush_work+0x4e/0x2e0
  [<ffffffff81062065>] ? flush_work+0x5/0x2e0
  [<ffffffff810b15db>] ? mark_held_locks+0xbb/0x140
  [<ffffffff8113c8a3>] ? __free_pages_ok.part.57+0x93/0xc0
  [<ffffffff810b15db>] ? mark_held_locks+0xbb/0x140
  [<ffffffff810652f2>] ? __cancel_work_timer+0x82/0x130
  [<ffffffff81065305>] __cancel_work_timer+0x95/0x130
  [<ffffffff810653b0>] cancel_work_sync+0x10/0x20
  [<ffffffff813b8212>] tty_port_destroy+0x12/0x20
  [<ffffffff813c65e8>] vc_deallocate+0xf8/0x110
  [<ffffffff813bc20c>] vt_ioctl+0xb6c/0x1230
  [<ffffffff810aec41>] ? lock_release_holdtime.part.30+0xa1/0x170
  [<ffffffff813b01a5>] tty_ioctl+0x285/0xd50
  [<ffffffff812b00f6>] ? inode_has_perm.isra.46.constprop.61+0x56/0x80
  [<ffffffff811ba825>] do_vfs_ioctl+0x305/0x530
  [<ffffffff812b04db>] ? selinux_file_ioctl+0x5b/0x110
  [<ffffffff811baad1>] sys_ioctl+0x81/0xa0
  [<ffffffff81601d59>] system_call_fastpath+0x16/0x1b

Cc: Dave Jones <davej@redhat.com>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>

Do not leak starting address of BPF JIT code for non root users,
as it might help intruders to perform an attack.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_timeout_skb() was intended to trigger fast recovery on timeout,
unfortunately in reality it often causes spurious retransmission
storms during fast recovery. The particular sign is a fast retransmit
over the highest sacked sequence (SND.FACK).

Currently the RTO timer re-arming (as in RFC6298) offers a nice cushion
to avoid spurious timeout: when SND.UNA advances the sender re-arms
RTO and extends the timeout by icsk_rto. The sender does not offset
the time elapsed since the packet at SND.UNA was sent.

But if the next (DUP)ACK arrives later than ~RTTVAR and triggers
tcp_fastretrans_alert(), then tcp_timeout_skb() will mark any packet
sent before the icsk_rto interval lost, including one that's above the
highest sacked sequence. Most likely a large part of scorebard will be
marked.

If most packets are not lost then the subsequent DUPACKs with new SACK
blocks will cause the sender to continue to retransmit packets beyond
SND.FACK spuriously. Even if only one packet is lost the sender may
falsely retransmit almost the entire window.

The situation becomes common in the world of bufferbloat: the RTT
continues to grow as the queue builds up but RTTVAR remains small and
close to the minimum 200ms. If a data packet is lost and the DUPACK
triggered by the next data packet is slightly delayed, then a spurious
retransmission storm forms.

As the original comment on tcp_timeout_skb() suggests: the usefulness
of this feature is questionable. It also wastes cycles walking the
sack scoreboard and is actually harmful because of false recovery.

It's time to remove this.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NNandita Dukkipati <nanditad@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

uapi should use __u32 not u32.
Fix a macro in virtio_console.h which uses u32.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org

ERROR: "memcpy_fromiovec" [drivers/vhost/vhost_scsi.ko] undefined!

That function is only present with CONFIG_NET.  Turns out that
crypto/algif_skcipher.c also uses that outside net, but it actually
needs sockets anyway.

In addition, commit 6d4f0139 added
CONFIG_NET dependency to CONFIG_VMCI for memcpy_toiovec, so hoist
that function and revert that commit too.

socket.h already includes uio.h, so no callers need updating; trying
only broke things fo x86_64 randconfig (thanks Fengguang!).
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

This patch adds the support of peer address for IPv6. For example, it is
possible to specify the remote end of a 6inY tunnel.
This was already possible in IPv4:
 ip addr add ip1 peer ip2 dev dev1

The peer address is specified with IFA_ADDRESS and the local address with
IFA_LOCAL (like explained in include/uapi/linux/if_addr.h).
Note that the API is not changed, because before this patch, it was not
possible to specify two different addresses in IFA_LOCAL and IFA_REMOTE.
There is a small change for the dump: if the peer is different from ::,
IFA_ADDRESS will contain the peer address instead of the local address.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a PCI host bridge device receives a Bus Check notification, we
must re-enumerate starting with the bridge to discover changes (devices
that have been added or removed).

Prior to 668192b6 ("PCI: acpiphp: Move host bridge hotplug to
pci_root.c"), this happened in _handle_hotplug_event_bridge().  After that
commit, _handle_hotplug_event_bridge() is not installed for host bridges,
and the host bridge notify handler, _handle_hotplug_event_root() did not
re-enumerate.

This patch adds re-enumeration to _handle_hotplug_event_root().

This fixes cases where we don't notice the addition or removal of
PCI devices, e.g., the PCI-to-USB ExpressCard in the bugzilla below.

[bhelgaas: changelog, references]
Reference: https://lkml.kernel.org/r/CAAh6nkmbKR3HTqm5ommevsBwhL_u0N8Rk7Wsms_LfP=nBgKNew@mail.gmail.com
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=57961Reported-by: NGavin Guo <tuffkidtt@gmail.com>
Tested-by: NGavin Guo <tuffkidtt@gmail.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NJiang Liu <jiang.liu@huawei.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org	# v3.9+

PCIe and ARM CR4 cores were found on 14e4:43b1 AKA BCM4352.
Reported-by: NGabriel Thörnblad <gabriel@thornblad.com>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add generic wait_until_sent implementation which polls for empty
hardware buffers using the new port-operation tx_empty.

The generic implementation will be used for all sub-drivers that
implement tx_empty but does not define wait_until_sent.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add wait_until_sent operation which can be used to wait for hardware
buffers to drain.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

AB8500 sysctrl driver implements a pm_power_off handler, but that is
currently not registered until a specific platform data field is
enabled.

This patch drops the platform data field and always registers
ab8500_power_off if no other pm_power_off handler was defined before,
and also introduces the necessary cleanup code in the driver's remove
function.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

In some situations, we need to disable TSO on bonding slaves.

bonding device automatically unset TSO in bond_fix_features(), and
performance is not good because :

1) We consume more cpu cycles.

2) GSO segmentation has some bugs leading to out of order TCP packets
if this segmentation is done before virtual device. This particular
problem will be addressed in a separate patch.

This patch allows TSO being set/unset on the bonding master,
so that GSO segmentation is done after bonding layer.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Michał Mirosław <mirqus@gmail.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Document rx vs tx status concurrency requirements.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

include/linux/brcmphy.h is currently not protected against double
inclusion, add ifdefs guard to fix that.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>