Add KVM_PPC_CPU_CHAR_BCCTR_FLUSH_ASSIST &
KVM_PPC_CPU_BEHAV_FLUSH_COUNT_CACHE to the characteristics returned
from the H_GET_CPU_CHARACTERISTICS H-CALL, as queried from either the
hypervisor or the device tree.
Signed-off-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This adds a one-reg register identifier which can be used to read and
set the virtual PTCR for the guest.  This register identifies the
address and size of the virtual partition table for the guest, which
contains information about the nested guests under this guest.

Migrating this value is the only extra requirement for migrating a
guest which has nested guests (assuming of course that the destination
host supports nested virtualization in the kvm-hv module).
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This adds a new KVM_REG_PPC_ONLINE register which userspace can set
to 0 or 1 via the GET/SET_ONE_REG interface to indicate whether it
considers the VCPU to be offline (0), that is, not currently running,
or online (1).  This will be used in a later patch to configure the
register which controls PURR and SPURR accumulation.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This adds a new ioctl, KVM_PPC_GET_CPU_CHAR, that gives userspace
information about the underlying machine's level of vulnerability
to the recently announced vulnerabilities CVE-2017-5715,
CVE-2017-5753 and CVE-2017-5754, and whether the machine provides
instructions to assist software to work around the vulnerabilities.

The ioctl returns two u64 words describing characteristics of the
CPU and required software behaviour respectively, plus two mask
words which indicate which bits have been filled in by the kernel,
for extensibility.  The bit definitions are the same as for the
new H_GET_CPU_CHARACTERISTICS hypercall.

There is also a new capability, KVM_CAP_PPC_GET_CPU_CHAR, which
indicates whether the new ioctl is available.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This adds a register identifier for use with the one_reg interface
to allow the decrementer expiry time to be read and written by
userspace.  The decrementer expiry time is in guest timebase units
and is equal to the sum of the decrementer and the guest timebase.
(The expiry time is used rather than the decrementer value itself
because the expiry time is not constantly changing, though the
decrementer value is, while the guest vcpu is not running.)

Without this, a guest vcpu migrated to a new host will see its
decrementer set to some random value.  On POWER8 and earlier, the
decrementer is 32 bits wide and counts down at 512MHz, so the
guest vcpu will potentially see no decrementer interrupts for up
to about 4 seconds, which will lead to a stall.  With POWER9, the
decrementer is now 56 bits side, so the stall can be much longer
(up to 2.23 years) and more noticeable.

To help work around the problem in cases where userspace has not been
updated to migrate the decrementer expiry time, we now set the
default decrementer expiry at vcpu creation time to the current time
rather than the maximum possible value.  This should mean an
immediate decrementer interrupt when a migrated vcpu starts
running.  In cases where the decrementer is 32 bits wide and more
than 4 seconds elapse between the creation of the vcpu and when it
first runs, the decrementer would have wrapped around to positive
values and there may still be a stall - but this is no worse than
the current situation.  In the large-decrementer case, we are sure
to get an immediate decrementer interrupt (assuming the time from
vcpu creation to first run is less than 2.23 years) and we thus
avoid a very long stall.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Many user space API headers have licensing information, which is either
incomplete, badly formatted or just a shorthand for referring to the
license under which the file is supposed to be.  This makes it hard for
compliance tools to determine the correct license.

Update these files with an SPDX license identifier.  The identifier was
chosen based on the license information in the file.

GPL/LGPL licensed headers get the matching GPL/LGPL SPDX license
identifier with the added 'WITH Linux-syscall-note' exception, which is
the officially assigned exception identifier for the kernel syscall
exception:

   NOTE! This copyright does *not* cover user programs that use kernel
   services by normal system calls - this is merely considered normal use
   of the kernel, and does *not* fall under the heading of "derived work".

This exception makes it possible to include GPL headers into non GPL
code, without confusing license compliance tools.

Headers which have either explicit dual licensing or are just licensed
under a non GPL license are updated with the corresponding SPDX
identifier and the GPLv2 with syscall exception identifier.  The format
is:
        ((GPL-2.0 WITH Linux-syscall-note) OR SPDX-ID-OF-OTHER-LICENSE)

SPDX license identifiers are a legally binding shorthand, which can be
used instead of the full boiler plate text.  The update does not remove
existing license information as this has to be done on a case by case
basis and the copyright holders might have to be consulted. This will
happen in a separate step.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.  See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: NPhilippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Enhance KVM to cause a guest exit with KVM_EXIT_NMI
exit reason upon a machine check exception (MCE) in
the guest address space if the KVM_CAP_PPC_FWNMI
capability is enabled (instead of delivering a 0x200
interrupt to guest). This enables QEMU to build error
log and deliver machine check exception to guest via
guest registered machine check handler.

This approach simplifies the delivery of machine
check exception to guest OS compared to the earlier
approach of KVM directly invoking 0x200 guest interrupt
vector.

This design/approach is based on the feedback for the
QEMU patches to handle machine check exception. Details
of earlier approach of handling machine check exception
in QEMU and related discussions can be found at:

https://lists.nongnu.org/archive/html/qemu-devel/2014-11/msg00813.html

Note:

This patch now directly invokes machine_check_print_event_info()
from kvmppc_handle_exit_hv() to print the event to host console
at the time of guest exit before the exception is passed on to the
guest. Hence, the host-side handling which was performed earlier
via machine_check_fwnmi is removed.

The reasons for this approach is (i) it is not possible
to distinguish whether the exception occurred in the
guest or the host from the pt_regs passed on the
machine_check_exception(). Hence machine_check_exception()
calls panic, instead of passing on the exception to
the guest, if the machine check exception is not
recoverable. (ii) the approach introduced in this
patch gives opportunity to the host kernel to perform
actions in virtual mode before passing on the exception
to the guest. This approach does not require complex
tweaks to machine_check_fwnmi and friends.
Signed-off-by: NAravinda Prasad <aravinda@linux.vnet.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Its value has never changed; we might as well make it part of the ABI instead
of using the return value of KVM_CHECK_EXTENSION(KVM_CAP_COALESCED_MMIO).

Because PPC does not always make MMIO available, the code has to be made
dependent on CONFIG_KVM_MMIO rather than KVM_COALESCED_MMIO_PAGE_OFFSET.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

This adds two capabilities and two ioctls to allow userspace to
find out about and configure the POWER9 MMU in a guest.  The two
capabilities tell userspace whether KVM can support a guest using
the radix MMU, or using the hashed page table (HPT) MMU with a
process table and segment tables.  (Note that the MMUs in the
POWER9 processor cores do not use the process and segment tables
when in HPT mode, but the nest MMU does).

The KVM_PPC_CONFIGURE_V3_MMU ioctl allows userspace to specify
whether a guest will use the radix MMU or the HPT MMU, and to
specify the size and location (in guest space) of the process
table.

The KVM_PPC_GET_RMMU_INFO ioctl gives userspace information about
the radix MMU.  It returns a list of supported radix tree geometries
(base page size and number of bits indexed at each level of the
radix tree) and the encoding used to specify the various page
sizes for the TLB invalidate entry instruction.

Initially, both capabilities return 0 and the ioctls return -EINVAL,
until the necessary infrastructure for them to operate correctly
is added.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch implements P(Presented)/Q(Queued) states for ICS irqs.

When the interrupt is presented, set P. Present if P was not set.
If P is already set, don't present again, set Q.
When the interrupt is EOI'ed, move Q into P (and clear Q). If it is
set, re-present.

The asserted flag used by LSI is also incorporated into the P bit.

When the irq state is saved, P/Q bits are also saved, they need some
qemu modifications to be recognized and passed around to be restored.
KVM_XICS_PENDING bit set and saved should also indicate
KVM_XICS_PRESENTED bit set and saved. But it is possible some old
code doesn't have/recognize the P bit, so when we restore, we set P
for PENDING bit, too.

The idea and much of the code come from Ben.
Signed-off-by: NLi Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This adds code to handle two new guest-accessible special-purpose
registers on POWER9: TIDR (thread ID register) and PSSCR (processor
stop status and control register).  They are context-switched
between host and guest, and the guest values can be read and set
via the one_reg interface.

The PSSCR contains some fields which are guest-accessible and some
which are only accessible in hypervisor mode.  We only allow the
guest-accessible fields to be read or set by userspace.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

When switching from/to a guest that has a transaction in progress,
we need to save/restore the checkpointed register state.  Although
XER is part of the CPU state that gets checkpointed, the code that
does this saving and restoring doesn't save/restore XER.

This fixes it by saving and restoring the XER.  To allow userspace
to read/write the checkpointed XER value, we also add a new ONE_REG
specifier.

The visible effect of this bug is that the guest may see its XER
value being corrupted when it uses transactions.

Fixes: e4e38121 ("KVM: PPC: Book3S HV: Add transactional memory support")
Fixes: 0a8eccef ("KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Reviewed-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

The existing KVM_CREATE_SPAPR_TCE only supports 32bit windows which is not
enough for directly mapped windows as the guest can get more than 4GB.

This adds KVM_CREATE_SPAPR_TCE_64 ioctl and advertises it
via KVM_CAP_SPAPR_TCE_64 capability. The table size is checked against
the locked memory limit.

Since 64bit windows are to support Dynamic DMA windows (DDW), let's add
@bus_offset and @page_shift which are also required by DDW.
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Move ONE_REG AltiVec support to powerpc generic layer.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Signed-off-by: NBharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Unfortunately, the LPCR got defined as a 32-bit register in the
one_reg interface.  This is unfortunate because KVM allows userspace
to control the DPFD (default prefetch depth) field, which is in the
upper 32 bits.  The result is that DPFD always get set to 0, which
reduces performance in the guest.

We can't just change KVM_REG_PPC_LPCR to be a 64-bit register ID,
since that would break existing userspace binaries.  Instead we define
a new KVM_REG_PPC_LPCR_64 id which is 64-bit.  Userspace can still use
the old KVM_REG_PPC_LPCR id, but it now only modifies those fields in
the bottom 32 bits that userspace can modify (ILE, TC and AIL).
If userspace uses the new KVM_REG_PPC_LPCR_64 id, it can modify DPFD
as well.
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: NAlexander Graf <agraf@suse.de>

We now support SPRG9 for guest, so also add a one reg interface for same
Note: Changes are in bookehv code only as we do not have SPRG9 on booke-pr.
Signed-off-by: NBharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Commit b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8
SPRs") added a definition of KVM_REG_PPC_WORT with the same register
number as the existing KVM_REG_PPC_VRSAVE (though in fact the
definitions are not identical because of the different register sizes.)

For clarity, this moves KVM_REG_PPC_WORT to the next unused number,
and also adds it to api.txt.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

The DABRX (DABR extension) register on POWER7 processors provides finer
control over which accesses cause a data breakpoint interrupt.  It
contains 3 bits which indicate whether to enable accesses in user,
kernel and hypervisor modes respectively to cause data breakpoint
interrupts, plus one bit that enables both real mode and virtual mode
accesses to cause interrupts.  Currently, KVM sets DABRX to allow
both kernel and user accesses to cause interrupts while in the guest.

This adds support for the guest to specify other values for DABRX.
PAPR defines a H_SET_XDABR hcall to allow the guest to set both DABR
and DABRX with one call.  This adds a real-mode implementation of
H_SET_XDABR, which shares most of its code with the existing H_SET_DABR
implementation.  To support this, we add a per-vcpu field to store the
DABRX value plus code to get and set it via the ONE_REG interface.

For Linux guests to use this new hcall, userspace needs to add
"hcall-xdabr" to the set of strings in the /chosen/hypertas-functions
property in the device tree.  If userspace does this and then migrates
the guest to a host where the kernel doesn't include this patch, then
userspace will need to implement H_SET_XDABR by writing the specified
DABR value to the DABR using the ONE_REG interface.  In that case, the
old kernel will set DABRX to DABRX_USER | DABRX_KERNEL.  That should
still work correctly, at least for Linux guests, since Linux guests
cope with getting data breakpoint interrupts in modes that weren't
requested by just ignoring the interrupt, and Linux guests never set
DABRX_BTI.

The other thing this does is to make H_SET_DABR and H_SET_XDABR work
on POWER8, which has the DAWR and DAWRX instead of DABR/X.  Guests that
know about POWER8 should use H_SET_MODE rather than H_SET_[X]DABR, but
guests running in POWER7 compatibility mode will still use H_SET_[X]DABR.
For them, this adds the logic to convert DABR/X values into DAWR/X values
on POWER8.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This adds fields to the struct kvm_vcpu_arch to store the new
guest-accessible SPRs on POWER8, adds code to the get/set_one_reg
functions to allow userspace to access this state, and adds code to
the guest entry and exit to context-switch these SPRs between host
and guest.

Note that DPDES (Directed Privileged Doorbell Exception State) is
shared between threads on a core; hence we store it in struct
kvmppc_vcore and have the master thread save and restore it.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This patch adds the debug stub support on booke/bookehv.
Now QEMU debug stub can use hw breakpoint, watchpoint and
software breakpoint to debug guest.

This is how we save/restore debug register context when switching
between guest, userspace and kernel user-process:

When QEMU is running
 -> thread->debug_reg == QEMU debug register context.
 -> Kernel will handle switching the debug register on context switch.
 -> no vcpu_load() called

QEMU makes ioctls (except RUN)
 -> This will call vcpu_load()
 -> should not change context.
 -> Some ioctls can change vcpu debug register, context saved in vcpu->debug_regs

QEMU Makes RUN ioctl
 -> Save thread->debug_reg on STACK
 -> Store thread->debug_reg == vcpu->debug_reg
 -> load thread->debug_reg
 -> RUN VCPU ( So thread points to vcpu context )

Context switch happens When VCPU running
 -> makes vcpu_load() should not load any context
 -> kernel loads the vcpu context as thread->debug_regs points to vcpu context.

On heavyweight_exit
 -> Load the context saved on stack in thread->debug_reg

Currently we do not support debug resource emulation to guest,
On debug exception, always exit to user space irrespective of
user space is expecting the debug exception or not. If this is
unexpected exception (breakpoint/watchpoint event not set by
userspace) then let us leave the action on user space. This
is similar to what it was before, only thing is that now we
have proper exit state available to user space.
Signed-off-by: NBharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

"ehpriv 1" instruction is used for setting software breakpoints
by user space. This patch adds support to exit to user space
with "run->debug" have relevant information.

As this is the first point we are using run->debug, also defined
the run->debug structure.
Signed-off-by: NBharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This enables us to use the Processor Compatibility Register (PCR) on
POWER7 to put the processor into architecture 2.05 compatibility mode
when running a guest.  In this mode the new instructions and registers
that were introduced on POWER7 are disabled in user mode.  This
includes all the VSX facilities plus several other instructions such
as ldbrx, stdbrx, popcntw, popcntd, etc.

To select this mode, we have a new register accessible through the
set/get_one_reg interface, called KVM_REG_PPC_ARCH_COMPAT.  Setting
this to zero gives the full set of capabilities of the processor.
Setting it to one of the "logical" PVR values defined in PAPR puts
the vcpu into the compatibility mode for the corresponding
architecture level.  The supported values are:

0x0f000002	Architecture 2.05 (POWER6)
0x0f000003	Architecture 2.06 (POWER7)
0x0f100003	Architecture 2.06+ (POWER7+)

Since the PCR is per-core, the architecture compatibility level and
the corresponding PCR value are stored in the struct kvmppc_vcore, and
are therefore shared between all vcpus in a virtual core.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
[agraf: squash in fix to add missing break statements and documentation]
Signed-off-by: NAlexander Graf <agraf@suse.de>

POWER7 and later IBM server processors have a register called the
Program Priority Register (PPR), which controls the priority of
each hardware CPU SMT thread, and affects how fast it runs compared
to other SMT threads.  This priority can be controlled by writing to
the PPR or by use of a set of instructions of the form or rN,rN,rN
which are otherwise no-ops but have been defined to set the priority
to particular levels.

This adds code to context switch the PPR when entering and exiting
guests and to make the PPR value accessible through the SET/GET_ONE_REG
interface.  When entering the guest, we set the PPR as late as
possible, because if we are setting a low thread priority it will
make the code run slowly from that point on.  Similarly, the
first-level interrupt handlers save the PPR value in the PACA very
early on, and set the thread priority to the medium level, so that
the interrupt handling code runs at a reasonable speed.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This adds the ability to have a separate LPCR (Logical Partitioning
Control Register) value relating to a guest for each virtual core,
rather than only having a single value for the whole VM.  This
corresponds to what real POWER hardware does, where there is a LPCR
per CPU thread but most of the fields are required to have the same
value on all active threads in a core.

The per-virtual-core LPCR can be read and written using the
GET/SET_ONE_REG interface.  Userspace can can only modify the
following fields of the LPCR value:

DPFD	Default prefetch depth
ILE	Interrupt little-endian
TC	Translation control (secondary HPT hash group search disable)

We still maintain a per-VM default LPCR value in kvm->arch.lpcr, which
contains bits relating to memory management, i.e. the Virtualized
Partition Memory (VPM) bits and the bits relating to guest real mode.
When this default value is updated, the update needs to be propagated
to the per-vcore values, so we add a kvmppc_update_lpcr() helper to do
that.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
[agraf: fix whitespace]
Signed-off-by: NAlexander Graf <agraf@suse.de>

The VRSAVE register value for a vcpu is accessible through the
GET/SET_SREGS interface for Book E processors, but not for Book 3S
processors.  In order to make this accessible for Book 3S processors,
this adds a new register identifier for GET/SET_ONE_REG, and adds
the code to implement it.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This allows guests to have a different timebase origin from the host.
This is needed for migration, where a guest can migrate from one host
to another and the two hosts might have a different timebase origin.
However, the timebase seen by the guest must not go backwards, and
should go forwards only by a small amount corresponding to the time
taken for the migration.

Therefore this provides a new per-vcpu value accessed via the one_reg
interface using the new KVM_REG_PPC_TB_OFFSET identifier.  This value
defaults to 0 and is not modified by KVM.  On entering the guest, this
value is added onto the timebase, and on exiting the guest, it is
subtracted from the timebase.

This is only supported for recent POWER hardware which has the TBU40
(timebase upper 40 bits) register.  Writing to the TBU40 register only
alters the upper 40 bits of the timebase, leaving the lower 24 bits
unchanged.  This provides a way to modify the timebase for guest
migration without disturbing the synchronization of the timebase
registers across CPU cores.  The kernel rounds up the value given
to a multiple of 2^24.

Timebase values stored in KVM structures (struct kvm_vcpu, struct
kvmppc_vcore, etc.) are stored as host timebase values.  The timebase
values in the dispatch trace log need to be guest timebase values,
however, since that is read directly by the guest.  This moves the
setting of vcpu->arch.dec_expires on guest exit to a point after we
have restored the host timebase so that vcpu->arch.dec_expires is a
host timebase value.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This reserves space in get/set_one_reg ioctl for the extra guest state
needed for POWER8.  It doesn't implement these at all, it just reserves
them so that the ABI is defined now.

A few things to note here:

- This add *a lot* state for transactional memory.  TM suspend mode,
  this is unavoidable, you can't simply roll back all transactions and
  store only the checkpointed state.  I've added this all to
  get/set_one_reg (including GPRs) rather than creating a new ioctl
  which returns a struct kvm_regs like KVM_GET_REGS does.  This means we
  if we need to extract the TM state, we are going to need a bucket load
  of IOCTLs.  Hopefully most of the time this will not be needed as we
  can look at the MSR to see if TM is active and only grab them when
  needed.  If this becomes a bottle neck in future we can add another
  ioctl to grab all this state in one go.

- The TM state is offset by 0x80000000.

- For TM, I've done away with VMX and FP and created a single 64x128 bit
  VSX register space.

- I've left a space of 1 (at 0x9c) since Paulus needs to add a value
  which applies to POWER7 as well.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This adds the API for userspace to instantiate an XICS device in a VM
and connect VCPUs to it.  The API consists of a new device type for
the KVM_CREATE_DEVICE ioctl, a new capability KVM_CAP_IRQ_XICS, which
functions similarly to KVM_CAP_IRQ_MPIC, and the KVM_IRQ_LINE ioctl,
which is used to assert and deassert interrupt inputs of the XICS.

The XICS device has one attribute group, KVM_DEV_XICS_GRP_SOURCES.
Each attribute within this group corresponds to the state of one
interrupt source.  The attribute number is the same as the interrupt
source number.

This does not support irq routing or irqfd yet.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This adds the ability for userspace to save and restore the state
of the XICS interrupt presentation controllers (ICPs) via the
KVM_GET/SET_ONE_REG interface.  Since there is one ICP per vcpu, we
simply define a new 64-bit register in the ONE_REG space for the ICP
state.  The state includes the CPU priority setting, the pending IPI
priority, and the priority and source number of any pending external
interrupt.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

For pseries machine emulation, in order to move the interrupt
controller code to the kernel, we need to intercept some RTAS
calls in the kernel itself.  This adds an infrastructure to allow
in-kernel handlers to be registered for RTAS services by name.
A new ioctl, KVM_PPC_RTAS_DEFINE_TOKEN, then allows userspace to
associate token values with those service names.  Then, when the
guest requests an RTAS service with one of those token values, it
will be handled by the relevant in-kernel handler rather than being
passed up to userspace as at present.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
[agraf: fix warning]
Signed-off-by: NAlexander Graf <agraf@suse.de>

Now that all pieces are in place for reusing generic irq infrastructure,
we can copy x86's implementation of KVM_IRQ_LINE irq injection and simply
reuse it for PPC, as it will work there just as well.
Signed-off-by: NAlexander Graf <agraf@suse.de>

Now that all the irq routing and irqfd pieces are generic, we can expose
real irqchip support to all of KVM's internal helpers.

This allows us to use irqfd with the in-kernel MPIC.
Signed-off-by: NAlexander Graf <agraf@suse.de>

Hook the MPIC code up to the KVM interfaces, add locking, etc.
Signed-off-by: NScott Wood <scottwood@freescale.com>
[agraf: add stub function for kvmppc_mpic_set_epr, non-booke, 64bit]
Signed-off-by: NAlexander Graf <agraf@suse.de>

EPTCFG register defined by E.PT is accessed unconditionally by Linux guests
in the presence of MAV 2.0. Emulate it now.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Add support for TLBnPS registers available in MMU Architecture Version
(MAV) 2.0.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

MMU registers were exposed to user-space using sregs interface. Add them
to ONE_REG interface using kvmppc_get_one_reg/kvmppc_set_one_reg delegation
mechanism.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This patch defines the interface parameter for KVM_SET_GUEST_DEBUG
ioctl support. Follow up patches will use this for setting up
hardware breakpoints, watchpoints and software breakpoints.

Also kvm_arch_vcpu_ioctl_set_guest_debug() is brought one level below.
This is because I am not sure what is required for book3s. So this ioctl
behaviour will not change for book3s.
Signed-off-by: NBharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This patch adds the one_reg interface to get the special instruction
to be used for setting software breakpoint from userspace.
Signed-off-by: NBharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

If userspace wants to change some specific bits of TSR
(timer status register) then it uses GET/SET_SREGS ioctl interface.
So the steps will be:
      i)   user-space will make get ioctl,
      ii)  change TSR in userspace
      iii) then make set ioctl.
It can happen that TSR gets changed by kernel after step i) and
before step iii).

To avoid this we have added below one_reg ioctls for oring and clearing
specific bits in TSR. This patch adds one registerface for:
     1) setting specific bit in TSR (timer status register)
     2) clearing specific bit in TSR (timer status register)
     3) setting/getting the TCR register. There are cases where we want to only
        change TCR and not TSR. Although we can uses SREGS without
        KVM_SREGS_E_UPDATE_TSR flag but I think one reg is better. I am open
        if someone feels we should use SREGS only here.
     4) getting/setting TSR register
Signed-off-by: NBharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>