The PCP (per-cpu page allocator in page_alloc.c) shares locking
requirements with vmstat and the zone lock which is inconvenient and
causes some issues.  For example, the PCP list and vmstat share the same
per-cpu space meaning that it's possible that vmstat updates dirty cache
lines holding per-cpu lists across CPUs unless padding is used.  Second,
PREEMPT_RT does not want to disable IRQs for too long in the page
allocator.

This series splits the locking requirements and uses locks types more
suitable for PREEMPT_RT, reduces the time when special locking is required
for stats and reduces the time when IRQs need to be disabled on
!PREEMPT_RT kernels.

Why local_lock?  PREEMPT_RT considers the following sequence to be unsafe
as documented in Documentation/locking/locktypes.rst

   local_irq_disable();
   spin_lock(&lock);

The pcp allocator has this sequence for rmqueue_pcplist (local_irq_save)
-> __rmqueue_pcplist -> rmqueue_bulk (spin_lock).  While it's possible to
separate this out, it generally means there are points where we enable
IRQs and reenable them again immediately.  To prevent a migration and the
per-cpu pointer going stale, migrate_disable is also needed.  That is a
custom lock that is similar, but worse, than local_lock.  Furthermore, on
PREEMPT_RT, it's undesirable to leave IRQs disabled for too long.  By
converting to local_lock which disables migration on PREEMPT_RT, the
locking requirements can be separated and start moving the protections for
PCP, stats and the zone lock to PREEMPT_RT-safe equivalent locking.  As a
bonus, local_lock also means that PROVE_LOCKING does something useful.

After that, it's obvious that zone_statistics incurs too much overhead and
leaves IRQs disabled for longer than necessary on !PREEMPT_RT kernels.
zone_statistics uses perfectly accurate counters requiring IRQs be
disabled for parallel RMW sequences when inaccurate ones like vm_events
would do.  The series makes the NUMA statistics (NUMA_HIT and friends)
inaccurate counters that then require no special protection on
!PREEMPT_RT.

The bulk page allocator can then do stat updates in bulk with IRQs enabled
which should improve the efficiency.  Technically, this could have been
done without the local_lock and vmstat conversion work and the order
simply reflects the timing of when different series were implemented.

Finally, there are places where we conflate IRQs being disabled for the
PCP with the IRQ-safe zone spinlock.  The remainder of the series reduces
the scope of what is protected by disabled IRQs on !PREEMPT_RT kernels.
By the end of the series, page_alloc.c does not call local_irq_save so the
locking scope is a bit clearer.  The one exception is that modifying
NR_FREE_PAGES still happens in places where it's known the IRQs are
disabled as it's harmless for PREEMPT_RT and would be expensive to split
the locking there.

No performance data is included because despite the overhead of the stats,
it's within the noise for most workloads on !PREEMPT_RT.  However, Jesper
Dangaard Brouer ran a page allocation microbenchmark on a E5-1650 v4 @
3.60GHz CPU on the first version of this series.  Focusing on the array
variant of the bulk page allocator reveals the following.

(CPU: Intel(R) Xeon(R) CPU E5-1650 v4 @ 3.60GHz)
ARRAY variant: time_bulk_page_alloc_free_array: step=bulk size

         Baseline        Patched
 1       56.383          54.225 (+3.83%)
 2       40.047          35.492 (+11.38%)
 3       37.339          32.643 (+12.58%)
 4       35.578          30.992 (+12.89%)
 8       33.592          29.606 (+11.87%)
 16      32.362          28.532 (+11.85%)
 32      31.476          27.728 (+11.91%)
 64      30.633          27.252 (+11.04%)
 128     30.596          27.090 (+11.46%)

While this is a positive outcome, the series is more likely to be
interesting to the RT people in terms of getting parts of the PREEMPT_RT
tree into mainline.

This patch (of 9):

The per-cpu page allocator lists and the per-cpu vmstat deltas are stored
in the same struct per_cpu_pages even though vmstats have no direct impact
on the per-cpu page lists.  This is inconsistent because the vmstats for a
node are stored on a dedicated structure.  The bigger issue is that the
per_cpu_pages structure is not cache-aligned and stat updates either cache
conflict with adjacent per-cpu lists incurring a runtime cost or padding
is required incurring a memory cost.

This patch splits the per-cpu pagelists and the vmstat deltas into
separate structures.  It's mostly a mechanical conversion but some
variable renaming is done to clearly distinguish the per-cpu pages
structure (pcp) from the vmstats (pzstats).

Superficially, this appears to increase the size of the per_cpu_pages
structure but the movement of expire fills a structure hole so there is no
impact overall.

[mgorman@techsingularity.net: make it W=1 cleaner]
  Link: https://lkml.kernel.org/r/20210514144622.GA3735@techsingularity.net
[mgorman@techsingularity.net: make it W=1 even cleaner]
  Link: https://lkml.kernel.org/r/20210516140705.GB3735@techsingularity.net
[lkp@intel.com: check struct per_cpu_zonestat has a non-zero size]
[vbabka@suse.cz: Init zone->per_cpu_zonestats properly]

Link: https://lkml.kernel.org/r/20210512095458.30632-1-mgorman@techsingularity.net
Link: https://lkml.kernel.org/r/20210512095458.30632-2-mgorman@techsingularity.netSigned-off-by: NMel Gorman <mgorman@techsingularity.net>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit "mm/page_alloc: convert per-cpu list protection to local_lock" will
introduce a zero-sized per-CPU variable, which causes pahole to generate
invalid BTF.  Only pahole versions 1.18 through 1.21 are impacted, as
before 1.18 pahole doesn't know anything about per-CPU variables, and 1.22
contains the proper fix for the issue.

Luckily, pahole 1.18 got --skip_encoding_btf_vars option disabling BTF
generation for per-CPU variables in anticipation of some unanticipated
problems.  So use this escape hatch to disable per-CPU var BTF info on
those problematic pahole versions.  Users relying on availability of
per-CPU var BTFs would need to upgrade to pahole 1.22+, but everyone won't
notice any regressions.

Link: https://lkml.kernel.org/r/20210530002536.3193829-1-andrii@kernel.orgSigned-off-by: NAndrii Nakryiko <andrii@kernel.org>
Acked-by: NMel Gorman <mgorman@techsingularity.net>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Hao Luo <haoluo@google.com>
Cc: Michal Suchanek <msuchanek@suse.de>
Cc: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Having such debug messages in the dmesg log may confuse users.  Therefore
restrict debug output to cases where DEBUG is defined or dynamic debugging
is enabled for the respective code piece.

Link: https://lkml.kernel.org/r/976adb93-3041-ce63-48fc-55a6096a51c1@gmail.comSigned-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the memmap is virtually contiguous (either because we're using a
virtually mapped memmap or because we don't support a discontig memmap at
all), then we can implement nth_page() by simple addition.  Contrary to
popular belief, the compiler is not able to optimise this itself for a
vmemmap configuration.  This reduces one example user (sg.c) by four
instructions:

        struct page *page = nth_page(rsv_schp->pages[k], offset >> PAGE_SHIFT);

before:
   49 8b 45 70             mov    0x70(%r13),%rax
   48 63 c9                movslq %ecx,%rcx
   48 c1 eb 0c             shr    $0xc,%rbx
   48 8b 04 c8             mov    (%rax,%rcx,8),%rax
   48 2b 05 00 00 00 00    sub    0x0(%rip),%rax
           R_X86_64_PC32      vmemmap_base-0x4
   48 c1 f8 06             sar    $0x6,%rax
   48 01 d8                add    %rbx,%rax
   48 c1 e0 06             shl    $0x6,%rax
   48 03 05 00 00 00 00    add    0x0(%rip),%rax
           R_X86_64_PC32      vmemmap_base-0x4

after:
   49 8b 45 70             mov    0x70(%r13),%rax
   48 63 c9                movslq %ecx,%rcx
   48 c1 eb 0c             shr    $0xc,%rbx
   48 c1 e3 06             shl    $0x6,%rbx
   48 03 1c c8             add    (%rax,%rcx,8),%rbx

Link: https://lkml.kernel.org/r/20210413194625.1472345-1-willy@infradead.orgSigned-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Reviewed-by: NZi Yan <ziy@nvidia.com>
Reviewed-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Douglas Gilbert <dougg@torque.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that compound_head() accepts a const struct page pointer, these two
functions can be marked as not modifying the page pointer they are passed.

Link: https://lkml.kernel.org/r/20210416231531.2521383-7-willy@infradead.orgSigned-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: NVlastimil Babka <vbabka@suse.cz>
Reviewed-by: NAnshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: NWilliam Kucharski <william.kucharski@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The struct page is not modified by these routines, so it can be marked
const.

Link: https://lkml.kernel.org/r/20210416231531.2521383-6-willy@infradead.orgSigned-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: NVlastimil Babka <vbabka@suse.cz>
Reviewed-by: NAnshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: NWilliam Kucharski <william.kucharski@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If you pass a const pointer to compound_head(), you get a const pointer
back; if you pass a mutable pointer, you get a mutable pointer back.  Also
remove an unnecessary forward definition of struct page; we're about to
dereference page->compound_head, so it must already have been defined.

Link: https://lkml.kernel.org/r/20210416231531.2521383-5-willy@infradead.orgSigned-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: NVlastimil Babka <vbabka@suse.cz>
Reviewed-by: NAnshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: NWilliam Kucharski <william.kucharski@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

dump_page_owner() only uses struct page to find the page_ext, and
lookup_page_ext() already takes a const argument.

Link: https://lkml.kernel.org/r/20210416231531.2521383-4-willy@infradead.orgSigned-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: NVlastimil Babka <vbabka@suse.cz>
Reviewed-by: NAnshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: NWilliam Kucharski <william.kucharski@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move the PagePoisoned test into dump_page().  Skip the hex print for
poisoned pages -- we know they're full of ffffffff.  Move the reason
printing from __dump_page() to dump_page().

Link: https://lkml.kernel.org/r/20210416231531.2521383-3-willy@infradead.orgSigned-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: NVlastimil Babka <vbabka@suse.cz>
Reviewed-by: NAnshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: NWilliam Kucharski <william.kucharski@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A customer experienced a low-memory situation and decided to issue a
SIGKILL (i.e.  a fatal signal).  Instead of promptly terminating as one
would expect, the aforementioned task remained unresponsive.

Further investigation indicated that the task was "stuck" in the
reclaim/compaction retry loop.  Now, it does not make sense to retry
compaction when a fatal signal is pending.

In the context of try_to_compact_pages(), indeed COMPACT_SKIPPED can be
returned; albeit, not every zone, on the zone list, would be considered in
the case a fatal signal is found to be pending.  Yet, in
should_compact_retry(), given the last known compaction result, each zone,
on the zone list, can be considered/or checked (see
compaction_zonelist_suitable()).  For example, if a zone was found to
succeed, then reclaim/compaction would be tried again (notwithstanding the
above).

This patch ensures that compaction is not needlessly retried irrespective
of the last known compaction result e.g.  if it was skipped, in the
unlikely case a fatal signal is found pending.  So, OOM is at least
attempted.

Link: https://lkml.kernel.org/r/20210520142901.3371299-1-atomlin@redhat.comSigned-off-by: NAaron Tomlin <atomlin@redhat.com>
Reviewed-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Patch series "Constify struct page arguments".

While working on various solutions to the 32-bit struct page size
regression, one of the problems I found was the networking stack expects
to be able to pass const struct page pointers around, and the mm doesn't
provide a lot of const-friendly functions to call.  The root tangle of
problems is that a lot of functions call VM_BUG_ON_PAGE(), which calls
dump_page(), which calls a lot of functions which don't take a const
struct page (but could be const).

This patch (of 6):

The only caller of __dump_page() now opencodes dump_page(), so remove it
as an externally visible symbol.

Link: https://lkml.kernel.org/r/20210416231531.2521383-1-willy@infradead.org
Link: https://lkml.kernel.org/r/20210416231531.2521383-2-willy@infradead.orgSigned-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: NVlastimil Babka <vbabka@suse.cz>
Reviewed-by: NAnshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: NWilliam Kucharski <william.kucharski@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There is a lot of historical ifdefery in is_highmem_idx() and its helper
zone_movable_is_highmem() that was required because of two different paths
for nodes and zones initialization that were selected at compile time.

Until commit 3f08a302 ("mm: remove CONFIG_HAVE_MEMBLOCK_NODE_MAP
option") the movable_zone variable was only available for configurations
that had CONFIG_HAVE_MEMBLOCK_NODE_MAP enabled so the test in
zone_movable_is_highmem() used that variable only for such configurations.
For other configurations the test checked if the index of ZONE_MOVABLE
was greater by 1 than the index of ZONE_HIGMEM and then movable zone was
considered a highmem zone.  Needless to say, ZONE_MOVABLE - 1 equals
ZONE_HIGHMEM by definition when CONFIG_HIGHMEM=y.

Commit 3f08a302 ("mm: remove CONFIG_HAVE_MEMBLOCK_NODE_MAP option")
made movable_zone variable always available.  Since this variable is set
to ZONE_HIGHMEM if CONFIG_HIGHMEM is enabled and highmem zone is
populated, it is enough to check whether

	zone_idx == ZONE_MOVABLE && movable_zone == ZONE_HIGMEM

to test if zone index points to a highmem zone.

Remove zone_movable_is_highmem() that is not used anywhere except
is_highmem_idx() and use the test above in is_highmem_idx() instead.

Link: https://lkml.kernel.org/r/20210426141927.1314326-3-rppt@kernel.orgSigned-off-by: NMike Rapoport <rppt@linux.ibm.com>
Reviewed-by: NAnshuman Khandual <anshuman.khandual@arm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add the details for figuring out which parts of the kernel image is being
freed on initmem case.

Before:
   Freeing unused kernel memory: 1024K

After:
   Freeing unused kernel image (initmem) memory: 1024K

Link: https://lkml.kernel.org/r/1622706274-4533-1-git-send-email-js07.lee@samsung.comSigned-off-by: NJungseung Lee <js07.lee@samsung.com>
Reviewed-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add memory corruption identification support for hardware tag-based mode.
We store one old free pointer tag and free backtrace instead of five
because hardware tag-based kasan only has 16 different tags.

If we store as many stacks as SW tag-based kasan does(5 stacks), there is
high probability to find the same tag in the stacks when out-of-bound
issues happened and we will mistake out-of-bound issue for use-after-free.

Link: https://lkml.kernel.org/r/20210626100931.22794-4-Kuan-Ying.Lee@mediatek.comSigned-off-by: NKuan-Ying Lee <Kuan-Ying.Lee@mediatek.com>
Suggested-by: NMarco Elver <elver@google.com>
Reviewed-by: NAlexander Potapenko <glider@google.com>
Reviewed-by: NAndrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: NMarco Elver <elver@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Nicholas Tang <nicholas.tang@mediatek.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

1. Move kasan_get_free_track() and kasan_set_free_info() into tags.c
   and combine these two functions for SW_TAGS and HW_TAGS kasan mode.

2. Move kasan_get_bug_type() to report_tags.c and make this function
   compatible for SW_TAGS and HW_TAGS kasan mode.

Link: https://lkml.kernel.org/r/20210626100931.22794-3-Kuan-Ying.Lee@mediatek.comSigned-off-by: NKuan-Ying Lee <Kuan-Ying.Lee@mediatek.com>
Suggested-by: NMarco Elver <elver@google.com>
Suggested-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: NAndrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: NMarco Elver <elver@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Nicholas Tang <nicholas.tang@mediatek.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Patch series "kasan: add memory corruption identification support for hw tag-based kasan", v4.

Add memory corruption identification for hardware tag-based KASAN mode.

This patch (of 3):

Rename CONFIG_KASAN_SW_TAGS_IDENTIFY to CONFIG_KASAN_TAGS_IDENTIFY in
order to be compatible with hardware tag-based mode.

Link: https://lkml.kernel.org/r/20210626100931.22794-1-Kuan-Ying.Lee@mediatek.com
Link: https://lkml.kernel.org/r/20210626100931.22794-2-Kuan-Ying.Lee@mediatek.comSigned-off-by: NKuan-Ying Lee <Kuan-Ying.Lee@mediatek.com>
Suggested-by: NMarco Elver <elver@google.com>
Reviewed-by: NAlexander Potapenko <glider@google.com>
Reviewed-by: NAndrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: NMarco Elver <elver@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: Nicholas Tang <nicholas.tang@mediatek.com>
Cc: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

powerpc has a variable number of PTRS_PER_*, set at runtime based on the
MMU that the kernel is booted under.

This means the PTRS_PER_* are no longer constants, and therefore breaks
the build.  Switch to using MAX_PTRS_PER_*, which are constant.

Link: https://lkml.kernel.org/r/20210624034050.511391-5-dja@axtens.netSigned-off-by: NDaniel Axtens <dja@axtens.net>
Suggested-by: NChristophe Leroy <christophe.leroy@csgroup.eu>
Suggested-by: NBalbir Singh <bsingharora@gmail.com>
Reviewed-by: NChristophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: NBalbir Singh <bsingharora@gmail.com>
Reviewed-by: NMarco Elver <elver@google.com>
Reviewed-by: NAndrey Konovalov <andreyknvl@gmail.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit c65e774f ("x86/mm: Make PGDIR_SHIFT and PTRS_PER_P4D variable")
made PTRS_PER_P4D variable on x86 and introduced MAX_PTRS_PER_P4D as a
constant for cases which need a compile-time constant (e.g.  fixed-size
arrays).

powerpc likewise has boot-time selectable MMU features which can cause
other mm "constants" to vary.  For KASAN, we have some static
PTE/PMD/PUD/P4D arrays so we need compile-time maximums for all these
constants.  Extend the MAX_PTRS_PER_ idiom, and place default definitions
in include/pgtable.h.  These define MAX_PTRS_PER_x to be PTRS_PER_x unless
an architecture has defined MAX_PTRS_PER_x in its arch headers.

Clean up pgtable-nop4d.h and s390's MAX_PTRS_PER_P4D definitions while
we're at it: both can just pick up the default now.

Link: https://lkml.kernel.org/r/20210624034050.511391-4-dja@axtens.netSigned-off-by: NDaniel Axtens <dja@axtens.net>
Acked-by: NAndrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: NChristophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: NMarco Elver <elver@google.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow architectures to define a kasan_arch_is_ready() hook that bails out
of any function that's about to touch the shadow unless the arch says that
it is ready for the memory to be accessed.  This is fairly uninvasive and
should have a negligible performance penalty.

This will only work in outline mode, so an arch must specify
ARCH_DISABLE_KASAN_INLINE if it requires this.

Link: https://lkml.kernel.org/r/20210624034050.511391-3-dja@axtens.netSigned-off-by: NDaniel Axtens <dja@axtens.net>
Reviewed-by: NMarco Elver <elver@google.com>
Suggested-by: NChristophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: NAndrey Konovalov <andreyknvl@gmail.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Patch series "KASAN core changes for ppc64 radix KASAN", v16.

Building on the work of Christophe, Aneesh and Balbir, I've ported KASAN
to 64-bit Book3S kernels running on the Radix MMU.  I've been trying this
for a while, but we keep having collisions between the kasan code in the
mm tree and the code I want to put in to the ppc tree.

This series just contains the kasan core changes that we need.  There
should be no noticeable changes to other platforms.

This patch (of 4):

For annoying architectural reasons, it's very difficult to support inline
instrumentation on powerpc64.*

Add a Kconfig flag to allow an arch to disable inline.  (It's a bit
annoying to be 'backwards', but I'm not aware of any way to have an arch
force a symbol to be 'n', rather than 'y'.)

We also disable stack instrumentation in this case as it does things that
are functionally equivalent to inline instrumentation, namely adding code
that touches the shadow directly without going through a C helper.

* on ppc64 atm, the shadow lives in virtual memory and isn't accessible in
real mode.  However, before we turn on virtual memory, we parse the device
tree to determine which platform and MMU we're running under.  That calls
generic DT code, which is instrumented.  Inline instrumentation in DT
would unconditionally attempt to touch the shadow region, which we won't
have set up yet, and would crash.  We can make outline mode wait for the
arch to be ready, but we can't change what the compiler inserts for inline
mode.

Link: https://lkml.kernel.org/r/20210624034050.511391-1-dja@axtens.net
Link: https://lkml.kernel.org/r/20210624034050.511391-2-dja@axtens.netSigned-off-by: NDaniel Axtens <dja@axtens.net>
Reviewed-by: NMarco Elver <elver@google.com>
Reviewed-by: NAndrey Konovalov <andreyknvl@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The KUNIT_EXPECT_KASAN_FAIL() macro currently uses KUNIT_EXPECT_EQ() to
compare fail_data.report_expected and fail_data.report_found.  This always
gave a somewhat useless error message on failure, but the addition of
extra compile-time checking with READ_ONCE() has caused it to get much
longer, and be truncated before anything useful is displayed.

Instead, just check fail_data.report_found by hand (we've just set
report_expected to 'true'), and print a better failure message with
KUNIT_FAIL().  Because of this, report_expected is no longer used
anywhere, and can be removed.

Beforehand, a failure in:
KUNIT_EXPECT_KASAN_FAIL(test, ((volatile char *)area)[3100]);
would have looked like:
[22:00:34] [FAILED] vmalloc_oob
[22:00:34]     # vmalloc_oob: EXPECTATION FAILED at lib/test_kasan.c:991
[22:00:34]     Expected ({ do { extern void __compiletime_assert_705(void) __attribute__((__error__("Unsupported access size for {READ,WRITE}_ONCE()."))); if (!((sizeof(fail_data.report_expected) == sizeof(char) || sizeof(fail_data.repp
[22:00:34]     not ok 45 - vmalloc_oob

With this change, it instead looks like:
[22:04:04] [FAILED] vmalloc_oob
[22:04:04]     # vmalloc_oob: EXPECTATION FAILED at lib/test_kasan.c:993
[22:04:04]     KASAN failure expected in "((volatile char *)area)[3100]", but none occurred
[22:04:04]     not ok 45 - vmalloc_oob

Also update the example failure in the documentation to reflect this.

Link: https://lkml.kernel.org/r/20210606005531.165954-1-davidgow@google.comSigned-off-by: NDavid Gow <davidgow@google.com>
Reviewed-by: NAndrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: NMarco Elver <elver@google.com>
Acked-by: NBrendan Higgins <brendanhiggins@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: David Gow <davidgow@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Most of the contents of KASAN reports are printed with pr_err(), so use a
consistent logging level to print the memory access stacks.

Link: https://lkml.kernel.org/r/20210506105405.3535023-2-glider@google.comSigned-off-by: NAlexander Potapenko <glider@google.com>
Reviewed-by: NMarco Elver <elver@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Prasad Sodagudi <psodagud@quicinc.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: he, bo <bo.he@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

dump_stack() is used for many different cases, which may require a log
level consistent with other kernel messages surrounding the dump_stack()
call.  Without that, certain systems that are configured to ignore the
default level messages will miss stack traces in critical error reports.

This patch introduces dump_stack_lvl() that behaves similarly to
dump_stack(), but accepts a custom log level.  The old dump_stack()
becomes equal to dump_stack_lvl(KERN_DEFAULT).

A somewhat similar patch has been proposed in 2012:
https://lore.kernel.org/lkml/1332493269.2359.9.camel@hebo/ , but wasn't
merged.

[elver@google.com: add missing dump_stack_lvl() stub if CONFIG_PRINTK=n]
  Link: https://lkml.kernel.org/r/YJ0KAM0hQev1AmWe@elver.google.com

Link: https://lkml.kernel.org/r/20210506105405.3535023-1-glider@google.comSigned-off-by: NAlexander Potapenko <glider@google.com>
Reviewed-by: NMarco Elver <elver@google.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: he, bo <bo.he@intel.com>
Cc: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Cc: Prasad Sodagudi <psodagud@quicinc.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On non-preemptible kernel builds the watchdog can complain about soft
lockups when vfree() is called against large vmalloc areas:

[  210.851798] kvmalloc-test: vmalloc(2199023255552) succeeded
[  238.654842] watchdog: BUG: soft lockup - CPU#181 stuck for 26s! [rmmod:5203]
[  238.662716] Modules linked in: kvmalloc_test(OE-) ...
[  238.772671] CPU: 181 PID: 5203 Comm: rmmod Tainted: G S         OE     5.13.0-rc7+ #1
[  238.781413] Hardware name: Intel Corporation PURLEY/PURLEY, BIOS PLYXCRB1.86B.0553.D01.1809190614 09/19/2018
[  238.792383] RIP: 0010:free_unref_page+0x52/0x60
[  238.797447] Code: 48 c1 fd 06 48 89 ee e8 9c d0 ff ff 84 c0 74 19 9c 41 5c fa 48 89 ee 48 89 df e8 b9 ea ff ff 41 f7 c4 00 02 00 00 74 01 fb 5b <5d> 41 5c c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 f0 29 77
[  238.818406] RSP: 0018:ffffb4d87868fe98 EFLAGS: 00000206
[  238.824236] RAX: 0000000000000000 RBX: 000000001da0c945 RCX: ffffb4d87868fe40
[  238.832200] RDX: ffffd79d3beed108 RSI: ffffd7998501dc08 RDI: ffff9c6fbffd7010
[  238.840166] RBP: 000000000d518cbd R08: ffffd7998501dc08 R09: 0000000000000001
[  238.848131] R10: 0000000000000000 R11: ffffd79d3beee088 R12: 0000000000000202
[  238.856095] R13: ffff9e5be3eceec0 R14: 0000000000000000 R15: 0000000000000000
[  238.864059] FS:  00007fe082c2d740(0000) GS:ffff9f4c69b40000(0000) knlGS:0000000000000000
[  238.873089] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  238.879503] CR2: 000055a000611128 CR3: 000000f6094f6006 CR4: 00000000007706e0
[  238.887467] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  238.895433] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  238.903397] PKRU: 55555554
[  238.906417] Call Trace:
[  238.909149]  __vunmap+0x17c/0x220
[  238.912851]  __x64_sys_delete_module+0x13a/0x250
[  238.918008]  ? syscall_trace_enter.isra.20+0x13c/0x1b0
[  238.923746]  do_syscall_64+0x39/0x80
[  238.927740]  entry_SYSCALL_64_after_hwframe+0x44/0xae

Like in other range zapping routines that iterate over a large list, lets
just add cond_resched() within __vunmap()'s page-releasing loop in order
to avoid the watchdog splats.

Link: https://lkml.kernel.org/r/20210622225030.478384-1-aquini@redhat.comSigned-off-by: NRafael Aquini <aquini@redhat.com>
Acked-by: NNicholas Piggin <npiggin@gmail.com>
Reviewed-by: NUladzislau Rezki (Sony) <urezki@gmail.com>
Reviewed-by: NAaron Tomlin <atomlin@redhat.com>
Acked-by: NMichal Hocko <mhocko@suse.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently for order-0 pages we use a bulk-page allocator to get set of
pages.  From the other hand not allocating all pages is something that
might occur.  In that case we should fallbak to the single-page allocator
trying to get missing pages, because it is more permissive(direct reclaim,
etc).

Introduce a vm_area_alloc_pages() function where the described logic is
implemented.

Link: https://lkml.kernel.org/r/20210521130718.GA17882@pc638.lanSigned-off-by: NUladzislau Rezki (Sony) <urezki@gmail.com>
Reviewed-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A checkpatch.pl script complains on splitting a text across lines.  It is
because if a user wants to find an entire string he or she will not
succeeded.

<snip>
WARNING: quoted string split across lines
+               "vmalloc size %lu allocation failure: "
+               "page order %u allocation failed",

total: 0 errors, 1 warnings, 10 lines checked
<snip>

Link: https://lkml.kernel.org/r/20210521204359.19943-1-urezki@gmail.comSigned-off-by: NUladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a memory allocation for array of pages are not succeed emit a warning
message as a first step and then perform the further cleanup.

The reason it should be done in a right order is the clean up function
which is free_vm_area() can potentially also follow its error paths what
can lead to confusion what was broken first.

Link: https://lkml.kernel.org/r/20210516202056.2120-4-urezki@gmail.comSigned-off-by: NUladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Recently there has been introduced a page bulk allocator for users which
need to get number of pages per one call request.

For order-0 pages switch to an alloc_pages_bulk_array_node() instead of
alloc_pages_node(), the reason is the former is not capable of allocating
set of pages, thus a one call is per one page.

Second, according to my tests the bulk allocator uses less cycles even for
scenarios when only one page is requested.  Running the "perf" on same
test case shows below difference:

<default>
  - 45.18% __vmalloc_node
     - __vmalloc_node_range
        - 35.60% __alloc_pages
           - get_page_from_freelist
                3.36% __list_del_entry_valid
                3.00% check_preemption_disabled
                1.42% prep_new_page
<default>

<patch>
  - 31.00% __vmalloc_node
     - __vmalloc_node_range
        - 14.48% __alloc_pages_bulk
             3.22% __list_del_entry_valid
           - 0.83% __alloc_pages
                get_page_from_freelist
<patch>

The "test_vmalloc.sh" also shows performance improvements:

fix_size_alloc_test_4MB   loops: 1000000 avg: 89105095 usec
fix_size_alloc_test       loops: 1000000 avg: 513672   usec
full_fit_alloc_test       loops: 1000000 avg: 748900   usec
long_busy_list_alloc_test loops: 1000000 avg: 8043038  usec
random_size_alloc_test    loops: 1000000 avg: 4028582  usec
fix_align_alloc_test      loops: 1000000 avg: 1457671  usec

fix_size_alloc_test_4MB   loops: 1000000 avg: 62083711 usec
fix_size_alloc_test       loops: 1000000 avg: 449207   usec
full_fit_alloc_test       loops: 1000000 avg: 735985   usec
long_busy_list_alloc_test loops: 1000000 avg: 5176052  usec
random_size_alloc_test    loops: 1000000 avg: 2589252  usec
fix_align_alloc_test      loops: 1000000 avg: 1365009  usec

For example 4MB allocations illustrates ~30% gain, all the
rest is also better.

Link: https://lkml.kernel.org/r/20210516202056.2120-3-urezki@gmail.comSigned-off-by: NUladzislau Rezki (Sony) <urezki@gmail.com>
Acked-by: NMel Gorman <mgorman@suse.de>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Patch series "vmalloc() vs bulk allocator", v2.

This patch (of 3):

Add a "node" variant of the alloc_pages_bulk_array() function.  The helper
guarantees that a __alloc_pages_bulk() is invoked with a valid NUMA node
ID.

Link: https://lkml.kernel.org/r/20210516202056.2120-1-urezki@gmail.com
Link: https://lkml.kernel.org/r/20210516202056.2120-2-urezki@gmail.comSigned-off-by: NUladzislau Rezki (Sony) <urezki@gmail.com>
Acked-by: NMel Gorman <mgorman@suse.de>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some trace event formats print PFNs as hex while others print them as
decimal.  This is rather annoying when attempting to grep through traces
to understand what's going on with a particular page.

 $ git grep -ho 'pfn=[0x%lu]\+' include/trace/events/ | sort | uniq -c
      11 pfn=0x%lx
      12 pfn=%lu
       2 pfn=%lx

Printing as hex is in the majority in the trace events, and all the normal
printks in mm/ also print PFNs as hex, so change all the PFN formats in
the trace events to use 0x%lx.

Link: https://lkml.kernel.org/r/20210602092608.1493-1-vincent.whitchurch@axis.comSigned-off-by: NVincent Whitchurch <vincent.whitchurch@axis.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jesper Dangaard Brouer <hawk@kernel.org>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use DEVICE_ATTR_RO() helper instead of plain DEVICE_ATTR(), which makes
the code a bit shorter and easier to read.

Link: https://lkml.kernel.org/r/20210524112852.34716-1-yuehaibing@huawei.comSigned-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Kernel test robot throws below warning ->

>> arch/h8300/kernel/setup.c:72:26:
warning: Unused variable: region [unusedVariable]
    struct memblock_region *region;

Fixed it by removing unused variable.

Link: https://lkml.kernel.org/r/20210602185431.11416-1-jrdr.linux@gmail.comSigned-off-by: NSouptick Joarder <jrdr.linux@gmail.com>
Reported-by: Nkernel test robot <lkp@intel.com>
Acked-by: NMike Rapoport <rppt@linux.ibm.com>
Acked-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

1. These tlb flush functions have been using vma instead mm long time
   ago, but there is still some comments use mm as parameter.

2. the actual struct we use is vm_area_struct instead of vma_struct.

3. remove unused flush_kern_tlb_page.

Link: https://lkml.kernel.org/r/87k0oaq311.wl-chenli@uniontech.comSigned-off-by: NChen Li <chenli@uniontech.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

vma_lookup() finds the vma of a specific address with a cleaner interface
and is more readable.

Link: https://lkml.kernel.org/r/20210521174745.2219620-23-Liam.Howlett@Oracle.comSigned-off-by: NLiam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: NLaurent Dufour <ldufour@linux.ibm.com>
Acked-by: NDavid Hildenbrand <david@redhat.com>
Acked-by: NDavidlohr Bueso <dbueso@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use vma_lookup() to find the VMA at a specific address.  As vma_lookup()
will return NULL if the address is not within any VMA, the start address
no longer needs to be validated.

Link: https://lkml.kernel.org/r/20210521174745.2219620-22-Liam.Howlett@Oracle.comSigned-off-by: NLiam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: NLaurent Dufour <ldufour@linux.ibm.com>
Acked-by: NDavid Hildenbrand <david@redhat.com>
Acked-by: NDavidlohr Bueso <dbueso@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use vma_lookup() to find the VMA at a specific address.  As vma_lookup()
will return NULL if the address is not within any VMA, the start address
no longer needs to be validated.

Link: https://lkml.kernel.org/r/20210521174745.2219620-21-Liam.Howlett@Oracle.comSigned-off-by: NLiam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: NLaurent Dufour <ldufour@linux.ibm.com>
Acked-by: NDavid Hildenbrand <david@redhat.com>
Acked-by: NDavidlohr Bueso <dbueso@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use vma_lookup() to find the VMA at a specific address.  As vma_lookup()
will return NULL if the address is not within any VMA, the start address
no longer needs to be validated.

Link: https://lkml.kernel.org/r/20210521174745.2219620-20-Liam.Howlett@Oracle.comSigned-off-by: NLiam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: NLaurent Dufour <ldufour@linux.ibm.com>
Acked-by: NDavid Hildenbrand <david@redhat.com>
Acked-by: NDavidlohr Bueso <dbueso@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use vma_lookup() to find the VMA at a specific address.  As vma_lookup()
will return NULL if the address is not within any VMA, the start address
no longer needs to be validated.

Link: https://lkml.kernel.org/r/20210521174745.2219620-19-Liam.Howlett@Oracle.comSigned-off-by: NLiam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: NLaurent Dufour <ldufour@linux.ibm.com>
Acked-by: NDavid Hildenbrand <david@redhat.com>
Acked-by: NDavidlohr Bueso <dbueso@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use vma_lookup() to find the VMA at a specific address.  As vma_lookup()
will return NULL if the address is not within any VMA, the start address
no longer needs to be validated.

Link: https://lkml.kernel.org/r/20210521174745.2219620-18-Liam.Howlett@Oracle.comSigned-off-by: NLiam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: NLaurent Dufour <ldufour@linux.ibm.com>
Acked-by: NDavid Hildenbrand <david@redhat.com>
Acked-by: NDavidlohr Bueso <dbueso@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use vma_lookup() to find the VMA at a specific address.  As vma_lookup()
will return NULL if the address is not within any VMA, the start address
no longer needs to be validated.

Link: https://lkml.kernel.org/r/20210521174745.2219620-17-Liam.Howlett@Oracle.comSigned-off-by: NLiam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: NLaurent Dufour <ldufour@linux.ibm.com>
Acked-by: NDavid Hildenbrand <david@redhat.com>
Acked-by: NDavidlohr Bueso <dbueso@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>