v3 hardware's packet format is almost identical to v2 (one/three finger touch),
except when sensing two finger touch, the hardware sends 12 bytes of data.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Group property setting code into elantech_set_properties.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

For v2 hardware, there is no real parity check, but we can still check
some constant bits for data integrity.

Also rename elantech_check_parity_v1 to elantech_packet_check_v1 to make
these packet checking function names consistent.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Don't try to be too clever and remove ETP_EDGE_FUZZ_V2. X, Y ranges
should be just the raw resolution of the device. Otherwise, they can
cause underflow on the Y axis.
Suggested-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

With newer hardware, the touchpad provides range info.
Let's use it.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

For two finger touches the coordinate of each finger gets reported
separately but with reduced resolution.

With this change, we now have the same range for ST and MT data and
scale MT data because it has lower resolution to match ST.
Suggested-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

x, y values are actually 12-bit long. Also update protocol document to
reflect the change.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Fix warning from Geert's build summary emails by changing "if" to
"ifdef". Thsi should fix the following:

drivers/input/misc/twl6040-vibra.c:231:5: warning: "CONFIG_PM_SLEEP" is not defined

Builds cleanly with CONFIG_PM_SLEEP enabled or disabled.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Take spinlock when entering ISR and timer routine to ensure that we do not
race while enabling/disabling FIFO interrupts.

Also we do not need to take teh spinlock in tegra_kbc_startremove() since
interrupt is completely disabled.
Tested-by: NRakesh Iyer <riyer@nvidia.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

For wakeup to be reliable, kbc needs to be in interrupt mode before suspend.
Created common routine to control the FIFO interrupt.
Added synchronization to ensure orderly suspend.
Signed-off-by: NRakesh Iyer <riyer@nvidia.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

WARNING: drivers/input/keyboard/built-in.o(.text+0xb55b): Section mismatch in reference from the function tc3589x_keypad_open() to the function .devinit.text:tc3589x_keypad_init_key_hardware()
The function tc3589x_keypad_open() references
the function __devinit tc3589x_keypad_init_key_hardware().
This is often because tc3589x_keypad_open lacks a __devinit
annotation or the annotation of tc3589x_keypad_init_key_hardware is wrong.
Signed-off-by: NHarvey Yang <harvey.huawei.yang@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This flag is a NOOP and can be removed now.
Signed-off-by: NYong Zhang <yong.zhang0@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This commit enables control of the LEDs and OLED displays found on the
Wacom Intuos4 M, L, and XL. For this purpose, a new "wacom_led" attribute
group is added to the sysfs entry of the USB device.

This "wacom_led" group only shows up when the correct device (M, L, or XL)
is detected. The attributes are described in
 Documentation/ABI/testing/sysfs-wacom
Signed-off-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ARM: mach-shmobile: sh7372 LCDC1 suspend fix V2 (incremental)
  OMAP: omap_device: only override _noirq methods, not normal suspend/resume
  PM / Runtime: Correct documentation of pm_runtime_irq_safe()
  ARM: mach-shmobile: sh7372 LCDC1 suspend fix
  sh-sci / PM: Use power.irq_safe
  PM: Use spinlock instead of mutex in clock management functions

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: sbp2: fix panic after rmmod with slow targets

This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
 - Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

This will ensure that the device delivers input events only when there
are users.
Tested-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Instead of using hard IRQ and workqueue solution switch to using threaded
interrupt handler to simplify the code and locking rules.
Tested-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
  drm/i915: Fix wrong initializer for "locked" variable in assert_panel_unlocked
  i915: do not setup intel_backlight twice

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
  USB: ftdi_sio: add Calao reference board support
  USB option driver K3765/K4505 avoid CDC_DATA interface
  USB: option: add YUGA device id to driver
  usb: s5p-ehci: fix a NULL pointer deference
  USB: EHCI: Do not rely on PORT_SUSPEND to stop USB resuming in ehci_bus_resume().
  USB option driver add PID of Huawei Vodafone K4605
  USB option driver add PID of Huawei Vodafone K3806
  xhci: Handle zero-length isochronous packets.
  USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
  usb: musb: gadget: fix error path
  usb: gadget: f_phonet: unlock in error case
  usb: musb: blackfin: include prefetch head file
  usb: musb: tusb6010: fix compilation
  usb: gadget: renesas_usbhs: fix DMA build by including dma-mapping.h
  usb: musb: cppi: fix build errors due to DBG and missing musb variable
  usb: musb: ux500: replace missing DBG with dev_dbg
  usb: musb: ux500: set dma config for both src and dst
  usb: musb: fix oops on musb_gadget_pullup
  usb: host: ehci-omap: fix .remove and failure handling path of .probe(v1)
  usb: gadget: hid: don't STALL when processing a HID Descriptor request
  ...

* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  omap-serial: Allow IXON and IXOFF to be disabled.
  TTY: serial, document ignoring of uart->ops->startup error
  TTY: pty, fix pty counting
  8250: Fix race condition in serial8250_backup_timeout().
  serial/8250_pci: delete duplicate data definition
  8250_pci: add support for Rosewill RC-305 4x serial port card
  tty: Add "spi:" prefix for spi modalias
  atmel_serial: fix atmel_default_console_device
  serial: 8250_pnp: add Intermec CV60 touchscreen device
  drivers/serial/ucc_uart.c: Fix compiler warning
  pch_uart: Set PCIe bus number using probe parameter
  serial: samsung: Fix build error

Merge branch 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6

* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  drivers:misc: ti-st: fix unexpected UART close
  drivers:misc: ti-st: free skb on firmware download
  drivers:misc: ti-st: wait for completion at fail
  drivers:misc: ti-st: reinit completion before send
  drivers:misc: ti-st: fail-safe on wrong pkt type
  drivers:misc: ti-st: reinit completion on ver read
  drivers:misc:ti-st: platform hooks for chip states
  drivers:misc: ti-st: avoid a misleading dbg msg
  base/devres.c: quiet sparse noise about context imbalance
  pti: add missing CONFIG_PCI dependency
  drivers/base/devtmpfs.c: correct annotation of `setup_done'
  driver core: fix kernel-doc warning in platform.c
  firmware: fix google/gsmi.c build warning

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  staging: tidspbridge: fix compilation on dsp clock functions
  staging: octeon-ethernet: Add missing #includes.
  Staging: zcache: signedness bug in tmem_get()
  staging: zcache: fix crash on high memory swap
  staging: brcm80211: SPARC build error fix
  staging: brcm80211: fix compile error on non-x86 archs since 3.0 kernel

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] memory hotplug: only unassign assigned increments
  [S390] Change default action from reipl to stop for on_restart
  [S390] arch/s390/kernel/ipl.c: correct error detection check
  [S390] drivers/s390/block/dasd_ioctl.c: add missing kfree
  [S390] nss,initrd: kernel image and initrd must be in different segments

According to the SFI specification irq number 0xFF means device has no
interrupt or interrupt attached via GPIO.

Currently, we don't handle this special case and set irq field in
*_board_info structs to 255.  It leads to confusion in some drivers.
Accelerometer driver tries to register interrupt 255, fails and prints
"Cannot get IRQ" to dmesg.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (32 commits)
  ALSA: hda: Conexant: Allow different output types to share DAC
  ASoC: Correct element count for WM8996 sidetone HPF
  ASoC: Tegra: wm8903 machine driver: Drop Ventana support
  ASoC: Add samsung maintainer
  ASoC: Add Springbank I/O card to Speyside Kconfig
  ALSA: hda/conexant - Enable ADC-switching for auto-mic mode, too
  ALSA: hda - Fix double-headphone/speaker paths for Cxt auto-parser
  ALSA: hda - Update jack-sense info even when no automute is set
  ALSA: hda - Fix output-path initialization for Realtek auto-parser
  sound/soc/fsl/mpc8610_hpcd.c: add missing of_node_put
  sound/soc/fsl/p1022_ds.c: add missing of_node_put
  sound/soc/ep93xx/ep93xx-i2s.c: add missing kfree
  sound/soc/kirkwood/kirkwood-i2s.c: add missing kfree
  ASoC: soc-core: use GFP_KERNEL flag for kmalloc in snd_soc_cnew
  sound/soc/fsl/fsl_dma.c: add missing of_node_put
  ASoC: Clear completions from late WM8996 FLL lock IRQs
  ASoC: Clear any outstanding WM8962 FLL lock completions before waiting
  ASoC: Ensure we only run Speyside WM8962 bias level callbacks once
  ASoC: Fix configuration of WM8996 input enables
  ASoC: WM8996 record paths need AIFCLK
  ...

This bug causes the IECSR register clear failure.  In this case, the RETE
(retry error threshold exceeded) interrupt will be generated and cannot be
cleared.  So the related ISR may be called persistently.

The RETE bit in IECSR is cleared by writing a 1 to it.
Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The previous rtc-s3c had two issues related with its IRQ.

1. Users cannot open rtc multiple times because an open operation
   calls request_irq on the same IRQ.  (e.g., two user processes wants to
   open and read RTC time from rtc-s3c at the same time)

2. If alarm is set and no one has the rtc opened with filesystem
   (either the alarm is set by kernel/boot-loader or user set an alarm and
   closed rtc dev file), the pending bit is not cleared and no further
   interrupt is invoked.  When the alarm is used by the system itself such
   as a resume from suspend-to-RAM or other Low-power modes/idle, this is
   a critical issue.

This patch mitigates these issues by calling request_irq at probe and
free_irq at remove.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

RTC-S3C used to print out debug messages incorrectly.  This patch
corrects incorrect outputs.  (undecoded bcd numbers, incorrectly decoded
register values)

This patch affects the pr-debug messages only.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

bd2802_unregister_led_classdev() should unregister all registered
instances of led_classdev class that had registered by
bd2802_register_led_classdev().
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NKim Kyuwon <q1.kim@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following build errors:

  drivers/tty/serial/8250_early.c:160: error: 'BASE_BAUD' undeclared (first use in this function): 1 errors in 1 logs
  drivers/tty/serial/8250_early.c:37:24: error: asm/serial.h: No such file or directory: 1 errors in 1 logs

I am not sure if (1843200 / 16) is suitable for cris, but most other
arch's define it as this value.
Signed-off-by: NWANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since 43cc71ee ("platform: prefix MODALIAS with "platform:""), the
platform modalias is prefixed with "platform:".

This patch changes the MODULE_ALIAS to "platform:ab8500-pwm".
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NArun Murthy <arun.murthy@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make sure we are passing the same cookie in all calls to
request_threaded_irq() and free_irq().
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is an i2c driver, not a platform driver, thus use "i2c" prefix for
the module alias.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We need a callback to do some things after pwm_enable, pwm_disable
and pwm_config.
Signed-off-by: NDilan Lee <dilee@nvidia.com>
Reviewed-by: NRobert Morell <rmorell@nvidia.com>
Reviewed-by: NArun Murthy <arun.murthy@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 79dfdacc ("memcg: make oom_lock 0 and 1 based rather than
counter") tried to oom lock the hierarchy and roll back upon
encountering an already locked memcg.

The code is confused when it comes to detecting a locked memcg, though,
so it would fail and rollback after locking one memcg and encountering
an unlocked second one.

The result is that oom-locking hierarchies fails unconditionally and
that every oom killer invocation simply goes to sleep on the oom
waitqueue forever.  The tasks practically hang forever without anyone
intervening, possibly holding locks that trip up unrelated tasks, too.
Signed-off-by: NJohannes Weiner <jweiner@redhat.com>
Acked-by: NMichal Hocko <mhocko@suse.cz>
Acked-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>