This avoids using the deprecated drm_get_pci_dev() and load() hook
interfaces in the qxl driver.

The only tricky part is to ensure TTM debugfs initialization happens
after the debugfs root node is created, which is done by moving that
code into the debufs_init() hook.

Tested on qemu with igt and running a WM on top of X.

Changes since v1:
 - Drop verification for primary minor in qxl_debugsfs_init.
Changes since V2:
 - Put new header together with other debugfs headers.
Signed-off-by: NGabriel Krisman Bertazi <krisman@collabora.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170119134806.8926-1-krisman@collabora.co.uk

I've found that by just turning the chip on and off via the
POWER_DOWN register, I end up getting i2c_transfer errors on
HiKey.

Investigating further, it turns out that some of the register
state in hardware is getting lost, as the device registers are
reset when the chip is powered down.

Thus this patch simply re-writes the i2c address to the
ADV7511_REG_EDID_I2C_ADDR register to ensure its properly set
before we try to read the EDID data.

Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-7-git-send-email-john.stultz@linaro.org

Thus this patch changes the EDID probing logic so that we
re-use the __adv7511_power_on/off() calls instead of duplciating
logic.

This does change behavior slightly as it adds the HPD signal
pulse to the EDID probe path, but Archit has had a patch to
add HPD signal pulse to the EDID probe path before, so this
should address the cases where that helped. Another difference
is that regcache_mark_dirty() is also called in the power off
path once EDID is probed.

Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-6-git-send-email-john.stultz@linaro.org

In chasing down issues with EDID probing, I found some
duplicated but incomplete logic used to power the chip on and
off.

This patch refactors the adv7511_power_on/off functions, so
they can be used for internal needs.

Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-5-git-send-email-john.stultz@linaro.org

On some adv7511 implementations, we can get some spurious
disconnect signals which can cause monitor probing to fail.

This patch enables HPD (hot plug detect) interrupt support
which allows the monitor to be properly re-initialized when
the spurious disconnect signal goes away.

This also enables proper hotplug support.

Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Originally-by: NArchit Taneja <architt@codeaurora.org>
[jstultz: Added proper commit message]
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-4-git-send-email-john.stultz@linaro.org

In chasing down a previous issue with EDID probing from calling
drm_helper_hpd_irq_event() from irq context, Laurent noticed
that the DRM documentation suggests that
drm_kms_helper_hotplug_event() should be used instead.

Thus this patch replaces drm_helper_hpd_irq_event() with
drm_kms_helper_hotplug_event(), which requires we update the
connector.status entry and only call _hotplug_event() when the
status changes.

Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-3-git-send-email-john.stultz@linaro.org

I was recently seeing issues with EDID probing, where
the logic to wait for the EDID read bit to be set by the
IRQ wasn't happening and the code would time out and fail.

Digging deeper, I found this was due to the fact that
IRQs were disabled as we were running in IRQ context from
the HPD signal.

Thus this patch changes the logic to handle the HPD signal
via a work_struct so we can be out of irq context.

With this patch, the EDID probing on hotplug does not time
out.

Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-2-git-send-email-john.stultz@linaro.org

Use drm_crtc_from_index() to find drm_crtc for given index, so that we
do not need to maintain a pointer array in struct vc4_dev.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1483961145-18453-7-git-send-email-shawnguo@kernel.org

Function tegra_crtc_from_pipe() does the exactly same thing as what
crtc helper drm_crtc_from_index() provides.  Use the helper to save
some code.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1483961145-18453-6-git-send-email-shawnguo@kernel.org

Use drm_crtc_from_index() to find drm_crtc for given index.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1483961145-18453-5-git-send-email-shawnguo@kernel.org

Use drm_crtc_from_index() to find drm_crtc for given index, so that we
do not need to maintain a pointer array in struct mtk_drm_private.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: CK Hu <ck.hu@mediatek.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1483961145-18453-4-git-send-email-shawnguo@kernel.org

Use drm_crtc_from_index() to find drm_crtc for given index, so that we
do not need to maintain a pointer array in struct kirin_drm_private.

Reviewed-by: Xinliang Liu<z.liuxinliang@hisilicon.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1483961145-18453-3-git-send-email-shawnguo@kernel.org

Use drm_crtc_from_index() to find drm_crtc for given index, so that we
do not need to maintain a pointer array in struct exynos_drm_private.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Inki Dae <inki.dae@samsung.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1483961145-18453-2-git-send-email-shawnguo@kernel.org

Make it clear that the core bridge/dw_hdmi.txt document isn't a device
tree binding by itself but is meant to be referenced by platform device
tree bindings, and update the Rockchip and Freescale DWC HDMI TX
bindings to reference it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-21-laurent.pinchart+renesas@ideasonboard.com

According to the PHY IP core vendor, the SVSRET signal must be asserted
before resetting the PHY. Tests on RK3288 and R-Car Gen3 showed no
regression, the change should thus be safe.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-20-laurent.pinchart+renesas@ideasonboard.com

The PHY reset signal is controlled by bit PHYRSTZ in the MC_PHYRSTZ
register. The signal is active low on Gen1 PHYs and active high on Gen2
PHYs. The driver toggles the signal high then low, which is correct for
all currently supported platforms, but the register values macros are
incorrectly named. Replace them with a single macro named after the bit,
and add a comment to the source code to explain the behaviour.

The driver's behaviour isn't changed by this rename, the code will still
need to be fixed to support Gen1 PHYs.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-19-laurent.pinchart+renesas@ideasonboard.com

Replace the hardcoded register address numerical values with macros to
clarify the code.

This change has been tested by comparing the assembly code before and
after the change.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-18-laurent.pinchart+renesas@ideasonboard.com

Detect the PHY type and use it to handle the PHY type-specific SVSRET
signal.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-17-laurent.pinchart+renesas@ideasonboard.com

Use the device version queried at runtime instead of the device type
provided through platform data to handle the overflow workaround. This
will make support of other SoCs integrating the same HDMI TX controller
version easier.

Among the supported platforms only i.MX6DL and i.MX6Q have been
identified as needing the workaround. Disabling it on Rockchip RK3288
(which integrates a v2.00a controller) didn't produce any error or
artifact.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-16-laurent.pinchart+renesas@ideasonboard.com

Bit 0 in CONFIG1_ID tells whether the IP core uses an AHB slave
interface for control. The correct way to identify AHB audio DMA support
is through bit 1 in CONFIG3_ID.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-15-laurent.pinchart+renesas@ideasonboard.com

The DWC HDMI TX can be recognized by the two product identification
registers. If the registers don't read as expect the IP will be very
different than what the driver has been designed for, or will be
misconfigured in a way that makes it non-operational (invalid memory
address, incorrect clocks, ...). We should reject this situation with an
error.

While this isn't critical for proper operation with supported IPs at the
moment, the driver will soon gain automatic device-specific handling
based on runtime device identification. This change makes it easier to
implement that without having to default to a random guess in case the
device can't be identified.

While at it print a readable version number in the device identification
message instead of raw register values.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-14-laurent.pinchart+renesas@ideasonboard.com

The bit is documented in a Rockchip BSP as

 #define m_SVSRET_SIG		(1 << 5) /* depend on PHY_MHL_COMB0=1 */

This is confirmed by a Renesas platform, which uses a 2.0 DWC HDMI TX as
the RK3288. Rename the bit accordingly.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-13-laurent.pinchart+renesas@ideasonboard.com

The current code hard codes the call of hdmi_phy_configure() to be 8bpp
and provides extraneous error checking to verify that this hardcoded
value is correct. Simplify the implementation by removing the argument.
Signed-off-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-12-laurent.pinchart+renesas@ideasonboard.com

As an option for drivers not based on the component framework, register
the bridge with the DRM core with the DRM bridge API. Existing drivers
based on dw_hdmi_bind() and dw_hdmi_unbind() are not affected as those
functions are preserved with their current behaviour.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-11-laurent.pinchart+renesas@ideasonboard.com

The DRM device is not guaranteed by the bridge API to be available
before the attach callback. The driver performs properly at the moment
as it doesn't use the drm_bridge_add() registration method. As this will
be changed later, move connector creation to attach time to ensure
compatibility with the API.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-10-laurent.pinchart+renesas@ideasonboard.com

The next commit will reference structures and functions in a way that
currently requires forward declarations. Reorder the functions to avoid
that. No functional change to the code is performed.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-9-laurent.pinchart+renesas@ideasonboard.com

There's no need to duplicate identical code in multiple drivers (two at
the moment, one more to come soon). Move it to the dw-hdmi core where it
can be shared. If resource allocation ever becomes device-specific later
we'll always have the option of splitting it out again.

While it at pass the platform device to the bind function to avoid
having to cast struct device to struct platform_device.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-8-laurent.pinchart+renesas@ideasonboard.com

Hotplug events should only be forwarded to the DRM core by the interrupt
handler when the bridge has been attached, otherwise the DRM device
pointer will be NULL, resulting in a crash.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-7-laurent.pinchart+renesas@ideasonboard.com

The field isn't needed, remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-6-laurent.pinchart+renesas@ideasonboard.com

The drm_bridge instance is always needed, there's no point in allocating
it separately.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-5-laurent.pinchart+renesas@ideasonboard.com

The 'prep' parameter passed to hdmi_phy_configure() is useless. It is
hardcoded as 0, and if set, simply prevents the configure function from
executing.

Remove it.
Signed-off-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-4-laurent.pinchart+renesas@ideasonboard.com

The master argument isn't used. The data argument, a void pointer, is
used by the bind function only where it's cast to a drm_device pointer,
which can easily be obtained from the encoder argument instead. Remove
them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-3-laurent.pinchart+renesas@ideasonboard.com

The latter is just an int wrapper around the former void function that
unconditionally returns 0. As the return value is never checked, merge
the two functions into one.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-2-laurent.pinchart+renesas@ideasonboard.com

Registering the connector explicitly right after creation is not
necessary for modesetting drivers, because drm_dev_register already takes
care of this on the core side, by calling drm_modeset_register_all.

In addition, performing the initialization too early will get in the way
of the load() hook removal, because the connector interface cannot be
published prior to registering the minors.
Signed-off-by: NGabriel Krisman Bertazi <krisman@collabora.co.uk>
CC: Dave Airlie <airlied@redhat.com>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170112161610.19924-1-krisman@collabora.co.uk

Maintain a table of regulator names expected by ADV7511 and ADV7533.
Use regulator_bulk_* api to configure these.

Initialize and enable the regulators during probe itself. Controlling
these dynamically is left for later.
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484117547-26417-3-git-send-email-architt@codeaurora.org

Add the regulator supply properties needed by ADV7511 and ADV7533.
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484117547-26417-2-git-send-email-architt@codeaurora.org

This is the deprecated function for when you embedded the framebuffer
somewhere else (which breaks refcounting). But Tegra is using
drm_framebuffer_remove and a free-standing FB, so this is redundant.

One caveat here is that the failure path in the init code still
manually cleaned up the fb. I presume that was an oversight and
changed it over to drm_framebuffer_remove too.

Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1482835765-12044-5-git-send-email-daniel.vetter@ffwll.ch
Link: http://patchwork.freedesktop.org/patch/msgid/1482835765-12044-2-git-send-email-daniel.vetter@ffwll.ch

This is the deprecated function for when you embedded the framebuffer
somewhere else (which breaks refcounting). But cma helpers are using
drm_framebuffer_remove and a free-standing fb, so this is rendundant.

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1482835765-12044-2-git-send-email-daniel.vetter@ffwll.ch

This is the deprecated function for when you embedded the framebuffer
somewhere else (which breaks refcounting). But omapdrm is using
drm_framebuffer_remove and a free-standing fb, so this is rendundant.

Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1482835765-12044-4-git-send-email-daniel.vetter@ffwll.ch

DRM_VM and DRM_LEGACY shouldn't be selected if MMU isn't set.

Fixes: 62a0d98a ("drm: allow to use mmuless SoC")
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1484211456-5759-1-git-send-email-benjamin.gaignard@linaro.org