In preparation for Dynamic PCM support (AKA DSP support).

There will be future patches that add support to allow PCMs to be dynamically
routed to multiple DAIs at startup and also during stream runtime. This patch
moves the ASoC core PCM operaitions into a new file called soc-pcm.c.  This will
in simplify the ASoC core features into distinct files.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some ASoC components depend on other ASoC components to provide clocks and
power resources in order to probe() and vice versa for remove().

Allow components to be ordered so that components can be probed() and removed()
in sequences that conform to their dependencies.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Currently pcm_new() passes in 3 arguments :- card, pcm and DAI.

Refactor this to only pass in 1 argument (i.e. the rtd) since struct rtd contains
card, pcm and DAI along with other members too that are useful too.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Avoids issues if someone does a read followed by restore and doesn't mask
out only the bits being updated.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

For cards that have two or more DAIs, snd_soc_resume's loop over all
DAIs ends up calling schedule_work(deferred_resume_work) once per DAI.
Since this is the same work item each time, the 2nd and subsequent
calls return 0 (work item already queued), and trigger the dev_err
message below stating that a work item may have been lost.

Solve this by adjusting the loop to simply calculate whether to run the
resume work immediately or defer it, and then call schedule work (or not)
one time based on that.

Note: This has not been tested in mainline, but only in chromeos-2.6.38;
mainline doesn't support suspend/resume on Tegra, nor does the mainline
Tegra ASoC driver contain multiple DAIs. It has been compile-checked in
mainline.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Currently CODEC and platform drivers have their module reference count
incremented soc_probe_dai_link() whilst CPU DAI drivers have their reference
count incremented in soc_bind_dai_link().

CPU DAIs should have their reference count incremented in soc_probe_dai_link()
just like the CODEC and platform drivers.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Commit 22de71ba ("ASoC: core - allow ASoC more flexible machine name")
writes "(null)" to driver name string in struct snd_card if card->driver_name
is NULL. This causes segmentation faults with some user space ALSA utilities
like aplay and arecord.

Fix this by using the card->name if no driver name is specified.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Enabling DEBUG_STRICT_USER_COPY_CHECKS causes the following
warning:

In file included from arch/x86/include/asm/uaccess.h:573,
                 from include/linux/poll.h:14,
                 from include/sound/pcm.h:29,
                 from include/sound/ac97_codec.h:31,
                 from sound/soc/soc-core.c:34:
In function 'copy_from_user',
    inlined from 'codec_reg_write_file' at
    sound/soc/soc-core.c:252:
arch/x86/include/asm/uaccess_64.h:65:
warning: call to 'copy_from_user_overflow' declared with
attribute warning: copy_from_user() buffer size is not provably
correct

presumably due to buf_size being signed causing GCC to fail to
see that buf_size can't become negative.
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allow ASoC machine drivers to register a driver name
and a longname. This allows user space to determine
the flavour of machine driver.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This allows to create DAPM routes depending on those widgets in the
codecs probe function.  This is helpful when supporting similar codecs
with minor differences in the DAPM routing with the same driver.

Something similar has already been done for cards in commit
a841ebb9 (ASoC: Create card DAPM widgets early so they can be used in
callbacks).
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The move over to exposing snd_soc_register_card() let the initialisation
of the driver data we use to find the card in PM operations go AWOL. Fix
this by setting the driver data when we register the card.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Currently debugfs entries for a DAPM widgets are only added in
snd_soc_dapm_debugfs_init. If a widget is added later (for example in the
dai_link's probe callback) it will not show up in debugfs.
This patch moves the creation of the widget debugfs entry to
snd_soc_dapm_new_widgets where it will be added after the widget has been
properly instantiated.

As a side-effect this will also reduce the number of times the DAPM widget list
is iterated during a card's instantiation.

Since it is possible that snd_soc_dapm_new_widgets is invoked form the codecs or
cards probe callbacks, the creation of the debugfs dapm directory has to be
moved before these are called.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Move the creation of the DAPM debugfs directory to snd_soc_dapm_debugfs_init
instead of having the same duplicated code in both codec and card DAPM setup.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Free the card's DAPM context when the card is removed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Since we can now support multiple platforms allow machines to not specify
a platform in a DAI link. Since the rest of the code requires that we have
a struct device for all objects we do this by substituting in a dummy
device that we register automatically.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJassi Brar <jassisinghbrar@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJassi Brar <jassisinghbrar@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Signed-off-by: NLu Guanqun <guanqun.lu@intel.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This helps with things like setting up the initial state.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

card->num_rtd should be 0 after soc_romve_dai_link
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allow CODEC and card drivers to point to an array of controls from their
driver structure rather than explicitly calling snd_soc_add_controls().
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

initialize ret to invalid value so that when we reach the config error path in
soc_pcm_open, it will return the correct error code. without this patch, though
config error path is executed, soc_pcm_open will return 0 in
snd_pcm_open_substream and then cause double release of substream.
Signed-off-by: NLu Guanqun <guanqun.lu@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Suppose we have:

	cpu_dai
		channels_min = 1
		channels_max = 1

	codec_dai
		channels_min = 2
		channels_max = 2

This is a mismatch that should not happen, however according to the current
code, the result of runtime->hw will be:

		channels_min = 2
		channels_max = 1

We better spot it early. This patch checks this mismatch.
Signed-off-by: NLu Guanqun <guanqun.lu@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

ASoC machine drivers that are their own platform_driver (as opposed to
those using the soc-audio platform_driver) need to explicitly set up
power-management operation callbacks.

To avoid cut/paste, snd_soc_pm_ops also needs to be exported.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

wordsize is used as the textual width of a register address.

regsize is used as the textual width of a register value.

The assignments to these values were swapped. In the case of WM8903, which
has 8-bit register addresses and 16-bit register values, this caused the
register values to be clipped to 2 digits instead of the full 4.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Provide the top level ASoC core functions for indicating whether
a given register is readable or writable.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

By using struct snd_soc_reg_access for the read/write/vol attributes
of the registers, we provide callbacks that automatically determine whether
a given register is readable/writable or volatile.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

As it has become more common to have to write firmware or similar
large chunks of data to the hardware, add a function to perform
raw bulk writes that bypass the cache.  This only handles volatile
registers as we should avoid getting out of sync with the actual
cache.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since not all registers need to be cached and the cache is entirely
optional anyway we shouldn't be checking that a register is in the
cached range. If the register is invalid then the actual I/O code
can determine that and report an error.

Similarly, the step size can and should be enforced by the lower level
code if it's important.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Currently will ignore prefixes when creating DAPM controls. Since currently
all control creation goes through snd_soc_cnew() we can fix this by factoring
the prefixing into that function.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Symmetric rate configuration can fail if the second stream starting tries
to apply the symmetric constraint before the first stream has got far
enough to pick a rate. Rather than try to enforce a nonsensical rate of
0Hz log a warning and allow the application to carry on. Things might go
wrong later on but the user will know about it and there's unlikely to be
lasting damage.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

When multi component systems use DAIless amplifiers which require clocking
configuration it is at best hard to use the current clocking API as this
requires a DAI even though the device may not even have one. Address this
by adding set_sysclk() and set_pll() operations and APIs for CODECs.

In order to avoid issues with devices which could be used either with or
without DAIs make the DAI variants call through to their CODEC counterparts
if there is no DAI specific operation. Converting over entirely would create
problems for multi-DAI devices which offer per-DAI clocking setup.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Allow a slight simplification of CODEC drivers by allowing DAPM routes and
widgets to be provided in a table. They will be instantiated at the end of
CODEC probe.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This is run after the DAPM widgets and routes are added, allowing setup
of things like jacks using the routes. The main card probe() is run before
anything else so can't be used for this purpose.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

These will be added after all devices are registered and allow most DAI
init functions in machine drivers to be replaced by simple data.
Regular controls are not supported as the registration function still
works in terms of CODECs.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This means that rather than adding the board specific DAPM widgets to a
random CODEC DAPM context they can be added to the card itself which is
a bit cleaner. Previously there only was one DAPM context and it was
tied to the single supported CODEC.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The .card member of the snd_soc_pcm_runtime structure pointed to by the
snd_soc_dai_link.init() argument used to be initialized before the
function being called. This has changed, probably unintentionally,
after recent refactorings. Since the function implementations are free
to make use of this pointer, move its assignment back before the
function is called to avoid NULL pointer dereferences.

Created and tested on Amstrad Delta againts linux-2.6.38-rc2
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>