Simplify info callbacks by using the snd_ctl_enum_info() helper function.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Simplify the info callback by using the snd_ctl_enum_info() helper function.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Simplify info callbacks by using the snd_ctl_enum_info() helper function.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Simplify the info callback by using the snd_ctl_enum_info() helper function.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Introduce the helper function snd_ctl_enum_info() to fill out the
elem_info fields for an enumerated control.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add experimental support for the Asus Xonar HDAV1.3 Slim sound card.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add experimental support for the Asus Xonar DG sound card.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add support for the AuzenTech X-Meridian 7.1 2G sound card.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add PCI IDs for some unknown models.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For the CSxxxx and AKxxxx DAC/ADC chips, the MCLK factor in double rate
modes (64-96 kHz) can be reduced to 128x without reducing sound quality.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Replace the get_i2s_mclk callback with tables of MCLK values.  This
simplifies the MCLK-handling code in both the framework and the model-
specific drivers.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Do not apply the headphone gain offset to any but the front DAC.  These
DACs would not be used in headphone mode, so this saves a few register
writes.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Remove the DAC Oversampling mixer control because this setting does not
make much sense.

For cards with the H6 daughterboard, 128x oversampling was disabled
anyway because these high MCLK frequency would not be compatible with
the connector cable.

For cards without the H6 daughterboard, 128x gives a slightly higher
output quality; there is no reason to reduce it to 64x except for saving
power, but then these cards have not been designed to be power efficient
anyway (the D2's blinkenlights cannot be disabled).
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Because of the unshielded connector cable, it is important to use as low
a master clock frequency as possible with the H6.

For double rate modes (64-96 kHz), the MCLK rate is unconditionally
lowered from 512x to 256x because the higher rate would not improve
anything.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The clock output of the CS2000, which is used as master clock for the
DACs, was using half the actual master clock frequency for some reason.
Using the theoretically correct frequency seems also to work in practice.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

On the Xonar Essence ST Deluxe, remove all mixer controls that would
require I2C communication with the third DAC, which does not work
because of an addressing conflict with the CS2000 chip.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Change the PCM format used for the PCM1796 from left-justified to I2S to
ensure that the correct format is used even for the Essence ST Deluxe's
center/LFE DAC, where I2C does not work because of an address conflict
with the CS2000 chip.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The PCM1796 needs the master clock for I2C communication to work, so
add delays after clock changes to ensure that the clock is stable when
we try to write the DACs' registers.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

To make the I2C communication reliable when using the H6 daughterboard,
reduce the I2C clock frequency.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix wrong register bits for SPI clock cycle times longer than 160 ns,
and adjust the polling loop timeout for these speeds.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The number of DACs can now be deduced from the dac_channels_mixer field,
so the private_data field is no longer needed.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For cards like the Xonar HDAV1.3, differentiate between the number of
PCM channels that can be played and the number of channels whose volume
can be adjusted.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

snd_pcm_hw_param_near() will leak the memory allocated to 'save' if the
call to snd_pcm_hw_param_max() returns less than zero.
This patch makes sure we never leak.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

- add some WARN_ONCE
- add multi-I/O helper (and use helper struct)
- fix off-by-1 DMA length bug
- better variable naming
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

- much improved implementation due to clean codec hierarchy
- preparation for potential per-codec spinlock change

NOTE: additionally removes a chip->pcm[codec_type] NULL ptr check
(due to it requiring access to external chip struct),
however I believe this to be ok since this condition should not occur
and most drivers don't check against that either.
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

- use a separate variable for the frequency part, don't always "or" it
- use a "clever"(?) macro to shorten the code
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

- correct samples to be POSIX shell compatible
- add logging of jiffies value in _pointer()
- several comments
- cleanup
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

flush_scheduled_work() is deprecated and scheduled to be removed.

* cancel[_delayed]_work() + flush_scheduled_work() ->
  cancel[_delayed]_work_sync().

* wm8350, wm8753 and soc-core use custom code to cancel a delayed
  work, execute it immediately if it was pending and wait for its
  completion.  This is equivalent to flush_delayed_work_sync().  Use
  it instead.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It does not make sense to set clientdata to onyx in onyx_i2c_remove()
as we are going to kfree onyx.
What we really want here is i2c_set_clientdata(client, NULL);
Since the i2c core will take care of it now, so this patch just removes it.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Rev. E of the M-Audio Delta 66 is partially supported (commit
ef2cd2cc), but the layout of the GPIO
pins was still unclear. This patch adds the GPIO definitions so that
communication to the CS8247 & 2x AK4524 works correctly.

ALSA bug#3327 has more details; users cap & jhunt report there that the
GPIO wiring is similar to the Digigram VX442 (chip select: pin 4 =
CS8427, pin 5 = AK4524 #0, pin 6 = AK4524 #1).  There has been a lot of
conflicting information in the bug, but given these definitions, my
Delta 66E works; I tested analog in&out at 44.1kHz & 96kHz, analog gain
settings, S/PDIF clock sync, and S/PDIF in&out at 44.1kHz.
Signed-off-by: NBrian Bloniarz <brian.bloniarz@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  ocfs2_connection_find() returns pointer to bad structure
  ocfs2: char is not always signed
  Ocfs2: Stop tracking a negative dentry after dentry_iput().
  ocfs2: fix memory leak
  fs/ocfs2/dlm: Use GFP_ATOMIC under spin_lock

Commit 0ea12930 ("arm: return both physical and virtual addresses
from addruart") took out the test for MMU on/off but didn't switch the
ldr instructions to no longer be conditionals based on said test.

Fix that.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NColin Cross <ccross@android.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM / Hibernate: Fix memory corruption related to swap
  PM / Hibernate: Use async I/O when reading compressed hibernation image

There is a problem that swap pages allocated before the creation of
a hibernation image can be released and used for storing the contents
of different memory pages while the image is being saved.  Since the
kernel stored in the image doesn't know of that, it causes memory
corruption to occur after resume from hibernation, especially on
systems with relatively small RAM that need to swap often.

This issue can be addressed by keeping the GFP_IOFS bits clear
in gfp_allowed_mask during the entire hibernation, including the
saving of the image, until the system is finally turned off or
the hibernation is aborted.  Unfortunately, for this purpose
it's necessary to rework the way in which the hibernate and
suspend code manipulates gfp_allowed_mask.

This change is based on an earlier patch from Hugh Dickins.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reported-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NHugh Dickins <hughd@google.com>
Reviewed-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: stable@kernel.org

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 6524/1: GIC irq desciptor bug fix
  ARM: 6523/1: iop: ensure sched_clock() is notrace
  ARM: 6456/1: Fix for building DEBUG with sa11xx_base.c as a module.
  ARM: 6519/1: kuser: Fix incorrect cmpxchg syscall in kuser helpers
  ARM: 6505/1: kprobes: Don't HAVE_KPROBES when CONFIG_THUMB2_KERNEL is selected
  ARM: 6508/1: vexpress: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
  ARM: 6507/1: RealView: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
  ARM: 6504/1: Thumb-2: Fix long-distance conditional branches in head.S for Thumb-2.
  ARM: 6503/1: Thumb-2: Restore sensible zImage header layout for CONFIG_THUMB2_KERNEL
  ARM: 6502/1: Thumb-2: Fix CONFIG_THUMB2_KERNEL breakage in compressed/head.S
  ARM: 6501/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in mm/proc-v7.S
  ARM: 6500/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in kernel/head.S
  ARM: 6499/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in bootp/init.S
  ARM: 6498/1: vfp: Correct data alignment for CONFIG_THUMB2_KERNEL
  ARM: 6497/1: kexec: Correct data alignment for CONFIG_THUMB2_KERNEL
  ARM: 6496/1: GIC: Do not try to register more then NR_IRQS interrupts
  ARM: cns3xxx: Fix build with CONFIG_PCI=y