There are 5 DDI ports on Haswell. Port A is always enabled, and is the one
connected to eDP, and Port E is the one that can be connected to the PCH
using FDI protocol.  Ports B, C, D and E can be used for digital outputs.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This defines the registers used by different power wells.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This adds product definitions for desktop, mobile and server boards.

v2: split into a separate patch, add .has_pch_split feature.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The macro is becoming too complex and with VLV upon us it can lead to
confusion. So transforming this into a feature check instead.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: fixed conflict with is_valleyview addition.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Haven't seen this yet, but it doesn't hurt.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

ValleyView has a new interrupt architecture; best to put it in a new set
of functions.  Also make sure the ring mask functions handle ValleyView.

FIXME: fix flipping; need to enable interrupts and call prepare/finish
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

ValleyView handles force wake differently than previous chipsets, so add
a couple of new functions for it.  But leave it disabled by default
until we test it (need a chip with the Punit enabled first).
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... and bind it right to the PCI id.

Note that there are still a few things to fix here:
- we need to move the tlb flush to a better place in drm/i915.
- we need to check snoop support on vlv and implement it.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: squash follow-on patch and add todo items to commit msg.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to flush the Gunit TLB when we update GTT PTEs on VLV, but the
register for doing so is above the range we normally map.  Map the whole
register space to make sure we can get it.

v2: only map the larger space on gen7+ (Daniel)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

HDMI register offsets are different in Valleyview. Add support for the
same.

v2: drop superfluous comments in HDMI init (Daniel)
Signed-off-by: NBeeresh G <beeresh.g@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: NJesse Barnes <jesse.barnes@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch adds support for programming drain latency registers of Pondicherry
memory arbiter of Valleyview.

v2: clarify function names (Daniel)
    fix summary typo (Daniel)
v3: add parens (Ben)
    make drain function return bool (Ben)
Acked-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NGajanan Bhat <gajanan.bhat@intel.com>
Reviewed-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: NJesse Barnes <jesse.barnes@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Set required clock gating and chicken bits on VLV.

v2: set PIXEL_SUBSPAN_COLLECT_OPT_DISABLE too (Ben)
    move function below ivb version to pretend to be consistent (Ben)
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

ValleyView puts some display related registers like the PLL controls and
dividers behind the DPIO bus.  Add simple indirect register access
routines to get to those registers.

v2: move new wait_for macro to intel_drv.h (Ben)
    fix DPIO_PKT double write (Ben)
    add debugfs file
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add register definitions for the new VLV PLL bits.

v2: remove unused bits & regs (Ben)
Acked-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add support for ValleyView watermark handling.

v2: remove unused reg & bit definitions (Ben)
Acked-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For use by the rest of the ValleyView code.

v2: fix desktop variant to not set is_mobile (Ben)
Acked-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Makes it more readable and maintainable.  ValleyView will add its own
PLL update function in a later patch.

v2: split LVDS bits out of this patch (Daniel)
v3: fix dropped DP dithering hunk (Daniel)
Acked-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
danvet:
- fixup spurious whitespace change
- reorder patches to fix bisect breakage
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just to make things clearer and reduce the size of this monstrosity.

v2: make sure 8xx PLL update function calls update_lvds too (Daniel)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
danvet: fixed patch ordering to avoid breaking bisect.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Fixes a regression from 9e984bc1 (drm/i915: Don't do MTRR setup if PAT
is enabled) where we left the MTRR as 0 and so tried to free a MTRR we
did not own during unload.
Reported-and-tested-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This memory is always allocated, and it is always a fixed size, so just
allocate it along with the rest of the driver state.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is no GMBUS "disabled" port 0, nor "reserved" port 7.
For the other 6 ports there is a fixed 1:1 mapping between pin pairs and
gmbus ports, which means every real gmbus port has a gpio pin.

Given these realizations, clean up gmbus initialization.

Tested on Sandybridge (gen 6, PCH == CougarPoint) hardware.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of letting other modules directly access the ->gmbus array,
introduce intel_gmbus_get_adapter() for looking up an i2c_adapter
for a given gmbus port identifier.  This will enable later refactoring
of the gmbus port list.

Note: Before requesting an adapter for a given gmbus port number, the
driver must first check its validity using i2c_intel_gmbus_is_port_valid().
If this check fails, a call to intel_gmbus_get_adapter() will WARN_ON and
return NULL.  This is relevant for parts of the driver that read a port
from VBIOS, which might be improperly initialized and contain an invalid
port.  In these cases, the driver must fall back to using a safer default
port.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of rolling our own custom quirk_xfer function, use the bit_algo
pre_xfer and post_xfer functions to setup and teardown bit-banged
i2c transactions.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to i915 documentation [1], "Port D" (DP/HDMI Port D) is
actually gmbus pin pair 6 (gmbus0.2:0 == 110b GPIOF), not 7 (111b).
Pin pair 7 is a reserved pair.

[1] Documentation for [DevSNB+] and [DevIBX], as found on
http://intellinuxgraphics.org:

[DevSNB+]:
http://intellinuxgraphics.org/documentation/SNB/IHD_OS_Vol3_Part3.pdf
 Section 2.2.2 lists the 6 gmbus ports (gpio pin pairs):
    [ 5: HDMI/DPD, 4: HDMIB, 3: HDMI/DPC, 2: LVDS, 1: SSC, 0: VGA ]
 2.2.2.1 lists the GPIO registers to control these 6 ports.
 2.2.3.1 lists the mapping between 5 of these gmbus ports and the 3
 Pin_Pair_Select bits (of the GMBUS0 register).  This table is missing
 HDMIB (port 101).

[DevIBX]: http://intellinuxgraphics.org/IHD_OS_Vol3_Part3r2.pdf
 Section 2.2.2 lists the same 6 gmbus ports plus two 'reserved' gpio
 ports.
 2.2.2.1 lists 8 GPIO registers... however, it says the size of the
 block is 6x32, which implies that those 2 reserved GPIO registers
 (GPIO_6 & GPIO_7) don't actually exist (or are irrelevant).
 2.2.3.1 lists the mapping between the 6 named gmbus ports and the 3
 Pin_Pair_Select bits (of the GMBUS0 register).  This table has HDMIB.

Note: the "reserved" and "disabled" pairs do not actually map to a
physical pair of pins, nor GPIO regs and shouldn't be initialized or used.
Fixing this is left for a later patch.

This bug had not been noticed earlier for two reasons:
 1) Until recently, "gmbus" mode was disabled - all transfers actually
    used "bit-bang" mode on GPIO port 5 (the "HDMI/DPD CTLDATA/CLK"
    pair), at register 0x5024 (defined as GPIOF i915_reg.h).
    Since this is the correct pair of pins for HDMI1, transfers succeed.

 2) Even if gmbus mode is re-enabled, the first attempted transaction
    will fail because it tries to use the wrong ("Reserved") pin pair.
    However, the driver immediately falls back again to the bit-bang
    method, which correctly uses GPIOF, so again, transfers succeed.

However, if gmbus mode is re-enabled and the GPIO fall-back mode is
disabled, then reading an attached monitor's EDID fail.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Split out gmbus_xfer_read/write() helper functions.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Beside helping the compiler untangle this maze they double-up as
documentation for which parts of the code aren't performance-critical
but just around to keep old (but already dead-slow) userspace from
breaking.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The issue is that with inline clflushing the clflushing isn't properly
swizzled. Fix this by
- always clflushing entire 128 byte chunks and
- unconditionally flush before writes when swizzling a given page.
  We could be clever and check whether we pwrite a partial 128 byte
  chunk instead of a partial cacheline, but I've figured that's not
  worth it.

Now the usual approach is to fold this into the original patch series, but
I've opted against this because
- this fixes a corner case only very old userspace relies on and
- I'd like to not invalidate all the testing the pwrite rewrite has gotten.

This fixes the regression notice by tests/gem_tiled_partial_prite_pread
from i-g-t. Unfortunately it doesn't fix the issues with partial pwrites to
tiled buffers on bit17 swizzling machines. But that is also broken without
the pwrite patches, so likely a different issue (or a problem with the
testcase).

v2: Simplify the patch by dropping the overly clever partial write
logic for swizzled pages.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

drm/i915 wants to read/write more than one page in its fastpath
and hence needs to prefault more than PAGE_SIZE bytes.

Add new functions in filemap.h to make that possible.

Also kill a copy&pasted spurious space in both functions while at it.

v2: As suggested by Andrew Morton, add a multipage parameter to both
functions to avoid the additional branch for the pagemap.c hotpath.
My gcc 4.6 here seems to dtrt and indeed reap these branches where not
needed.

v3: Becaus I couldn't find a way around adding a uaddr += PAGE_SIZE to
the filemap.c hotpaths (that the compiler couldn't remove again),
let's go with separate new functions for the multipage use-case.

v4: Adjust comment to CodingStlye and fix spelling.
Acked-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

While moving around things, this two functions slowly grew out of any
sane bounds. So extract a few lines that do the copying and
clflushing. Also add a few comments to explain what's going on.

v2: Again do s/needs_clflush/needs_clflush_after/ in the write paths
as suggested by Chris Wilson.
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's around 20% faster.
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's too expensive to move it around just for that pwrite, especially
when we're trashing on the mappable gtt part like crazy.
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In micro-benchmarking of the usual pwrite use-pattern of alternating
pwrites with gtt domain reads from the gpu, this yields around 30%
improvement of pwrite throughput across all buffers size. The trick is
that we can avoid clflush cachelines that we will overwrite completely
anyway.

Furthermore for partial pwrites it gives a proportional speedup on top
of the 30% percent because we only clflush back the part of the buffer
we're actually writing.

v2: Simplify the clflush-before-write logic, as suggested by Chris
Wilson.

v3: Finishing touches suggested by Chris Wilson:
- add comment to needs_clflush_before and only set this if the bo is
  uncached.
- s/needs_clflush/needs_clflush_after/ in the write paths to clearly
  differentiate it from needs_clflush_before.
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The pagemap.h prefault helpers do the prefaulting by simply writing
some data into every page. Hence we should not prefault when we're not
yet commited to to actually writing data to userspace. The problem is
now that
- we can't prefault while holding dev->struct_mutex for we could
  deadlock with our own pagefault handler
- we need to grab dev->struct_mutex before copying to sync up with any
  outsanding gpu writes.

Therefore only prefault when we're dropping the lock the first time in
the pread slowpath - at that point we're committed to the write, don't
wait on the gpu anymore and hence won't return early (with e.g.
-EINTR).
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the proper prefault, it's extremely unlikely that we fall back
to the gtt slowpath.

So just kill it and use the shmem_pwrite path as fallback.

To further clean up the code, move the preparatory gem calls into the
respective pwrite functions. This way the gtt_fast->shmem fallback
is much more obvious.
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This speeds up pwrite and pread from ~120 µs ro ~100 µs for
reading/writing 1mb on my snb (if the backing storage pages
are already pinned, of course).

v2: Chris Wilson pointed out a glaring page reference bug - I've
unconditionally dropped the reference. With that fixed (and the
associated reduction of dirt in dmesg) it's now even a notch faster.

v3: Unconditionaly grab a page reference when dropping
dev->struct_mutex to simplify the code-flow.
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

~120 µs instead fo ~210 µs to write 1mb on my snb. I like this.
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No longer needed.
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>