remove redundant structures and unused macros
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These definitions are no longer used after previous cleanups.
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The radio_on variable is defined but never used.
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

replace them with NL80211_AUTHTYPE_ macros
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

replace them with NL80211_IFTYPE_ macros

Also remove redundant functions mwifiex_drv_get_mode()
and mwifiex_bss_ioctl_mode().
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We already tell mac80211 to stop the queue when we hit a certain
threshold. Hence, it shouldn't happen at all that a frame gets queued
for tx on a full queue. Add an error message for this case.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some clients seem to rely upon the reception of BlockAckReqs to flush
their rx reorder buffer. In order to fix aggregation for these clients
rt2x00 should send a BlockAckReq if the transmission of an AMPDU
subframe fails.

Introduce a new flag TXDONE_AMPDU to indicate that this is an AMPDU
subframe and pass IEEE80211_TX_STAT_AMPDU_NO_BACK to mac80211 if an
AMPDU subframe failed during transmission.

This fixes aggregation problems with Intel 5100 Windows STAs (and maybe
others as well).
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add new USB ID
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For STBC transmissions rt2x00 used the number of RxSTBC streams the
destination STA indicates in its HT capabilities as STBC value in
the TXWI.

However, the legacy drivers and our own comment in rt2800.h suggest
that the STBC field in the TXWI only allows a value of 0 or 1.
The values 2 and 3 are reserved (probably for future devices).

And indeed, STBC transmissions to STAs indicating more then 1
RxSTBC stream fail when the STBC field is set to something >1.

Fix this by only setting the STBC field to 1 when STBC should be
used.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2800 devices should adjust their tx power in accordance with the
eeproms temperature calibration values. Add a new driver callback
gain_calibration that is called every 4 seconds.

The rt2800 gain calibration routine simply runs the tx power
configuration that takes care of calculating the temperature
compensation delta.

We don't need to synchronize the calls to rt2800_config_txpower
as they should all happen from mac80211's single threaded workqueue.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since commit d1c3a37c ("mac80211:
clarify alignment docs, fix up alignment") removed the requirement
for a 4-byte aligned payload rt2x00queue_align_payload is obsolete
as mac80211 will align the payload when it passes the frame to the
net stack.

As a result we can remove the call to rt2x00queue_align_payload in the
rx path and since that's the last user we can remove
rt2x00queue_align_payload altogether.

One advantage is that we save some alignment operations for frames
that don't need to be aligned (for example beause they are not passed
to the net stack).
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the indention in rt2800_compesate_txpower and also fix a typo in
the function name rt2800_compesate_txpower -> rt2800_compensate_txpower.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously the HT40 tx power compensation value was calculated for each
rate. However, the calculation is independent of the tx rate and as such
can be precalculated and just passed in for each rate.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the HT40 check inside the calculation function to make it easier
for a later cleanup.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can simply check if the driver registered the watchdog callback.
There's no need to have an additional flag for that.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of hardcoding the tx status fifo size as 512 calculate it based
on the number of tx queues and the number of entries per queue. Also
round the size up to a power of 2 as kfifo would otherwise round it
down.

On rt2800pci this will increase the kfifo size from 512 bytes to 1024
bytes which is then able to hold the tx status for all entries in all
tx queues.

Furthermore, if the number of tx queues or tx entries changes in the
future (use of the MGMT queue for example) the kfifo size doesn't need
to be updated.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of reporting an unlimited number of tx status reports to
mac80211 stop after 16 frames and reschedule the tx status tasklet.
This allows other tasklets to be run inbetween.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of receiving an unlimited number of frames, stop after 16
entries and reschedule the rxdone tasklet. This allows other tasklets
to be run inbetween.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove some unused variables and correct spelling errors.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hw_dot_11n_dev_cap reported by firmware hw_spec
has different format than the 11n capabilities.
Hence a lot of SET_ and RESET_ bit operation macros
were used to convert the dev_cap format to 11n
capability format. However the locally defined 11n
ht_cap macros are not necessary as we can use
IEEE80211_HT_CAP_ macros directly.

The 32-bit dev_cap bitmap is added as comment to
explain the mapping between firmware and 11n spec.

Some unused macros and unnecessary adapter variables
are also removed.
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

and SHORT_SLOT_TIME_ENABLED.
Use WLAN_CAPABILITY_SHORT_SLOT_TIME instead.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mwifiex_set_encrypt_mode()
mwifiex_set_auth_mode()
mwifiex_set_auth()
These functions are confusing and misleading.
And they are really not needed at all.

Some unused definitions are also removed.
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'iw list' is sufficient to retrieve the information which
was displayed by these functions.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This function is nowhere used.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This does not seems to be used anywhere so remove it.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It has the same purpose (and value) as ah->config.max_txtrig_level
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not used anywhere
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Similar to the number of tx queue, the number of keycache entries depends
on the chip and shouldn't be messed with based on EEPROM data.
Remove this field and stick to using AR_KEYTABLE_SIZE
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not used anywhere and seems pointless
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is only used in one place, and the device id check that it's based on
can be moved there as well.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The EEPROM contains a field that can restrict the number of hardware queues,
however this is not only useless (all the known chips contain the same
number of hardware queues), but also potentially dangerous in case of a
misprogrammed EEPROM (could trigger driver crashes), so let's just ignore
it completely.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RF_BANK_SETUP, REG_WRITE_RF_ARRAY and REG_WRITE_ARRAY are way too big,
so they shouldn't be inlined at every single callsite, especially since they
can easily be turned into real functions.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's easier to read and it slightly decreases code size
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reduces the number of calls to register ops. On MIPS this reduces the
ath9k_hw binary size from 321k down to 310k
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With this change, loading the address to a register read/write function
costs only one pointer dereference instead of two. On MIPS this reduces
ath9k_hw binary size from 326k down to 321k.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for using RSN IBSS with ath9k. For now, this uses software
crypto for group addressed frames in RSN IBSS, but that may be
optimized in the future by extending the key cache design to support
per-STA RX GTK.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Stuck beacon detection is supposed to trigger when 9 consecutive beacons
could not be sent by the hardware. When the driver runs only one active
AP mode interface, it still configures the hardware beacon timer for
4 (ATH_BCBUF) beacon slots slots, which causes stuck beacon detection
to be reset if ath9k_hw_stoptxdma clears the stuck frames between
SWBA intervals.
Fix this by not resetting the missed beacon count for empty slots and
multiplying the threshold not by the maximum number of beacon slots
but by the configured number of beacon interfaces.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Single missed (i.e. not transmitted) beacons in AP mode are not very rare
and not necessarily an indicator of strong interference, so only trigger
noise floor recalibration when multiple consecutive beacons could not
be transmitted.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AP mode beacon timers in ath9k are configured in milliseconds, which breaks
when increasing ATH_BCBUF to 8 instead of 4 (due to rounding errors).
Since the hardware timers are actually configured in microseconds, it's
better to let the driver use that unit directly.

To be able to do that, the beacon interval parameter abuse for passing
certain flags needs to be removed. This is easy to do, because those flags
are completely unnecessary anyway. ATH9K_BEACON_ENA is ignored,
ATH9K_BEACON_RESET_TSF can be replaced with calling ath9k_hw_reset_tsf
from the driver directly.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>