When the device mac address is changed, we must deregister the vxlan
steering rule associated with the previous mac, and register a new
steering rule using the new mac.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the value used to dump the vxlan offloads device capability to align
with the MLX4_DEV_CAP_FLAG2_yyy definition. While on that, add dump to
the IPoIB flow-steering device capability and fix small typo.

The vxlan cap value wasn't fully handled when a conflict was resolved
between MLX4_DEV_CAP_FLAG2_DMFS_IPOIB coming from the IB tree to
MLX4_DEV_CAP_FLAG2_VXLAN_OFFLOADS coming from net-next.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tx descriptor version of RTL8111B belong to RTL_TD_0.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to fix the compatibility to the STiD127 SoC.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to fix the chain mode that was broken
and generated a panic. This patch reviews the chain/ring
modes now shaing the same structure and taking care
about the pointers and callbacks.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to fix and tune the default buffer sizes.
It reduces the default bufsize used by the driver from
4KiB to 1536 bytes.

Patch has been tested on both ARM and SH4 platform based.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to disable the EEE (so HW and timers)
for example when the phy communicates that the EEE
can be supported anymore.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

udelay() does not work on some architectures for values above
2000, in particular on ARM:

ERROR: "__bad_udelay" [drivers/net/ethernet/brocade/bna/bna.ko] undefined!
Reported-by: NVagrant Cascadian <vagrant@debian.org>
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pci shutdown handler added in:

    bnx2: Add pci shutdown handler
    commit 25bfb1dd

created a shutdown down sequence without chip reset if the device was
never brought up.  This can cause the firmware to shutdown the PHY
prematurely and cause MMIO read cycles to be unresponsive.  On some
systems, it may generate NMI in the bnx2's pci shutdown handler.

The fix is to tell the firmware not to shutdown the PHY if there was
no prior chip reset.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the PF call to pci_enable_sriov from the PF probe function
stalls for 10 seconds times the number of VFs probed on the host. This
happens because the way for such VFs to determine of the PF
initialization finished, is by attempting to issue reset on the
comm-channel and get timeout (after 10s).

The PF probe function is called from a kenernel workqueue, and therefore
during that time, rcu lock is being held and kernel's workqueue is
stalled. This blocks other processes that try to use the workqueue
or rcu lock.  For example, interface renaming which is calling
rcu_synchronize is blocked, and timedout by systemd.

Changed mlx4_init_slave() to allow VF probed on the host to immediatly
detect that the PF is not ready, and return EPROBE_DEFER instantly.

Only when the PF finishes the initialization, allow such VFs to
access the comm channel.

This issue and fix are relevant only for probed VFs on the hypervisor,
there is no way to pass this information to a VM until comm channel is
ready, so in a VM, if PF is not ready, the first command will be timedout
after 10 seconds and return EPROBE_DEFER.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a regression introduced by [1]. outbox was accessed instead of
outbox->buf. Typo was copy-pasted to [2] and [3].

[1] - cc1ade94 mlx4_core: Disable memory windows for virtual functions
[2] - 4de65803 mlx4_core: Add support for steerable IB UD QPs
[3] - 7ffdf726 net/mlx4_core: Add basic support for TCP/IP offloads under
      tunneling
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code to load a MAC address into a u64 for passing to the
hypervisor via a register is broken on little endian.

Create a helper function called ibmveth_encode_mac_addr
which does the right thing in both big and little endian.

We were storing the MAC address in a long in struct ibmveth_adapter.
It's never used so remove it - we don't need another place in the
driver where we create endian issues with MAC addresses.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When allocating RX buffers a fixed size is used, while freeing is based
on actually received bytes, resulting in the following kernel warning
when CONFIG_DMA_API_DEBUG is enabled:
 WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1051 check_unmap+0x258/0x894()
 macb e000b000.ethernet: DMA-API: device driver frees DMA memory with different size [device address=0x000000002d170040] [map size=1536 bytes] [unmap size=60 bytes]
 Modules linked in:
 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.0-rc3-xilinx-00220-g49f84081ce4f #65
 [<c001516c>] (unwind_backtrace) from [<c0011df8>] (show_stack+0x10/0x14)
 [<c0011df8>] (show_stack) from [<c03c775c>] (dump_stack+0x7c/0xc8)
 [<c03c775c>] (dump_stack) from [<c00245cc>] (warn_slowpath_common+0x60/0x84)
 [<c00245cc>] (warn_slowpath_common) from [<c0024670>] (warn_slowpath_fmt+0x2c/0x3c)
 [<c0024670>] (warn_slowpath_fmt) from [<c0227d44>] (check_unmap+0x258/0x894)
 [<c0227d44>] (check_unmap) from [<c0228588>] (debug_dma_unmap_page+0x64/0x70)
 [<c0228588>] (debug_dma_unmap_page) from [<c02ab78c>] (gem_rx+0x118/0x170)
 [<c02ab78c>] (gem_rx) from [<c02ac4d4>] (macb_poll+0x24/0x94)
 [<c02ac4d4>] (macb_poll) from [<c031222c>] (net_rx_action+0x6c/0x188)
 [<c031222c>] (net_rx_action) from [<c0028a28>] (__do_softirq+0x108/0x280)
 [<c0028a28>] (__do_softirq) from [<c0028e8c>] (irq_exit+0x84/0xf8)
 [<c0028e8c>] (irq_exit) from [<c000f360>] (handle_IRQ+0x68/0x8c)
 [<c000f360>] (handle_IRQ) from [<c0008528>] (gic_handle_irq+0x3c/0x60)
 [<c0008528>] (gic_handle_irq) from [<c0012904>] (__irq_svc+0x44/0x78)
 Exception stack(0xc056df20 to 0xc056df68)
 df20: 00000001 c0577430 00000000 c0577430 04ce8e0d 00000002 edfce238 00000000
 df40: 04e20f78 00000002 c05981f4 00000000 00000008 c056df68 c0064008 c02d7658
 df60: 20000013 ffffffff
 [<c0012904>] (__irq_svc) from [<c02d7658>] (cpuidle_enter_state+0x54/0xf8)
 [<c02d7658>] (cpuidle_enter_state) from [<c02d77dc>] (cpuidle_idle_call+0xe0/0x138)
 [<c02d77dc>] (cpuidle_idle_call) from [<c000f660>] (arch_cpu_idle+0x8/0x3c)
 [<c000f660>] (arch_cpu_idle) from [<c006bec4>] (cpu_startup_entry+0xbc/0x124)
 [<c006bec4>] (cpu_startup_entry) from [<c053daec>] (start_kernel+0x350/0x3b0)
 ---[ end trace d5fdc38641bd3a11 ]---
 Mapped at:
  [<c0227184>] debug_dma_map_page+0x48/0x11c
  [<c02ab32c>] gem_rx_refill+0x154/0x1f8
  [<c02ac7b4>] macb_open+0x270/0x3e0
  [<c03152e0>] __dev_open+0x7c/0xfc
  [<c031554c>] __dev_change_flags+0x8c/0x140

Fixing this by passing the same size which is passed during mapping the
memory to the unmap function as well.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With CONFIG_DMA_API_DEBUG enabled the following warning is printed:
 WARNING: CPU: 0 PID: 619 at lib/dma-debug.c:1101 check_unmap+0x758/0x894()
 macb e000b000.ethernet: DMA-API: device driver failed to check map error[device address=0x000000002d171c02] [size=322 bytes] [mapped as single]
 Modules linked in:
 CPU: 0 PID: 619 Comm: udhcpc Not tainted 3.14.0-rc3-xilinx-00219-gd158fc7f #63
 [<c001516c>] (unwind_backtrace) from [<c0011df8>] (show_stack+0x10/0x14)
 [<c0011df8>] (show_stack) from [<c03c7714>] (dump_stack+0x7c/0xc8)
 [<c03c7714>] (dump_stack) from [<c00245cc>] (warn_slowpath_common+0x60/0x84)
 [<c00245cc>] (warn_slowpath_common) from [<c0024670>] (warn_slowpath_fmt+0x2c/0x3c)
 [<c0024670>] (warn_slowpath_fmt) from [<c0228244>] (check_unmap+0x758/0x894)
 [<c0228244>] (check_unmap) from [<c0228588>] (debug_dma_unmap_page+0x64/0x70)
 [<c0228588>] (debug_dma_unmap_page) from [<c02aba64>] (macb_interrupt+0x1f8/0x2dc)
 [<c02aba64>] (macb_interrupt) from [<c006c6e4>] (handle_irq_event_percpu+0x2c/0x178)
 [<c006c6e4>] (handle_irq_event_percpu) from [<c006c86c>] (handle_irq_event+0x3c/0x5c)
 [<c006c86c>] (handle_irq_event) from [<c006f548>] (handle_fasteoi_irq+0xb8/0x100)
 [<c006f548>] (handle_fasteoi_irq) from [<c006c148>] (generic_handle_irq+0x20/0x30)
 [<c006c148>] (generic_handle_irq) from [<c000f35c>] (handle_IRQ+0x64/0x8c)
 [<c000f35c>] (handle_IRQ) from [<c0008528>] (gic_handle_irq+0x3c/0x60)
 [<c0008528>] (gic_handle_irq) from [<c0012904>] (__irq_svc+0x44/0x78)
 Exception stack(0xed197f60 to 0xed197fa8)
 7f60: 00000134 60000013 bd94362e bd94362e be96b37c 00000014 fffffd72 00000122
 7f80: c000ebe4 ed196000 00000000 00000011 c032c0d8 ed197fa8 c0064008 c000ea20
 7fa0: 60000013 ffffffff
 [<c0012904>] (__irq_svc) from [<c000ea20>] (ret_fast_syscall+0x0/0x48)
 ---[ end trace 478f921d0d542d1e ]---
 Mapped at:
  [<c0227184>] debug_dma_map_page+0x48/0x11c
  [<c02aaca0>] macb_start_xmit+0x184/0x2a8
  [<c03143c0>] dev_hard_start_xmit+0x334/0x470
  [<c032c09c>] sch_direct_xmit+0x78/0x2f8
  [<c0314814>] __dev_queue_xmit+0x318/0x708

due to missing checks of the dma mapping. Add the appropriate checks to fix
this.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In kexec scenario, we failed to load the mlx4 driver in the
second kernel because the ownership bit was hold by the first
kernel without release correctly.

The patch adds shutdown() interface so that the ownership can
be released correctly in the first kernel. It also helps avoiding
EEH error happened during boot stage of the second kernel because
of undesired traffic, which can't be handled by hardware during
that stage on Power platform.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a CPDMA RX Descriptor leak that occurs after taking
the interface down when the CPSW is in Dual MAC mode. Previously
the CPSW_ALE port was left open up which causes packets to be received
and processed by the RX interrupt handler and were passed to the
non active network interface where they were ignored.

The fix is for the slave_stop function of the selected interface
to disable the respective CPSW_ALE Port from forwarding packets. This
blocks traffic from being received on the inactive interface.
Signed-off-by: NSchuyler Patton <spatton@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of TX workarounds in be_xmit_workarounds() routine
are not applicable (and result in HW errors) to Skyhawk-R chip.
Isolate BE3-R/Lancer specific workarounds to a separate routine.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_padto(), skb_share_check() and __vlan_put_tag() routines free
skb when they return an error. This patch fixes be_xmit_workarounds()
to not free skb again in such cases.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should clear promiscuous bits in adapter->flags while disabling promiscuous
mode. Else we will not put interface back into VLAN promisc mode if the vlans
already added exceeds the maximum limit.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For disabling transparent tagging issue SET_HSW_CONFIG with pvid_valid=1
and pvid=0xFFFF and not with the default pvid as this case would fail in Lancer.
Hence removing the get_hsw_config call from be_vf_setup() as it's
only use of getting default pvid is no longer needed.

Also do proper housekeeping only if the FW command succeeds.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ->tc_cfg[] array has QLC_DCB_MAX_TC (8) elements so the check is
off by one.  These functions are always called with valid values though
so it doesn't affect how the code works.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this patch b44_check_phy() was called when the phy called the
adjust callback. This method only change the mac duplex mode when the
carrier was off. When the phy changed the duplex mode after the carrier
was on the mac was not changed. This happened when an external phy was
used.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When support for external phys was added to b44, the calls to start and
stop the phy were missing in the mac driver. This adds the calls to
phy_start() and phy_stop().
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent commit "fe1624cf bna: RX Filter Enhancements" disables
VLAN tag stripping if the NIC is in promiscuous mode. This causes
__vlan_hwaccel_put_tag() is called when the stripping is disabled.
Because of this VLAN over bna does not work and causes BUGs in conjunction
with openvswitch like this:
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Redefine the RXD_ERR_MASK to include only relevant error bits. This fixes
a customer reported issue of randomly dropping packets on the 5719.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit c14db202 "bnx2x: Correct default Tx switching behaviour" supposedly
changed the default Tx switching behaviour, but was missing the fastpath change
required for FW to pass packets from PFs to VFs.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we receive a PTP event from the NIC when we haven't set up PTP state
in the driver, we attempt to read through a NULL pointer efx->ptp_data,
triggering a panic.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Acked-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without a shutdown handler, T4 cards behave very badly after a kexec.
Some firmware calls return errors indicating allocation failures, for
example. This is probably because thouse resources were not released by
a BYE message to the firmware, for example.

Using the remove handler guarantees we will use a well tested path.

With this patch I applied, I managed to use kexec multiple times and
probe and iSCSI login worked every time.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Driver was not re-setting sds ring count to 1 after failing
   to allocate msi-x interrupts.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o This patch reverts commit 1414abea
  (qlcnic: Restrict VF from configuring any VLAN mode.)
  This will allow same multicast address to be used with any VLAN
  instead of programming seperate (MAC, VLAN) tuples in adapter.
  This will help save some multicast filters.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Once interrupts are enabled, instead of using module parameters,
use flags (QLCNIC_MSI_ENABLED and QLCNIC_MSIX_ENABLED) set by driver
to check interrupt mode.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver was treating -ve return value as success in case of
qlcnic_enable_msi_legacy() failure
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump all Mellanox driver versions.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Boris reports he's seeing:
> [    9.195943] INFO: trying to register non-static key.
> [    9.196031] the code is fine but needs lockdep annotation.
> [    9.196031] turning off the locking correctness validator.
> [    9.196031] CPU: 1 PID: 933 Comm: modprobe Not tainted 3.14.0-rc4+ #1
with the r8169 driver.

These are occuring because the seqcount embedded in u64_stats_sync on
32-bit SMP is uninitialized which is making lockdep unhappy.
Signed-off-by: NKyle McMartin <kyle@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_dma_desc_resources() returns an error value and the next line
actually checks for it, so assign the return value properly.

Found by the coverity scanner.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current flow: Set TX BD ready, and then set "INT" and "PINS" bit to
enable tx interrupt generation and crc checksum.

There has potential issue like as:
CPU			fec uDMA
Set tx ready bit
			uDMA start the BD transmission
Set "INT" bit
Set "PINS" bit
...

Above situation cause fec tx interrupt lost and fec MAC don't do
CRC checksum. The patch fix the potential issue.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Acked-by: NFrank Li <Frank.li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the introduction of the support for Armada 375 and Armada 38x,
the hidden Kconfig option MACH_ARMADA_370_XP is being renamed to
MACH_MVEBU_V7. Therefore, the dependency that was used for the mvneta
driver can no longer work. This commit replaces this dependency by a
dependency on PLAT_ORION, which is used similarly for the mv643xx_eth
driver.

In addition to this, it takes this opportunity to adjust the
description and help text to indicate that the driver can is also used
for Armada 38x. Note that Armada 375 cannot use this driver as it has
a completely different networking unit, which will require a separate
driver.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If napi is left enabled after a failed attempt to bring the interface
up, we BUG:

fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch
libphy: PHY fixed-0:00 not found
fec 2188000.ethernet eth0: could not attach to PHY
------------[ cut here ]------------
kernel BUG at include/linux/netdevice.h:502!
Internal error: Oops - BUG: 0 [#1] SMP ARM
...
PC is at fec_enet_open+0x4d0/0x500
LR is at __dev_open+0xa4/0xfc

Only enable napi after we are past all the failure paths.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).

This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Otherwise the device is not completely shut down.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>