Use the macros and defines from mpc85xx.h to simplify
and prevent errors in identifying a mpc85xx based SoC
for errata detection.
This should help enabling (and identifying) workarounds
for various mpc85xx based chips and revisions.
For instance, express MPC8548 Rev.2 as:
(SVR_SOC_VER(svr) == SVR_8548) && (SVR_REV(svr) == 0x20)
instead of:
(pvr == 0x80210020 && mod == 0x8030 && rev == 0x0020)
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A002 is still in "no plans to fix" state, and applies to all
the current P1/P2 parts as well, so it's resonable to enable
its workaround by default, for all the soc's with etsec.
The impact of not enabling this workaround for affected parts
is that under certain conditons (runt frames or even frames
with RX error detected at PHY level) during controller reset,
the controller might fail to indicate Rx reset (GRS) completion.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.

For instance:

	fsl,cksel = <0>;

for using external (TSEC_TMR_CLK input) high precision timer
reference clock.

Other acceptable values:

	<1> : eTSEC system clock
	<2> : eTSEC1 transmit clock
	<3> : RTC clock input

When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: NAida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: NKumar Gala <galak@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 894116bd.

I applied the wrong version of this patch, correct
version coming up.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.

For instance:

	fsl,cksel = <0>;

for using external (TSEC_TMR_CLK input) high precision timer
reference clock.

Other acceptable values:

	<1> : eTSEC system clock
	<2> : eTSEC1 transmit clock
	<3> : RTC clock input

When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: NAida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/freescale/fec_main.c

It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug: error to get the previous BD entry. When the current BD
is the first BD, the previous BD entry must be the last BD,
not "bdp - 1" in current logic.

V4:
  * Optimize fec_enet_get_nextdesc() for code clean.
    Replace "ex_new_bd - ring_size" with "ex_base".
    Replace "new_bd - ring_size" with "base".

V3:
  * Restore the API name because David suggest to use fec_enet_
    prefix for all function in fec driver.
    So, change next_bd() -> fec_enet_get_nextdesc()
        change pre_bd()  -> fec_enet_get_prevdesc()
  * Reduce the two APIs parameters for easy to call.

V2:
  * Add tx_ring_size and rx_ring_size to struct fec_enet_private.
  * Replace api fec_enet_get_nextdesc() with next_bd().
    Replace api fec_enet_get_prevdesc() with pre_bd().

  * Move all ring size check logic to next_bd() and pre_bd(), which
    simplifies the code redundancy.

V1:
  * Add BD ring size check to get the previous BD entry in correctly.
Reviewed-by: NLi Frank <B20596@freescale.com>
Signed-off-by: NFugang Duan  <B38611@freescale.com>
Acked-by: NFrank Li <frank.li@freescale.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the amount of sent bytes reported to BQL by reporting the
number of bytes on wire in the xmit routine, and recording that
value for each skb in order to be correctly confirmed on Tx
confirmation cleanup.

Reporting skb->len to BQL just before exiting xmit is not correct
due to possible insertions of TOE block and alignment bytes in the
skb->data, which are being stripped off by the controller before
transmission on wire.  This led to mismatch of (incorrectly)
reported bytes to BQL b/w xmit and Tx confirmation, resulting in
Tx timeout firing, for the h/w tx timestamping acceleration case.

There's no easy way to obtain the number of bytes on wire in the Tx
confirmation routine, so skb->cb is used to convey that information
from xmit to Tx confirmation, for now (as proposed by Eric). Revived
the currently unused GFAR_CB() construct for that purpose.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit dc975382 "net: fec: add napi support to improve proformance"
converted the fec driver to the napi model. However, that commit
forgot to remove the call to skb_defer_rx_timestamp which is only
needed in non-napi drivers.

(The function napi_gro_receive eventually calls netif_receive_skb,
which in turn calls skb_defer_rx_timestamp.)

This patch should also be applied to the 3.9 and 3.10 kernels.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

My static checker complains that on some arches unsigned longs can be 8
characters which is larger than the buffer is only 6 chars.
Additionally, Ben Hutchings points out that the buffer actually holds
big endian data and the buffer we are reading from is CPU endian.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NFugang Duan  <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a custom 'FEC_NAPI_WEIGHT', just use the generic
'NAPI_POLL_WEIGHT' definition instead.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

make the Freescale ethernet driver get, prepare and enable the FEC clock
during probe(); disable and unprepare the clock upon remove(), put is
done by the devm approach; hold a reference to the clock over the period
of use.

clock lookup is non-fatal as not all platforms provide clock specs in
their device tree; failure to enable specified clocks is fatal.
Signed-off-by: NGerhard Sittig <gsi@denx.de>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 720a43ef
(drivers:net: Remove unnecessary OOM messages after netdev_alloc_skb)
there is a build warning:

drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c: In function 'tx_skb_align_workaround':
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c:586:26: warning: unused variable 'fep'

Fix it.
Signed-off-by: NGerhard Sittig <gsi@denx.de>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: NLibo Chen <libo.chen@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: NLibo Chen <libo.chen@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: NLibo Chen <libo.chen@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: NLibo Chen <libo.chen@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &ofdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: NLibo Chen <libo.chen@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: NLibo Chen <libo.chen@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits.  These bits must not be set
however when eTSEC is operated in Half-Duplex mode.  Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface.  When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner.  If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A).  Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: NLutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanup gfar_start_xmit()'s fast path by factoring out "redundant"
FCB insertion code (repeated gfar_add_fcb() calls and related)
and by reducing the number of if() clauses (i.e. if(fcb) checks).
Improve maintainability (e.g. there's less code and easier to read)
also by introducing do_csum and do_vlan to mark the other 2 Tx TOE
functionalities, following the same model as do_tstamp.
fcb_len may also be 0 now, to mark that Tx FCB insertion conditions
(do_csum, do_vlan, do_tstamp) have not been met.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both [eTSEC76] and [eTSEC12] errata relate to Tx checksum generation
(for some MPC83xx and MCP8548 older revisions). They require the same
workaround: manual checksum computation and insertion, and disabling
the H/W Tx csum acceleration feature (per frame) through Tx FCB
(Frame Control Block) csum offload settings.

The workaround for [eTSEC76] needs to be fixed because it currently
fails to disable H/W Tx csum insertion via FCB. This patch fixes it
and provides a common workaround implementation for both Tx csum errata.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

grp->grp_id is obsolete. It has no use in the current driver.
Remove it from gfar_priv_grp and put the 'rstat' member
in its place, in the 2nd cache line, as rstat needs fast access.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't test for having link and let hardware deal with this situation.

Without this patch I see a machine running an -rt patched Linux being
stuck in sch_direct_xmit when it looses link while there is still a
packet to be sent. In this case the fec_enet_start_xmit routine returned
NETDEV_TX_BUSY which makes the network stack reschedule the packet and
so sch_direct_xmit calls fec_enet_start_xmit again.
I failed to reproduce a complete hang without -rt, but I think the
problem exists there, too.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].

Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.

This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.

How to test:
while [ true ]
do
	ping <IP> -s 10000 -w 4
	ping <IP> -s 6000 -w 2
	ping <IP> -s 4000 -w 2
	ping <IP> -s 10000 -w 2
done

You will see below result in overnight test.

6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms

After apply this patch, >1000ms delay disappear.
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Acked-by: NFugang Duan  <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add MODULE_ALIAS, so that auto module loading can work.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using devm_request_irq() can make the code smaller and cleaner.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As devm_ioremap_resource() is used, there is no need to explicitely check the
return value from platform_get_resource(), as this is something that
devm_ioremap_resource() takes care by itself.

Also, place platform_get_resource() prior to devm_ioremap_resource() for
better code readability.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clk_ptp should also be enabled in fec_resume() and disabled in fec_suspend().
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On fec_probe the clocks are enabled in the following order:

clk_ahb -> clk_ipg -> clk_enet_out -> clk_ptp

, so in the error and remove paths we should disabled them in the opposite
order.

Also fix the order in the suspend/resume functions.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clk_enet_out and clk_ptp are optional clocks, so we should not enable/disable
them unconditionally.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This enables the driver to take advantage of the FEC VLAN
indicator to improve performance.
Signed-off-by: NJim Baxter <jim_baxter@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 38ae92dc "fec: Add support for reading
RMON registers" causes the imx6Q to crash.

This fixes it by only enabling the RMON registers, the
registers are already cleared by the MAC being reset.
Signed-off-by: NJim Baxter <jim_baxter@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tx_bytes field was not being updated so the
network card statistics showed 0.0B transmitted.
Signed-off-by: NJim Baxter <jim_baxter@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setup the multicast list of the net_device instead of
clearing it blindly. This restores the multicast groups
in case of a link down/up event or when resuming from
suspend.
Signed-off-by: NChristoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethtool operation to read RMON registers.

Tested against net-next on i.MX28.

v2: make conditional on #ifndef CONFIG_M5272
Signed-off-by: NChris Healy <cphealy@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All drivers that select MII also need to select NET_CORE because MII
depends on it.  This is a bit ridiculous because NET_CORE is just a
menu option that doesn't enable any code by itself.

There is also no need for it to be a visible option, since its users
all select it.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commits 4c09eed9 (net: fec: Enable imx6 enet checksum acceleration) and
baa70a5c (net: fec: enable pause frame to improve rx prefomance for 1G
network) introduced functionality into the FEC driver which is not
supported on MCF5272. The registers used to implement this functionality
do not exist on MCF5272. Since register defines for MCF5272 are separate
from register defines for other chips, building images for MCF5272 fails
as follows.

fec_main.c: In function 'fec_restart':
fec_main.c:520:8: error: 'FEC_RACC' undeclared (first use in this function)
fec_main.c:585:3: error: 'FEC_R_FIFO_RSEM' undeclared (first use in this function)
fec_main.c:586:3: error: 'FEC_R_FIFO_RSFL' undeclared (first use in this function)
fec_main.c:587:3: error: 'FEC_R_FIFO_RAEM' undeclared (first use in this function)
fec_main.c:588:3: error: 'FEC_R_FIFO_RAFL' undeclared (first use in this function)
fec_main.c:591:3: error: 'FEC_OPD' undeclared (first use in this function)

Adding the missing register defines is not an option, since the registers
do not exist on MCF5272. Disable the added functionality for MCF5272 builds.

Cc: Frank Li <Frank.Li@freescale.com>
Cc: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>