Newer firmware understands the concept of a trusted VF, so propagate the
trusted VF attribute set by the PF admin. to the firmware.  Also, check
the firmware trusted setting when considering the VF MAC address change
and reporting the trusted setting to the user.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for BCM957504 with device ID 1751
Signed-off-by: NErik Burrows <erik.burrows@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware error recover is the major change in this spec.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit b639583f.

As per discussion with Jakub Kicinski and Michal Kubecek,
this will be better addressed by soon-too-come ethtool netlink
API with additional indication that given configuration request
is supposed to be persisted.

Also, remove the parameter support from bnxt_en driver.

Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Michal Kubecek <mkubecek@suse.cz>
Suggested-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, user can do dump or get of param values right after the
devlink params are registered. However the driver may not be initialized
which is an issue. The same problem happens during notification
upon param registration. Allow driver to publish devlink params
whenever it is ready to handle get() ops. Note that this cannot
be resolved by init reordering, as the "driverinit" params have
to be available before the driver is initialized (it needs the param
values there).
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BNXT only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get(). The conversion is
straight forward here since the PF and VF code use the same getter.

Since bnxt makes uses of switchdev_port_same_parent_id() convert it to
use netdev_port_same_parent_id().
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates drivers to use the new flow action infrastructure.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides the flow_stats structure that acts as container for
tc_cls_flower_offload, then we can use to restore the statistics on the
existing TC actions. Hence, tcf_exts_stats_update() is not used from
drivers anymore.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch wraps the dissector key and mask - that flower uses to
represent the matching side - around the flow_match structure.

To avoid a follow up patch that would edit the same LoCs in the drivers,
this patch also wraps this new flow match structure around the flow rule
object. This new structure will also contain the flow actions in follow
up patches.

This introduces two new interfaces:

	bool flow_rule_match_key(rule, dissector_id)

that returns true if a given matching key is set on, and:

	flow_rule_match_XYZ(rule, &match);

To fetch the matching side XYZ into the match container structure, to
retrieve the key and the mask with one single call.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When calling firmware to allocate a CP ring or NQ, an interrupt associated
with that ring may be generated immediately before the doorbell is even
setup after the firmware call returns.  When servicing the interrupt, the
driver may crash when trying to access the doorbell.

Fix it by disabling interrupt on that vector until the doorbell is
set up.

Fixes: 697197e5 ("bnxt_en: Re-structure doorbells.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register devlink_port with devlink and create initial port params
table for bnxt_en. The table consists of a generic parameter:

wake_on_lan: Enables Wake on Lan for this port when magic packet
is received with this port's MAC address using ACPI pattern.
If enabled, the controller asserts a wake pin upon reception of
WoL packet.  ACPI (Advanced Configuration and Power Interface) is
an industry specification for the efficient handling of power
consumption in desktop and mobile computers.

v2->v3:
- Modify bnxt_dl_wol_validate(), to throw error message when user gives
  value other than DEVLINK_PARAM_WAKE_MAGIC ot to disable WOL.
- Use netdev_err() instead of netdev_warn(), when devlink_port_register()
  and devlink_port_params_register() returns error. Also, don't log rc
  in this message.

Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When allocating memory pages for context memory, if the last page table
should be fully populated, the current code will set nr_pages to 0 when
calling bnxt_alloc_ctx_mem_blk().  This will cause the last page table
to be completely blank and causing some RDMA failures.

Fix it by setting the last page table's nr_pages to the remainder only
if it is non-zero.

Fixes: 08fe9d18 ("bnxt_en: Add Level 2 context memory paging support.")
Reported-by: NEric Davis <eric.davis@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnxt_hwrm_check_pf_rings(), add the proper flag to test the NQ
resources.  Without the proper flag, the firmware will change
the NQ resource allocation and remap the IRQ, causing missing
IRQs.  This issue shows up when adding MQPRIO TX queues, for example.

Fixes: 36d65be9 ("bnxt_en: Disable MSIX before re-reserving NQs/CMPL rings.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.

This change was generated with the following Coccinelle SmPL patch:

@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@

-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLuis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: NChristoph Hellwig <hch@lst.de>

For a little better performance on faster machines and faster link
speeds.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Older firmware only supports 16-bit flow handle, because of which the
number of flows that can be offloaded can’t scale beyond a point.
Newer firmware supports 64-bit flow handle enabling the host to scale
upto millions of flows. With the new 64-bit flow handle support, driver
has to query flow stats in a different way compared to the older approach.

This patch adds support for 64-bit flow handle and new way to query
flow stats.
Signed-off-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If RDMA is supported on the 57500 chip, increase context memory
allocations for the resources used by RDMA.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the new functions bnxt_alloc_ctx_pg_tbls()/bnxt_free_ctx_pg_tbls()
to allocate and free pages for context memory.  The new functions
will handle the different levels of paging support and allocate/free
the pages accordingly using the existing functions.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support level 2 context page memory structures, enhance the
bnxt_ring_mem_info structure with a "depth" field to specify the page
level and add a flag to specify using full pages for L1 and L2 page
tables.  This is needed to support RDMA functionality on 57500 chips
since RDMA requires more context memory.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Earlier, some of the firmware commands (ex: CFA_FLOW_*) which are processed
by KONG processor were sent to the CHIMP processor from the host. This
approach was taken as there was no direct message channel to KONG.
CHIMP in turn used to send them to KONG. Newer firmware supports a new
message channel which the host can send messages directly to the KONG
processor.

This patch adds support for required changes needed in the driver
to support direct KONG message channel.  This speeds up flow related
messages sent to the firmware for CLS_FLOWER offload.
Signed-off-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These routines will be enhanced in the subsequent patch to
return the 2nd firmware comm. channel's hwrm response address &
sequence id respectively.
Signed-off-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Typecast hwrm_cmd_resp_addr to (u8 *) from (void *) before doing
arithmetic.
Signed-off-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for adding a 2nd communication channel to firmware.
Signed-off-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set hwrm_intr_seq_id value to its inverted value instead of
HWRM_SEQ_INVALID, when an hwrm completion of type
CMPL_BASE_TYPE_HWRM_DONE is received. This will enable us to use
the complete 16-bit sequence ID space.
Signed-off-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The major changes are in the flow offload firmware APIs.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code has 2 problems.  It assumes that the RX ring for
the loopback packet is combined with the TX ring.  This is not
true if the ethtool channels are set to non-combined mode.  The
second problem is that it won't work on 57500 chips without
adjusting the logic to get the proper completion ring (cpr) pointer.
Fix both issues by locating the proper cpr pointer through the RX
ring.

Fixes: e44758b7 ("bnxt_en: Use bnxt_cp_ring_info struct pointer as parameter for RX path.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With autoneg enabled, PHY loopback test fails. To disable autoneg,
driver needs to send a valid forced speed to FW. FW is not sending
async event for invalid speeds. To fix this, query forced speeds
and send the correct speed when disabling autoneg mode.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Port statistics which include RDMA counters are useful even when the
netdevice is down.  Do not free the port statistics DMA buffers
when the netdevice is down.  This is keep the snapshot of the port
statistics and counters will just continue counting when the
netdevice goes back up.

Split the bnxt_free_stats() function into 2 functions.  The port
statistics buffers will only be freed when the netdevice is
removed.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the current driver, the statistics reported by .ndo_get_stats64()
are reset when the device goes down.  Store a snapshot of the
rtnl_link_stats64 before shutdown.  This snapshot is added to the
current counters in .ndo_get_stats64() so that the counters will not
get reset when the device is down.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently firmware specific errors are returned directly in flash_device
and reset ethtool hooks. Modify it to return linux standard errors
to userspace when flashing operations fail.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the code allows ETS bandwidth weight 0 to be set on unused TCs.
We should not set any DCB parameters on unused TCs at all.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Display the CoS counters as additional priority counters by looking up
the priority to CoS queue mapping.  If the TX extended port statistics
block size returned by firmware is big enough to cover the CoS counters,
then we will display the new priority counters.  We call firmware to get
the up-to-date pri2cos mapping to convert the CoS counters to
priority counters.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are some minor differences when assigning VF resources on the
new chips.  The MSIX (NQ) resource has to be assigned and ring group
is not needed on the new chips.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When bringing up a device, the code checks to see if the number of
MSIX has changed.  pci_disable_msix() should be called first before
changing the number of reserved NQs/CMPL rings.  This ensures that
the MSIX vectors associated with the NQs/CMPL rings are still
properly mapped when pci_disable_msix() masks the vectors.

This patch will prevent errors when RDMA support is added for the new
57500 chips.  When the RDMA driver shuts down, the number of NQs is
decreased and we must use the new sequence to prevent MSIX errors.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnxt_en requires same number of stat_ctxs as CP rings but RDMA
requires only 1 stat_ctx.  Also add a new parameter resv_stat_ctxs
to better keep track of stat_ctxs reserved including resources used
by RDMA.  Add a stat_ctxs parameter to all the relevant resource
reservation functions so we can reserve the correct number of
stat_ctxs.

Prior to this patch, we were not reserving the extra stat_ctx for
RDMA and RDMA would not work on the new 57500 chips.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling bnxt_set_max_func_stat_ctxs() to modify max stat_ctxs requested
or freed by the RDMA driver is wrong. After introducing reservation of
resources recently, the driver has to keep track of all stat_ctxs
including the ones used by the RDMA driver.  This will provide a better
foundation for accurate accounting of the stat_ctxs.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For bnxt_en driver, stat_ctxs created will always be same as
cp_nr_rings. Remove extra variable that duplicates the value.
Also introduce bnxt_get_avail_stat_ctxs_for_en() helper to get
available stat_ctxs and bnxt_get_ulp_stat_ctxs() helper to return
number of stat_ctxs used by RDMA.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The available CP rings are calculated differently on the new 57500
chips, so add this helper to do this calculation correctly.  The
VFs will be assigned these available CP rings.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PF has a pool of NQs and MSIX vectors assigned to it based on
NVRAM configurations.  The number of usable MSIX vectors on the PF
is the minimum of the NQs and MSIX vectors.  Any excess NQs without
associated MSIX may be used for the VFs, so we need to store this
max_nqs value.  max_nqs minus the NQs used by the PF will be the
available NQs for the VFs.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers may not be able to implement a VLAN addition or reconfiguration.
In those cases it's desirable to explain to the user that it was
rejected (and why).

To that end, add extack argument to ndo_bridge_setlink. Adapt all users
to that change.

Following patches will use the new argument in the bridge driver.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>