It's a debug option that you would explicitly enable to test this
feature, we should default it to 'n' to prevent accidental surprises
for now.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Extended devt introduces non-contiguos device numbers.  This patch
implements a debug option which forces most devt allocations to be
from the extended area and spreads them out.  This is enabled by
default if DEBUG_KERNEL is set and achieves...

1. Detects code paths in kernel or userland which expect predetermined
   consecutive device numbers.

2. When something goes wrong, avoid corruption as adding to the minor
   of earlier partition won't lead to the wrong but valid device.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This bug is causing random crashes
(http://bugzilla.kernel.org/show_bug.cgi?id=11414).

-fno-omit-frame-pointer is only needed on powerpc when -pg is also
supplied, and there is a gcc bug that causes incorrect code generation
on 32-bit powerpc when -fno-omit-frame-pointer is used---it uses stack
locations below the stack pointer, which is not allowed by the ABI
because those locations can and sometimes do get corrupted by an
interrupt.

This ensures that CONFIG_FRAME_POINTER is only selected by ftrace.
When CONFIG_FTRACE is enabled we also pass -mno-sched-epilog to work
around the gcc codegen bug.

Patch based on work by:
	Andreas Schwab <schwab@suse.de>
	Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

I noticed that sysctl_check.o was the largest object file in
a allnoconfig build in kernel/*.

  36243       0       0   36243    8d93 kernel/sysctl_check.o

This is because it was default y and && EMBEDDED. But I don't
really see a need for a non kernel developer to have their
sysctls checked all the time.

So move the Kconfig into the kernel debugging section and
also drop the default y and the EMBEDDED check.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently source files in the Documentation/ sub-dir can easily bit-rot
since they are not generally buildable, either because they are hidden in
text files or because there are no Makefile rules for them.  This needs to
be fixed so that the source files remain usable and good examples of code
instead of bad examples.

Add the ability to build source files that are in the Documentation/ dir.
Add to Kconfig as "BUILD_DOCSRC" config symbol.

Use "CONFIG_BUILD_DOCSRC=1 make ..." to build objects from the
Documentation/ sources.  Or enable BUILD_DOCSRC in the *config system.
However, this symbol depends on HEADERS_CHECK since the header files need
to be installed (for userspace builds).

Built (using cross-tools) for x86-64, i386, alpha, ia64, sparc32,
sparc64, powerpc, sh, m68k, & mips.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Reviewed-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Boot initialisation is very complex, with significant numbers of
architecture-specific routines, hooks and code ordering.  While significant
amounts of the initialisation is architecture-independent, it trusts the data
received from the architecture layer.  This is a mistake, and has resulted in
a number of difficult-to-diagnose bugs.

This patchset adds some validation and tracing to memory initialisation.  It
also introduces a few basic defensive measures.  The validation code can be
explicitly disabled for embedded systems.

This patch:

Add additional debugging and verification code for memory initialisation.

Once enabled, the verification checks are always run and when required
additional debugging information may be outputted via a mminit_loglevel=
command-line parameter.

The verification code is placed in a new file mm/mm_init.c.  Ideally other mm
initialisation code will be moved here over time.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Cc: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds saved stack-traces to the backtrace suite of self-tests.

Note that we don't depend on or unconditionally enable CONFIG_STACKTRACE
because not all architectures may have it (and we still want to enable the
other tests for those architectures).

Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: NVegard Nossum <vegard.nossum@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This patch re-institutes the ability to build rcutorture directly into
the Linux kernel.  The reason that this capability was removed was that
this could result in your kernel being pretty much useless, as rcutorture
would be running starting from early boot.  This problem has been avoided
by (1) making rcutorture run only three seconds of every six by default,
(2) adding a CONFIG_RCU_TORTURE_TEST_RUNNABLE that permits rcutorture
to be quiesced at boot time, and (3) adding a sysctl in /proc named
/proc/sys/kernel/rcutorture_runnable that permits rcutorture to be
quiesced and unquiesced when built into the kernel.

Please note that this /proc file is -not- available when rcutorture
is built as a module.  Please also note that to get the earlier
take-no-prisoners behavior, you must use the boot command line to set
rcutorture's "stutter" parameter to zero.

The rcutorture quiescing mechanism is currently quite crude: loops
in each rcutorture process that poll a global variable once per tick.
Suggestions for improvement are welcome.  The default action will
be to reduce the polling rate to a few times per second.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Suggested-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This reverts commit 9aaffc89.

That commit was a very bad idea. RCU_TORTURE found many boot timing
bugs and other sorts of bugs in the past, so excluding it from
boot images is very silly.

The option already depends on DEBUG_KERNEL and is disabled by default.
Even when it runs, the test threads are reniced. If it annoys people
we could add a runtime sysctl.

Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

allow users to configure the softlockup detector to generate a panic
instead of a warning message.

high-availability systems might opt for this strict method (combined
with panic_timeout= boot option/sysctl), instead of generating
softlockup warnings ad infinitum.

also, automated tests work better if the system reboots reliably (into
a safe kernel) in case of a lockup.

The full spectrum of configurability is supported: boot option, sysctl
option and Kconfig option.

it's default-disabled.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

If CONFIG_FTRACE is selected and /proc/sys/kernel/ftrace_enabled is
set to a non-zero value the ftrace routine will be called everytime
we enter a kernel function that is not marked with the "notrace"
attribute.

The ftrace routine will then call a registered function if a function
happens to be registered.

[ This code has been highly hacked by Steven Rostedt and Ingo Molnar,
  so don't blame Arnaldo for all of this ;-) ]

Update:
  It is now possible to register more than one ftrace function.
  If only one ftrace function is registered, that will be the
  function that ftrace calls directly. If more than one function
  is registered, then ftrace will call a function that will loop
  through the functions to call.
Signed-off-by: NArnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Add calls to the generic object debugging infrastructure and provide fixup
functions which allow to keep the system alive when recoverable problems have
been detected by the object debugging core code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We can see an ever repeating problem pattern with objects of any kind in the
kernel:

1) freeing of active objects
2) reinitialization of active objects

Both problems can be hard to debug because the crash happens at a point where
we have no chance to decode the root cause anymore.  One problem spot are
kernel timers, where the detection of the problem often happens in interrupt
context and usually causes the machine to panic.

While working on a timer related bug report I had to hack specialized code
into the timer subsystem to get a reasonable hint for the root cause.  This
debug hack was fine for temporary use, but far from a mergeable solution due
to the intrusiveness into the timer code.

The code further lacked the ability to detect and report the root cause
instantly and keep the system operational.

Keeping the system operational is important to get hold of the debug
information without special debugging aids like serial consoles and special
knowledge of the bug reporter.

The problems described above are not restricted to timers, but timers tend to
expose it usually in a full system crash.  Other objects are less explosive,
but the symptoms caused by such mistakes can be even harder to debug.

Instead of creating specialized debugging code for the timer subsystem a
generic infrastructure is created which allows developers to verify their code
and provides an easy to enable debug facility for users in case of trouble.

The debugobjects core code keeps track of operations on static and dynamic
objects by inserting them into a hashed list and sanity checking them on
object operations and provides additional checks whenever kernel memory is
freed.

The tracked object operations are:
- initializing an object
- adding an object to a subsystem list
- deleting an object from a subsystem list

Each operation is sanity checked before the operation is executed and the
subsystem specific code can provide a fixup function which allows to prevent
the damage of the operation.  When the sanity check triggers a warning message
and a stack trace is printed.

The list of operations can be extended if the need arises.  For now it's
limited to the requirements of the first user (timers).

The core code enqueues the objects into hash buckets.  The hash index is
generated from the address of the object to simplify the lookup for the check
on kfree/vfree.  Each bucket has it's own spinlock to avoid contention on a
global lock.

The debug code can be compiled in without being active.  The runtime overhead
is minimal and could be optimized by asm alternatives.  A kernel command line
option enables the debugging code.

Thanks to Ingo Molnar for review, suggestions and cleanup patches.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add option to enable -Wframe-larger-than= on gcc 4.4

gcc mainline (upcoming 4.4) added a new -Wframe-larger-than=...
option to warn at build time about too large stack frames. Add a config
option to enable this warning, since this very useful for the kernel.

I choose (somewhat arbitarily) 2048 as default warning threshold for 64bit
and 1024 as default for 32bit architectures.  With some research and
fixing all the code for smaller values these defaults should be probably
lowered.

With the default allyesconfigs have some new warnings, but I think
that is all code that should be just fixed.

At some point (when gcc 4.4 is released and widely used) this should
obsolete make checkstack
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

There have been a few oopses caused by 'struct file's with NULL f_vfsmnts.
There was also a set of potentially missed mnt_want_write()s from
dentry_open() calls.

This patch provides a very simple debugging framework to catch these kinds of
bugs.  It will WARN_ON() them, but should stop us from having any oopses or
mnt_writer count imbalances.

I'm quite convinced that this is a good thing because it found bugs in the
stuff I was working on as soon as I wrote it.

[hch: made it conditional on a debug option.
      But it's still a little bit too ugly]

[hch: merged forced remount r/o fix from Dave and akpm's fix for the fix]
Signed-off-by: NDave Hansen <haveblue@us.ibm.com>
Acked-by: NAl Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

This way firewire-ohci can be used for remote debugging like ohci1394.
Version with amendment from Fri, 11 Apr 2008 00:08:08 +0200.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NBernhard Kaindl <bk@suse.de>

kgdb core code. Handles the protocol and the arch details.

[ mingo@elte.hu: heavily modified, simplified and cleaned up. ]
[ xemul@openvz.org: use find_task_by_pid_ns ]
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>

Alpha and FRV mutexes had an option to print lots of debugging messages
in their semaphore implementation.  This feature has not been carried
over to the generic semaphores, so remove the stale Kconfig option.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

count_partial() is used by both slabinfo and the sysfs proc support. Move
the function directly before the beginning of the sysfs code so that it can
be easily found. Rework the preprocessor conditional to take into account
that slub sysfs support depends on CONFIG_SYSFS *and* CONFIG_SLUB_DEBUG.

Make CONFIG_SLUB_STATS depend on CONFIG_SLUB_DEBUG and CONFIG_SYSFS. There
is no point of keeping statistics if no one can restrive them.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>

Make LKDTM depend on BLOCK to prevent build failures with certain configs.
Signed-off-by: NChris Snook <csnook@redhat.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We started to see patches enabling this - so explain why
it is disabled and the condition to enable it again.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Other than the defconfigs, remove the entry in compiler-gcc4.h,
Kconfig.debug and feature-removal-schedule.txt.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Add architecture support for the MN10300/AM33 CPUs produced by MEI to the
kernel.

This patch also adds board support for the ASB2303 with the ASB2308 daughter
board, and the ASB2305.  The only processor supported is the MN103E010, which
is an AM33v2 core plus on-chip devices.

[akpm@linux-foundation.org: nuke cvs control strings]
Signed-off-by: NMasakazu Urade <urade.masakazu@jp.panasonic.com>
Signed-off-by: NKoichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The statistics provided here allow the monitoring of allocator behavior but
at the cost of some (minimal) loss of performance. Counters are placed in
SLUB's per cpu data structure. The per cpu structure may be extended by the
statistics to grow larger than one cacheline which will increase the cache
footprint of SLUB.

There is a compile option to enable/disable the inclusion of the runtime
statistics and its off by default.

The slabinfo tool is enhanced to support these statistics via two options:

-D 	Switches the line of information displayed for a slab from size
	mode to activity mode.

-A	Sorts the slabs displayed by activity. This allows the display of
	the slabs most important to the performance of a certain load.

-r	Report option will report detailed statistics on

Example (tbench load):

slabinfo -AD		->Shows the most active slabs

Name                   Objects    Alloc     Free   %Fast
skbuff_fclone_cache         33 111953835 111953835  99  99
:0000192                  2666  5283688  5281047  99  99
:0001024                   849  5247230  5246389  83  83
vm_area_struct            1349   119642   118355  91  22
:0004096                    15    66753    66751  98  98
:0000064                  2067    25297    23383  98  78
dentry                   10259    28635    18464  91  45
:0000080                 11004    18950     8089  98  98
:0000096                  1703    12358    10784  99  98
:0000128                   762    10582     9875  94  18
:0000512                   184     9807     9647  95  81
:0002048                   479     9669     9195  83  65
anon_vma                   777     9461     9002  99  71
kmalloc-8                 6492     9981     5624  99  97
:0000768                   258     7174     6931  58  15

So the skbuff_fclone_cache is of highest importance for the tbench load.
Pretty high load on the 192 sized slab. Look for the aliases

slabinfo -a | grep 000192
:0000192     <- xfs_btree_cur filp kmalloc-192 uid_cache tw_sock_TCP
	request_sock_TCPv6 tw_sock_TCPv6 skbuff_head_cache xfs_ili

Likely skbuff_head_cache.


Looking into the statistics of the skbuff_fclone_cache is possible through

slabinfo skbuff_fclone_cache	->-r option implied if cache name is mentioned


.... Usual output ...

Slab Perf Counter       Alloc     Free %Al %Fr
--------------------------------------------------
Fastpath             111953360 111946981  99  99
Slowpath                 1044     7423   0   0
Page Alloc                272      264   0   0
Add partial                25      325   0   0
Remove partial             86      264   0   0
RemoteObj/SlabFrozen      350     4832   0   0
Total                111954404 111954404

Flushes       49 Refill        0
Deactivate Full=325(92%) Empty=0(0%) ToHead=24(6%) ToTail=1(0%)

Looks good because the fastpath is overwhelmingly taken.


skbuff_head_cache:

Slab Perf Counter       Alloc     Free %Al %Fr
--------------------------------------------------
Fastpath              5297262  5259882  99  99
Slowpath                 4477    39586   0   0
Page Alloc                937      824   0   0
Add partial                 0     2515   0   0
Remove partial           1691      824   0   0
RemoteObj/SlabFrozen     2621     9684   0   0
Total                 5301739  5299468

Deactivate Full=2620(100%) Empty=0(0%) ToHead=0(0%) ToTail=0(0%)


Descriptions of the output:

Total:		The total number of allocation and frees that occurred for a
		slab

Fastpath:	The number of allocations/frees that used the fastpath.

Slowpath:	Other allocations

Page Alloc:	Number of calls to the page allocator as a result of slowpath
		processing

Add Partial:	Number of slabs added to the partial list through free or
		alloc (occurs during cpuslab flushes)

Remove Partial:	Number of slabs removed from the partial list as a result of
		allocations retrieving a partial slab or by a free freeing
		the last object of a slab.

RemoteObj/Froz:	How many times were remotely freed object encountered when a
		slab was about to be deactivated. Frozen: How many times was
		free able to skip list processing because the slab was in use
		as the cpuslab of another processor.

Flushes:	Number of times the cpuslab was flushed on request
		(kmem_cache_shrink, may result from races in __slab_alloc)

Refill:		Number of times we were able to refill the cpuslab from
		remotely freed objects for the same slab.

Deactivate:	Statistics how slabs were deactivated. Shows how they were
		put onto the partial list.

In general fastpath is very good. Slowpath without partial list processing is
also desirable. Any touching of partial list uses node specific locks which
may potentially cause list lock contention.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>

Including additional fixes from Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

We have too many section mismatches detected at the moment.
So silence modpost and prevent the option from being
set in a typical allyesconfig build.

Tell the user how to see all the deteils in the summary
message from modpost.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Change latencytop Kconfig entry so it doesn't list the archictectures
that support it. Instead introduce HAVE_LATENCY_SUPPORT which any
architecture can set. Should reduce patch conflicts.

Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Holger Wolf <wolf@linux.vnet.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This patch adds a new configuration option, which adds support for a new
early_param which gets checked in arch/x86/kernel/setup_{32,64}.c:setup_arch()
to decide wether OHCI-1394 FireWire controllers should be initialized and
enabled for physical DMA access to allow remote debugging of early problems
like issues ACPI or other subsystems which are executed very early.

If the config option is not enabled, no code is changed, and if the boot
paramenter is not given, no new code is executed, and independent of that,
all new code is freed after boot, so the config option can be even enabled
in standard, non-debug kernels.

With specialized tools, it is then possible to get debugging information
from machines which have no serial ports (notebooks) such as the printk
buffer contents, or any data which can be referenced from global pointers,
if it is stored below the 4GB limit and even memory dumps of of the physical
RAM region below the 4GB limit can be taken without any cooperation from the
CPU of the host, so the machine can be crashed early, it does not matter.

In the extreme, even kernel debuggers can be accessed in this way. I wrote
a small kgdb module and an accompanying gdb stub for FireWire which allows
to gdb to talk to kgdb using remote remory reads and writes over FireWire.

An version of the gdb stub fore FireWire is able to read all global data
from a system which is running a a normal kernel without any kernel debugger,
without any interruption or support of the system's CPU. That way, e.g. the
task struct and so on can be read and even manipulated when the physical DMA
access is granted.

A HOWTO is included in this patch, in Documentation/debugging-via-ohci1394.txt
and I've put a copy online at
ftp://ftp.suse.de/private/bk/firewire/docs/debugging-via-ohci1394.txt

It also has links to all the tools which are available to make use of it
another copy of it is online at:
ftp://ftp.suse.de/private/bk/firewire/kernel/ohci1394_dma_early-v2.diffSigned-Off-By: NBernhard Kaindl <bk@suse.de>
Tested-By: NThomas Renninger <trenn@suse.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

During the work on the x86 32 and 64 bit backtrace code I found it useful
to have a simple test module to test a process and irq context backtrace.
Since the existing backtrace code was buggy, I figure it might be useful
to have such a test module in the kernel so that maybe we can even
detect such bugs earlier..

[ mingo@elte.hu: build fix ]
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Here is a quick and naive smoke test for kprobes. This is intended to
just verify if some unrelated change broke the *probes subsystem. It is
self contained, architecture agnostic and isn't of any great use by itself.

This needs to be built in the kernel and runs a basic set of tests to
verify if kprobes, jprobes and kretprobes run fine on the kernel. In case
of an error, it'll print out a message with a "BUG" prefix.

This is a start; we intend to add more tests to this bucket over time.

Thanks to Jim Keniston and Masami Hiramatsu for comments and suggestions.

Tested on x86 (32/64) and powerpc.
Signed-off-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: NMasami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

If the config option CONFIG_SECTION_MISMATCH is not set and
we see a Section mismatch present the following to the user:

modpost: Found 1 section mismatch(es).
To see additional details select "Enable full Section mismatch analysis"
in the Kernel Hacking menu (CONFIG_SECTION_MISMATCH).

If the option CONFIG_SECTION_MISMATCH is selected
then be verbose in the Section mismatch reporting from mdopost.
Sample outputs:

WARNING: o-x86_64/vmlinux.o(.text+0x7396): Section mismatch in reference from the function discover_ebda() to the variable .init.data:ebda_addr
The function  discover_ebda() references
the variable __initdata ebda_addr.
This is often because discover_ebda lacks a __initdata
annotation or the annotation of ebda_addr is wrong.

WARNING: o-x86_64/vmlinux.o(.data+0x74d58): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
The variable pci_serial_quirks references
the function __devexit pci_plx9050_exit()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: o-x86_64/vmlinux.o(__ksymtab+0x630): Section mismatch in reference from the variable __ksymtab_arch_register_cpu to the function .cpuinit.text:arch_register_cpu()
The symbol arch_register_cpu is exported and annotated __cpuinit
Fix this by removing the __cpuinit annotation of arch_register_cpu or drop the export.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Setting the option DEBUG_SECTION_MISMATCH will
report additional section mismatch'es but this
should in the end makes it possible to get rid of
all of them.

See help text in lib/Kconfig.debug for details.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

LatencyTOP kernel infrastructure; it measures latencies in the
scheduler and tracks it system wide and per process.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

The __deprecated marker is quite useful in highlighting the remnants of
old APIs that want removing.

However, it is quite normal for one or more years to pass, before the
(usually ancient, bitrotten) code in question is either updated or
deleted.

Thus, like __must_check, add a Kconfig option that permits the silencing
of this compiler warning.

This change mimics the ifdef-ery and Kconfig defaults of MUST_CHECK as
closely as possible.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a Kconfig entry which will toggle some sanity checks on the sg
entry and tables.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Begin infrastructure for kernel code samples in the samples/ directory.
Add its Kconfig and Kbuild files.
Source its Kconfig file in all arch/ Kconfigs.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NMathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Optionally add a boot delay after each kernel printk() call, crudely
measured in milliseconds, with a maximum delay of 10 seconds per printk.

Enable CONFIG_BOOT_PRINTK_DELAY=y and then add (e.g.):
"lpj=loops_per_jiffy boot_delay=100"
to the kernel command line.

It has been useful in cases like "during boot, my machine just reboots or the
screen goes black" by slowing down printk, (and adding initcall_debug), we can
usually see the last thing that happened before the lights went out which is
usually a valuable clue.

[akpm@linux-foundation.org: not all architectures implement CONFIG_HZ]
[akpm@linux-foundation.org: fix lots of stuff]
[bunk@stusta.de: kernel/printk.c: make 2 variables static]
[heiko.carstens@de.ibm.com: fix slow down printk on boot compile error]
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>