>From now on, a port can become a slave of OVS master. All vlans
are enabled, STP state is set to "forwarding". It is up to the OVS
userspace daemon to setup the flows either in kernel or in HW using TC
flower offload.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To find out if a netdev is an OVS port.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far, mlxsw_sp_port_vlan_set range is limited by
MLXSW_REG_SPVM_REC_MAX_COUNT. In spectrum_switchdev code this is
wrapped up by a helper function which actually does multiple calls
to FW for bigger ranges. Move the code into mlxsw_sp_port_vlan_set
and use it always. That allows caller not to care about the range.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW requires the FID to be valid in order for the forward action to work.
So regardless of the current FID validity, just set the dummy FID which
would do the trick.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For forwarding using ACL action, HW needs a valid FID to be setup. It
does not actually use it, so it can be any valid FID. So create a dummy
FID only for this purpose.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement part of multipurpose Virtual Router and Forwarding Domain
Action that takes care of setting up FID. We need to use it to be able
to forward packets using ACL action when no FID is associated on RX.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware has a LPI interrupt.
There is already code in the stmmac driver to parse and handle the
interrupt. However, this information was missing from the DT binding.

At the same time, improve the description of the existing interrupts.
Signed-off-by: NNiklas Cassel <niklas.cassel@axis.com>
Acked-By: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct sock_filter_ext didn't make it into the tree and is now called
struct bpf_insn. Reword the kerneldoc comment for bpf_convert_filter()
accordingly.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2017-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
My last pull request has been a while, we now have:
 * connection quality monitoring with multiple thresholds
 * support for FILS shared key authentication offload
 * pre-CAC regulatory compliance - only ETSI allows this
 * sanity check for some rate confusion that hit ChromeOS
   (but nobody else uses it, evidently)
 * some documentation updates
 * lots of cleanups
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Juergen Borleis says:

====================
net: dsa: add SMSC/Microchip LAN9303 three port ethernet switch driver

The LAN9303 is a three port 10/100 ethernet switch with integrated phys
for the two external ethernet ports. The third port is an RMII/MII
interface to a host master network interface (e.g. fixed link).

While the LAN9303 device itself supports offload packet processing, this
driver does not make use of it yet. This driver just configures the device
to provide two separate network interfaces (which is the default state of
a DSA device).

Please note: the "MDIO managed mode" driver part isn't tested yet. I have
used and tested the "I2C managed mode" only.

Changes in v6:

- fix support to use the driver as a module (core, i2c and mdio)
- license info added in all parts of the driver (for module support)

Changes in v5:

- add missing include file to 'net/dsa/tag_lan9303.c'

Changes in v4:

- rebased on net-next, 'net/dsa/tag_lan9303.c' adapted to changed API

Changes in v3:

- 'ds_to_lan9303()' removed
- special PHY reg MII_LAN911X_SPECIAL_CONTROL_STATUS mapping removed
- compatible strings for I2C and MDIO are now different
- MDIO-managed-mode devicetree binding added (still compile time tested only)

Changes in v2:

- code moved to 'drivers/net/dsa'
- timeouts in completion wait loops
- macros instead of various magic numbers
- development code removed
- devicetree property names changed
- devicetree example adapted
- tried to avoid to mix 'switching' and 'forwarding'...

Comments are welcome.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the LAN9303 device is in MDIO manged mode, all register accesses must
be done via MDIO.

Please note: this code is compile time tested only due to the absence of such
configured hardware. It is based on a patch from Stefan Roese from 2014.
Signed-off-by: NJuergen Borleis <jbe@pengutronix.de>
CC: devicetree@vger.kernel.org
CC: robh+dt@kernel.org
CC: mark.rutland@arm.com
CC: sr@denx.de
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this mode the switch device and the internal phys will be managed via
I2C interface. The MDIO interface is still supported, but for the
(emulated) CPU port only.
Signed-off-by: NJuergen Borleis <jbe@pengutronix.de>
CC: devicetree@vger.kernel.org
CC: robh+dt@kernel.org
CC: mark.rutland@arm.com
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SMSC/Microchip LAN9303 is an ethernet switch device with one CPU port
and two external ethernet ports with built-in phys.

This driver uses the DSA framework, but is currently only capable of
separating the two external ports. There is no offload support yet.
Signed-off-by: NJuergen Borleis <jbe@pengutronix.de>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To define the outgoing port and to discover the incoming port a regular
VLAN tag is used by the LAN9303. But its VID meaning is 'special'.

This tag handler/filter depends on some hardware features which must be
enabled in the device to provide and make use of this special VLAN tag
to control the destination and the source of an ethernet packet.
Signed-off-by: NJuergen Borleis <jbe@pengutronix.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc 4.8.4 complains that mlx4_SW2HW_MPT_wrapper() uses an uninitialized
'mpt' variable:
  drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mlx4_SW2HW_MPT_wrapper':
  drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:2802:12: warning: 'mpt' may be used uninitialized in this function [-Wmaybe-uninitialized]
     mpt->mtt = mtt;

I think this warning is a false complaint.  mpt is only used when
mr_res_start_move_to() return zero, and in all such cases it initializes
mpt.  But apparently gcc cannot see that.

Initialize mpt to avoid the warning.
Signed-off-by: NGreg Thelen <gthelen@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DMA API debugging (when enabled) causes:

WARNING: CPU: 0 PID: 1445 at lib/dma-debug.c:519 add_dma_entry+0xe0/0x12c
DMA-API: exceeded 7 overlapping mappings of cacheline 0x01b2974d

to be  printed after repeated initialization of the Ether device, e.g.
suspend/resume or 'ifconfig' up/down. This is because DMA buffers mapped
using dma_map_single() in sh_eth_ring_format() and sh_eth_start_xmit() are
never unmapped. Resolve this problem by unmapping the buffers when freeing
the descriptor  rings;  in order  to do it right, we'd have to add an extra
parameter to sh_eth_txfree() (we rename this function to sh_eth_tx_free(),
while at it).

Based on the commit a47b70ea ("ravb: unmap descriptors when freeing
rings").
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull sparc fixes from David Miller:
 "Two Sparc bug fixes from Daniel Jordan and Nitin Gupta"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix hugepage page table free
  sparc64: Use LOCKDEP_SMALL, not PROVE_LOCKING_SMALL

Pull networking fixes from David Miller:

 1) BPF tail call handling bug fixes from Daniel Borkmann.

 2) Fix allowance of too many rx queues in sfc driver, from Bert
    Kenward.

 3) Non-loopback ipv6 packets claiming src of ::1 should be dropped,
    from Florian Westphal.

 4) Statistics requests on KSZ9031 can crash, fix from Grygorii
    Strashko.

 5) TX ring handling fixes in mediatek driver, from Sean Wang.

 6) ip_ra_control can deadlock, fix lock acquisition ordering to fix,
    from Cong WANG.

 7) Fix use after free in ip_recv_error(), from Willem de Buijn.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  bpf: fix checking xdp_adjust_head on tail calls
  bpf: fix cb access in socket filter programs on tail calls
  ipv6: drop non loopback packets claiming to originate from ::1
  net: ethernet: mediatek: fix inconsistency of port number carried in TXD
  net: ethernet: mediatek: fix inconsistency between TXD and the used buffer
  net: phy: micrel: fix crash when statistic requested for KSZ9031 phy
  net: vrf: Fix setting NLM_F_EXCL flag when adding l3mdev rule
  net: thunderx: Fix set_max_bgx_per_node for 81xx rgx
  net-timestamp: avoid use-after-free in ip_recv_error
  ipv4: fix a deadlock in ip_ra_control
  sfc: limit the number of receive queues

Make sure the start adderess is aligned to PMD_SIZE
boundary when freeing page table backing a hugepage
region. The issue was causing segfaults when a region
backed by 64K pages was unmapped since such a region
is in general not PMD_SIZE aligned.
Signed-off-by: NNitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_PROVE_LOCKING_SMALL shrinks the memory usage of lockdep so the
kernel text, data, and bss fit in the required 32MB limit, but this
option is not set for every config that enables lockdep.

A 4.10 kernel fails to boot with the console output

    Kernel: Using 8 locked TLB entries for main kernel image.
    hypervisor_tlb_lock[2000000:0:8000000071c007c3:1]: errors with f
    Program terminated

with these config options

    CONFIG_LOCKDEP=y
    CONFIG_LOCK_STAT=y
    CONFIG_PROVE_LOCKING=n

To fix, rename CONFIG_PROVE_LOCKING_SMALL to CONFIG_LOCKDEP_SMALL, and
enable this option with CONFIG_LOCKDEP=y so we get the reduced memory
usage every time lockdep is turned on.

Tested that CONFIG_LOCKDEP_SMALL is set to 'y' if and only if
CONFIG_LOCKDEP is set to 'y'.  When other lockdep-related config options
that select CONFIG_LOCKDEP are enabled (e.g. CONFIG_LOCK_STAT or
CONFIG_PROVE_LOCKING), verified that CONFIG_LOCKDEP_SMALL is also
enabled.

Fixes: e6b5f1be ("config: Adding the new config parameter CONFIG_PROVE_LOCKING_SMALL for sparc")
Signed-off-by: NDaniel Jordan <daniel.m.jordan@oracle.com>
Reviewed-by: NBabu Moger <babu.moger@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The attribute declaration is typically before the definition. Move
the __maybe_unused attribute declaration before the struct keyword.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We disable VxLAN offload when more than 1 UDP port is added to the driver,
since Skyhawk doesn't support offload with multiple ports. The existing
driver design expects the user to delete all port configurations and create
a configuration with a single UDP port for VxLAN offload to be re-enabled.
Remove this restriction by tracking the ports added and re-enabling offload
when ports get deleted and only 1 port is left.
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Reviewed-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds extended statistics reporting to ethtool.

In summary, this patch,

   - adds ethtool.h with the statistics register definitions
   - adds 'struct xge_gstrings_extd_stats' to gather extended stats
   - modifies xge_get_strings(), get_sset_count() and
     get_ethtool_stats() accordingly
   - moves 'struct xge_gstrings_stats' to ethtool.h
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Benjamin Herrenschmidt says:

====================
ftgmac100: Rework batch 5 - Features

This is the third spin of the fifth and last batch of
updates to the ftgmac100 driver.

This contains a few additional "features" such as:

 - Support for ethtool n-way reset
 - Multicast filtering & promisc support
 - Vlan offload
 - netpoll

And a couple of misc bits. This also adds the device-tree binding
documentation.

v2. - Addresses review comments and adds a new patch fixing a
      theorical ordering issue in my new NAPI poll implementation
    - Add a bug fix (Patch 8/9) for a potential ordering issue
      in the new NAPI poll code.

v3. - Rebase on net-next (fix conflict with an unrelated #include
      change series)
    - Update DT bindings better describing accepted phy-mode values
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to ensure the loads from the descriptor are done after the
MMIO store clearing the interrupts has completed, otherwise we
might still miss work.

A read back from the MMIO register will "push" the posted store and
ioread32 has a barrier on weakly aordered architectures that will
order subsequent accesses.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This uses the standard phy-mode property
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just call the interrupt handler with interrupts locally disabled
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The chip supports HW vlan tag insertion and extraction. Add support
for it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the ndo_set_rx_mode() callback to configure the
multicast filters, promisc and allmulti options.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hopefully my understanding of how the hardware works is correct,
as the documentation isn't completely clear. So far I have seen
no obvious issue. Pause seem to also work with NC-SI.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A non-wired up implementation accidentally made its way in
a previous patch (Make ring sizes configurable via ethtool).

This removes it and wires up the generic phy_ethtool_nway_reset
instead.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Markus Elfring says:

====================
Ethernet-Marvell: Fine-tuning for several function implementations

Several update suggestions were taken into account
from static source code analysis.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A string which did not contain a data format specification should be put
into a sequence. Thus use the corresponding function "seq_puts".

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The script "checkpatch.pl" pointed information out like the following.

Comparison to NULL could be written "!skge->mem".

Thus fix the affected source code place.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A string which did not contain a data format specification should be put
into a sequence. Thus use the corresponding function "seq_puts".

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

The script “checkpatch.pl” pointed information out like the following.

Comparison to NULL could be written …

Thus fix the affected source code places.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>