Implement clock support for Tegra124.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>

The Tegra30 clock bindings lack few IDs for audio and clk_out muxes.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>

These clocks were named gr2d and gr3d on Tegra20 and Tegra30, so use the
same names on Tegra114 for consistency.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>

commit 992bb598 forgot to move dfll_soc and
dfll_ref to include/dt-bindings/clock/tegra114-car.h. Add them again in this
patch as TEGRA114_CLK_DFLL_SOC and TEGRA114_CLK_DFLL_REF.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>

This patch adds support for the clocks provided by the Clock Management
Unit of Energy Micro's efm32 Giant Gecko SoCs including device tree
bindings.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The ams AS3722 is a compact system PMU suitable for mobile phones,
tablets etc. It has 4 DC/DC step-down regulators, 3 DC/DC step-down
controller, 11 LDOs, RTC, automatic battery, temperature and
over-current monitoring, 8 GPIOs, ADC and a watchdog.

Add MFD core driver for the AS3722 to support core functionality.
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NFlorian Lobmaier <florian.lobmaier@ams.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The wake-up interrupt bit is available on omap3/4/5 processors
unlike what we claim. Without fixing it we cannot use it on
omap3 and the system configured for wake-up events will just
hang on wake-up.

Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Fix AT91_PINCTRL_DEBOUNCE_VAL dt macro typo.
Fix at91_pinctrl_mux_ops callback typos.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The platform which it pertains to is no longer supported and is actually
causing some confusion in the new common clock implementation. A recent
patch removed its use in the clock driver, let's take out the definitions
too.
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

These are required to request DBx500 PRCMU clocks from Device Tree. The
numbers used are taken directly from the Hardware Specification document.
We're moving them from the DBx500 PRCMU include file into the DT include
directory and referencing them from the former via a #include.
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Define a PWM_POLARITY_INVERTED macro in include/dt-bindings/pwm/pwm.h to
be used by device tree sources.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NThierry Reding <thierry.reding@gmail.com>

Many of Key device tree bindings uses the constant number as key code
which matches with kernel header key code and then comment as follows
for reference/better readability:
	linux,code = <102>; /* KEY_HOME */

Create a DT header which defines all the key code so that DT key bindings
can use it as follows:
	linux,code = <KEY_HOME>;
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

Move imx-audmux macro definitions to include/dt-bindings, so they can be
used for devicetree.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds pinctrl device tree settings for uart0 and uart2
for ccu8540 board.
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds new, Common Clock Framework-based clock driver for Samsung
S3C64xx SoCs. The driver is just added, without actually letting the
platforms use it yet, since this requires more intermediate steps.
Signed-off-by: NTomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Using #include <include/...> is a bit odd. It happens to work because the DTC
flags include -Iarch/FOO/boot/dts as well as arch/FOO/boot/dts/include and
arch/FOO/boot/dts/include/dt-bindings is a symlink to include/dt-bindings.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The fec/enet driver calculates MDC rate with the formula below.

  ref_freq / ((MII_SPEED + 1) x 2)

The ref_freq here is the fec internal module clock, which is missing
from clk-vf610 clock driver right now.  And clk-vf610 driver mistakenly
supplies RMII clock (50 MHz) as the source to fec.  This results in the
situation that fec driver gets ref_freq as 50 MHz, while physically it
runs at 66 MHz (fec module clock physically sources from ipg which runs
at 66 MHz).  That's why software expects MDC runs at 2.5 MHz, while the
measurement tells it runs at 3.3 MHz.  And this causes the PHY KSZ8041
keeps swithing between Full and Half mode as below.

  libphy: 400d0000.etherne:00 - Link is Up - 100/Full
  libphy: 400d0000.etherne:00 - Link is Up - 100/Half
  libphy: 400d0000.etherne:00 - Link is Up - 100/Full
  libphy: 400d0000.etherne:00 - Link is Up - 100/Half
  libphy: 400d0000.etherne:00 - Link is Up - 100/Full
  libphy: 400d0000.etherne:00 - Link is Up - 100/Half

Add the missing module clock for ENET0 and ENET1, and correct the clock
supplying in device tree to fix above issue.

Thanks to Alison Wang <b18965@freescale.com> for debugging the issue.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

DMA-cell content is a concatenation of several values. In order to keep this
stuff human readable, macros are introduced.

The values for the FIFO configuration are not the same as the ones used in the
configuration register in order to keep backward compatibility. Most devices
use the half FIFO configuration but USART ones have to use the ASAP
configuration. This parameter was not initially planed to be into the at91 dma
dt binding. The third cell will be used to store this parameter, it will
become a concatenation of the FIFO configuration and of the peripheral ID. In
order to keep backward compatibility i.e. FIFO configuration is equal to 0, we
have to perform a translation since the value to put in the register to set
half FIFO is 1.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Pinctrl headers were not protected with #ifndef.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The pinctrl IP inside the AM33XX family differs slightly from
what is found on OMAP2+. Define a specific header to take account
of the differences.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Most of the constants are taken from arch/arm/mach-omap2/mux.h.
Define some others for the PIN_OUTPUT_* flavours.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Audio subsystem is introduced in s5pv210 and exynos platforms.
This has seperate clock controller which can control i2s0 and
pcm0 clocks. This patch registers the audio subsystem clocks
with the common clock framework on Exynos family.
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add clock support for Vybrid VF610. It uses dtc macro support to
define all clock IDs in vf610-clock.h to keep clock IDs coherence
between kernel and DT.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add clock support for i.MX6 SoloLite.  It uses the dtc marco support to
define all clock IDs in imx6sl-clock.h, which will be included by both
clock driver and device tree sources, so that the data will stay sync
all the time between kernel and DT.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This driver adds support the Cortex-A9 based SoCs from Rockchip,
so at least the RK2928, RK3066 (a and b) and RK3188.
Earlier Rockchip SoCs seem to use similar mechanics for gpio
handling so should be supportable with relative small changes.
Pull handling on the rk3188 is currently a stub, due to it being
a bit different to the earlier SoCs.

Pinmuxing as well as gpio (and interrupt-) handling tested on
a rk3066a based machine.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

DMA-cell content is a concatenation of several values. In order to keep this
stuff human readable, macros are introduced.

The values for the FIFO configuration are not the same as the ones used in the
configuration register in order to keep backward compatibility. Most devices
use the half FIFO configuration but USART ones have to use the ASAP
configuration. This parameter was not initially planed to be into the at91 dma
dt binding. The third cell will be used to store this parameter, it will
become a concatenation of the FIFO configuration and of the peripheral ID. In
order to keep backward compatibility i.e. FIFO configuration is equal to 0, we
have to perform a translation since the value to put in the register to set
half FIFO is 1.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

All Tegra GPIOs are named after the GPIO bank and GPIO number within
the bank. Define a macro to calculate the GPIO ID based on those
parameters. Make the macro available via all Tegra .dtsip files.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Create a header file to define the clock IDs used by the Tegra114 clock
binding. Remove the list of definitions from the binding documentation,
and refer the reader to the header file.

This will allow the same header to be used by both device tree files,
and drivers implementing this binding, which guarantees that the two
stay in sync. This also makes device trees more readable by using names
instead of magic numbers.
Signed-off-by: NHiroshi Doyu <hdoyu@nvidia.com>
[swarren, add header to clock/ instead of clk/ to match binding location]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Create a header file to define the clock IDs used by the Tegra30 clock
binding. Remove the list of definitions from the binding documentation,
and refer the reader to the header file.

This will allow the same header to be used by both device tree files,
and drivers implementing this binding, which guarantees that the two
stay in sync. This also makes device trees more readable by using names
instead of magic numbers.
Signed-off-by: NHiroshi Doyu <hdoyu@nvidia.com>
[swarren, add header to clock/ instead of clk/ to match binding location]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Create a header file to define the clock IDs used by the Tegra20 clock
binding. Remove the list of definitions from the binding documentation,
and refer the reader to the header file.

This will allow the same header to be used by both device tree files,
and drivers implementing this binding, which guarantees that the two
stay in sync. This also makes device trees more readable by using names
instead of magic numbers.
Signed-off-by: NHiroshi Doyu <hdoyu@nvidia.com>
[swarren, add header to clock/ instead of clk/ to match binding location]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The ARM GIC binding defines a few custom cells and flags for its IRQ
specifier. Provide names for those.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>

Many IRQ device tree bindings use the same flags. Create a header to
define those.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>

Many GPIO device tree bindings use the same flags. Create a header to
define those.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>