One instance of DRM_DEBUG_KMS was leftover in dp_link_training, convert
it to the new shiny.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210310214845.29021-2-sean@poorly.run

This patch adds some newlines which are missing from debug messages.
This will prevent logs from being stacked up in dmesg.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210310214845.29021-1-sean@poorly.run

SAMPLE_OA parameter enables sampling of OA buffer and results in a call
to init the OA buffer which initializes the OA unit head/tail pointers.
The OA_EXPONENT parameter controls the periodicity of the OA reports in
the OA buffer and results in starting a hrtimer.

Before gen12, all use cases required the use of the OA buffer and i915
enforced this setting when vetting out the parameters passed. In these
platforms the hrtimer was enabled if OA_EXPONENT was passed. This worked
fine since it was implied that SAMPLE_OA is always passed.

With gen12, this changed. Users can use perf without enabling the OA
buffer as in OAR use cases. While an OAR use case should ideally not
start the hrtimer, we see that passing an OA_EXPONENT parameter will
start the hrtimer even though SAMPLE_OA is not specified. This results
in an uninitialized OA buffer, so the head/tail pointers used to track
the buffer are zero.

This itself does not fail, but if we ran a use-case that SAMPLED the OA
buffer previously, then the OA_TAIL register is still pointing to an old
value. When the timer callback runs, it ends up calculating a
wrong/large number of available reports. Since we do a spinlock_irq_save
and start processing a large number of reports, NMI watchdog fires and
causes a crash.

Start the timer only if SAMPLE_OA is specified.

v2:
- Drop SAMPLE OA check when appending samples (Ashutosh)
- Prevent read if OA buffer is not being sampled

Fixes: 00a7f0d7 ("drm/i915/tgl: Add perf support on TGL")
Signed-off-by: NUmesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210305210947.58751-1-umesh.nerlige.ramappa@intel.com

Rename a bunch of the skl+ watermark struct members to
have sensible names. Avoids me having to think what
plane_res_b/etc. means.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210305153610.12177-7-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Make the code more typo proof by extracting small helpers that
do the "do we have enough DDB for the WM level?" checks in
a consistent manner.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210305153610.12177-6-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Let's make all the "do we have enough DDB for this WM level?"
checks use min_ddb_alloc. To achieve that we need to populate
this for the transition watermarks as well.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210305153610.12177-5-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

For non-transition watermarks we are supposed to check min_ddb_alloc
rather than plane_res_b when determining if we have enough DDB space
for it. A bit too much copy pasta made me check the wrong thing.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: df4a50a3 ("drm/i915: Zero out SAGV wm when we don't have enough DDB for it")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210305153610.12177-4-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Say we have two planes enabled with watermarks configured
as follows:
plane A: wm0=enabled/can_sagv=false, wm1=enabled/can_sagv=true
plane B: wm0=enabled/can_sagv=true,  wm1=disabled

This is possible since the latency we use to calculate
can_sagv may not be the same for both planes due to
skl_needs_memory_bw_wa().

In this case skl_crtc_can_enable_sagv() will see that
both planes have enabled at least one watermark level
with can_sagv==true, and thus proceeds to allow SAGV.
However, since plane B does not have wm1 enabled
plane A can't actually use it either. Thus we are
now running with SAGV enabled, but plane A can't
actually tolerate the extra latency it imposes.

To remedy this only allow SAGV on if the highest common
enabled watermark level for all active planes can tolerate
the extra SAGV latency.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210305153610.12177-3-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

On HSW/BDW with VT-d active the first tile row scanned out
after the first async flip of the frame often ends up corrupted.

Whether the corruption happens or not depends on the scanline
on which the async flip happens, but the behaviour seems very
consistent. Ie. the same set of scanlines (which are most scanlines)
always show the corruption. And another set of scanlines (far less
of them) never shows the corruption.

I discovered that disabling the fetch-stride stretching
feature cures the corruption. This is some kind of TLB related
prefetch thing AFAIK. We already disable it on SNB primary
planes due to a documented workaround. The hardware folks
indicated that disabling this should be fine, so let's go
with that.

And while we're here, let's document the relevant bits on all
pre-skl platforms.

Fixes: 2a636e24 ("drm/i915: Implement async flip for ivb/hsw")
Fixes: cda195f1 ("drm/i915: Implement async flips for bdw")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210220103303.3448-1-ville.syrjala@linux.intel.comReviewed-by: NKarthik B S <karthik.b.s@intel.com>

Let's check that we actually found the PLL before doing the
port_clock readout, just in case the hardware was severly
misprogrammed by the previous guy. Not sure the hw would
even survive such misprogramming without hanging but no
real harm in checking anyway.

Cc: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210310194351.6233-1-ville.syrjala@linux.intel.comReviewed-by: NKarthik B S <karthik.b.s@intel.com>

Now that all the encoder clock stuff is uniformly abstracted
for all hsw+ platforms, let's extend icl_sanitize_encoder_pll_mapping()
to cover all of them.

Not sure there is a particular benefit in doing so, but less special
cases always makes me happy.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-7-ville.syrjala@linux.intel.comReviewed-by: NMika Kahola <mika.kahola@intel.com>

Support reading out the current state of the DDI clock.

Not sure we really want this. Seems a bit excessive just to
restore the debug print to icl_sanitize_encoder_pll_mapping()?
But maybe there's more use for it?
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-6-ville.syrjala@linux.intel.comReviewed-by: NMika Kahola <mika.kahola@intel.com>

Move the *_get_ddi_pll() stuff into the encodet->get_config() hook.
There it neatly sits next to the matching .{enable,disable}_clock()
functions.

In order to avoid excessive boilerplate I changed the behaviour
such that all platforms now do the readout via
crtc_state->port_dpll[].

ICL+ TC is still a bit special due to TBTPLL not having a functional
.get_freq(). Should probably change that by adopting the LCPLL
approach, but that would require a fairly substantial rework of the
DPLL ID handling. So leave it for later.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-5-ville.syrjala@linux.intel.comReviewed-by: NMika Kahola <mika.kahola@intel.com>

All the other places we have use pipes instead of crtc indices
when tracking resource usage. Life is easier when we do it
the same way always, so switch the dpll mgr to using pipes as
well. Looks like it was actually mixing these up in some cases
so it would not even have worked correctly except when the
device has a contiguous set of pipes starting from pipe A.
Granted, that is the typical case but supposedly it may not
always hold on modern hw.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-4-ville.syrjala@linux.intel.comReviewed-by: NMika Kahola <mika.kahola@intel.com>

The clock readout for DDI encoders needs to moved into the encoders.
To that end intel_dpll_readout_hw_state() needs to happen after
the encoder readout as otherwise it can't correctly populate
the PLL crtc_mask/active_mask bitmasks.

v2: Populate DPLL ref clocks before the encoder->get_config()
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210225161225.30746-1-ville.syrjala@linux.intel.comReviewed-by: NMika Kahola <mika.kahola@intel.com>

Stop assuming intel_ddi_get_config() is all we need from the primary
encoder, and instead call it via the .get_config() vfunc. This
will allow customized .get_config() for the primary, which I plan
to use to handle the differences in the clock readout between various
platforms.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-2-ville.syrjala@linux.intel.comReviewed-by: NMika Kahola <mika.kahola@intel.com>

commit 33267703 ("drm/i915/dsi: Enable software vblank counter")
claims to get the mode_flags from the crtc_state, but in fact does
not. Fix it to do it right.

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210304170421.10901-5-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

We print the scanline counters as unsigned integers so the -1
here just makes the debugs/traces look a bit messy. Zero seems
equally valid for this usecase.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210304170421.10901-4-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

For platforms/outputs without hardware frame counters we can't
call drm_crtc_accurate_vblank_count() when the vblank support is
disabled or we just get a WARN due to the crtc timings
(vblank->hwmode) being considered invalid. Note that until the
pipe in question has been enabled and drm_crtc_set_max_vblank_count()
has been called on it we would also take this path on platforms
which have a working frame counter. So getting the WARN is rather
likely on any platform unless you always boot with lots of displays
plugged in.

Also even on hardware with a working frame counter we may not be
able to read the actual frame counter register on disabled pipes
due the relevant power well being disabled. Ie. would just result
in the unclaimed reg spew.

So let's just avoid all this an directly report zero in case
the pipe is disabled.
Reported-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
Tested-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210304170421.10901-3-ville.syrjala@linux.intel.comSigned-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

On platforms/outputs without a working frame counter we rely
on the vblank code to cook up the frame counter from the timestamps.
That requires that vblank support is enabled. Thus we need to
move the pipe enable/disable tracepoints to the other side
of the drm_vblank_{on,off}() calls. There shouldn't really be
much happening between these old and new call sites so the
tracepoints should still provide reasonable data.

The alternative would be to give up on having the frame counter
values in the trace which would render the tracepoints more or
less pointless.

v2: Missed one case in intel_ddi_post_disable()
    Drop the now useless i915_trace.h includes
Reported-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
Tested-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210304170421.10901-2-ville.syrjala@linux.intel.comSigned-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

If the source and sink support MSO, enable it during link training.

v4: Divide DRRS pixel clock by link count before M/N calculation

v3: Adjust timings, refer to splitter

v2: Limit MSO to pipe A using ->pipe_mask

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2711
Cc: Nischal Varide <nischal.varide@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/66da48b4b3c5ccffaac7989097cd96d6c6af8243.1614682842.git.jani.nikula@intel.com

In the case of MSO (Multi-SST Operation), the EDID contains the timings
for a single panel segment. We'll want to hide the fact from userspace,
and expose modes that span the entire display.

Don't modify the EDID, as the userspace should not use that for
modesetting, only modify the actual modes.

v3: Use pixel overlap if available.

v2: Rename intel_dp_mso_mode_fixup -> intel_edp_mso_mode_fixup

Cc: Nischal Varide <nischal.varide@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2862284eb033bb0ffc96134b7d5b11bf29e4587f.1614682842.git.jani.nikula@intel.com

For starters, we expect the state to be zero, as we don't enable MSO
anywhere.

v2: Refer to splitter.

Cc: Nischal Varide <nischal.varide@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/459a332f3cdce941c57312150872559db68f88c1.1614682842.git.jani.nikula@intel.com

Add splitter configuration to crtc state, and read it where
supported. Also add splitter state dumping. The stream splitter will be
required for eDP MSO.

v4:
- Catch invalid splitter configuration (Uma)

v3:
- Convert segment timings to full panel timings.
- Refer to splitter instead of mso in crtc state.
- Dump splitter state.

v2: Add warning for mso being enabled on pipes other than A.

Cc: Nischal Varide <nischal.varide@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/95cbe1c9d45edf3e3ec252e49fb49055def98155.1614682842.git.jani.nikula@intel.com

the register offset isn't needed division by 4 to pass RREG32_PCIE()
Signed-off-by: NKevin Wang <kevin1.wang@amd.com>
Reviewed-by: NLijo Lazar <lijo.lazar@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Currently if stream->signal is neither SIGNAL_TYPE_DISPLAY_PORT_MST or
SIGNAL_TYPE_DISPLAY_PORT then variable ret is uninitialized and this is
checked for > 0 at the end of the function.  Ret should be initialized,
I believe setting it to zero is a correct default.

Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: bd0c064c ("drm/amd/display: Add return code instead of boolean for future use")
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

It works fine and was only disabled because primary GPUs
don't enter runpm if there is a console bound to the fbdev due
to the kmap.  This will at least allow runpm on secondary cards.
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NRajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Arcturus has a different register address from other SMU V11
ASICs.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Acked-by: NGuchun Chen <guchun.chen@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Per discussions with PMFW team, the driver only needs to
notify the PMFW when the RLC is disabled.  The RLC FW will notify
the PMFW directly when it's enabled.
Acked-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Making them an error confuses users and the errors are harmless
as not all asics support all profiles.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1488Acked-by: NNirmoy Das <nirmoy.das@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Navi12 0x7360/C7 SKU has no video support, so remove it.
Reviewed-by: NGuchun Chen <guchun.chen@amd.com>
Signed-off-by: NAsher.Song <Asher.Song@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The S0ix check only makes sense if the AMD PMC driver is
present.  We need to use the legacy S3 pathes when the
PMC driver is not present.
Reviewed-by: NPrike Liang <Prike.Liang@amd.com>
Reviewed-by: NRajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Get rid of the nonsense cursor special case in verify_wm_state()
by just iterating through all the planes. And let's use the
canonical [PLANE:..] style in the debug prints while at it.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226153204.1270-8-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

We know which WM0 (normal vs. SAGV) we supposedly programmed
into the hardware, so just check against that instead of accepting
either watermark as valid.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226153204.1270-7-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Seems to me that if we calculate WM0 using the bumped up SAGV latency
we need to calculate the transition watermark accordingly. Track it
alongside the other watermarks.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226153204.1270-6-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

We'll want a SAGV transition watermark as well. Prepare
for that by collecting SAGV wm0 into a sub-strcture.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226153204.1270-5-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Let's consider sagv_wm0 as well when deciding whether to dump
out the watermark changes.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226153204.1270-4-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Let's handle the SAGV WM0 more like the other wm levels and just
totally zero it out when we don't have the DDB space to back it
up.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226153204.1270-3-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

When we switch between SAGV on vs. off we need to reprogram all
plane wateramrks accordingly. Currently skl_wm_add_affected_planes()
totally ignores the SAGV watermark and just assumes we will use
the normal WM0.

Fix this by utilizing skl_plane_wm_level() which picks the
correct watermark based on use_sagv_wm. Thus we will force
an update on all the planes whose watermark registers need
to be reprogrammed.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226153204.1270-2-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Populate conn_state->max_bpc with something sensible from the start.
Otherwise it's possible that we get to compute_sink_pipe_bpp() with
max_bpc==0.

The specific scenario goes as follows:
1. Initial connector state allocated with max_bpc==0
2. Trigger a modeset on the crtc feeding the connector, without
   actually adding the connector to the commit
3. drm_atomic_connector_check() is skipped because the
   connector has not yet been added, hence conn_state->max_bpc
   retains its current value
4. drm_atomic_helper_check_modeset() ->
   drm_atomic_add_affected_connectors() -> the connector
   is now part of the commit
5. compute_baseline_pipe_bpp() -> MISSING_CASE(max_bpc==0)

Note that pipe_bpp itself may not be populated on pre-g4x machines,
in which case we just fall back to max_bpc==8 and let .compute_config()
limit the resulting pipe_bpp further if necessary.

Cc: Daniel Vetter <daniel@ffwll.ch>
Reported-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210216160035.4780-1-ville.syrjala@linux.intel.comTested-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>