rfcomm_cleanup_ttys() is also called from rfcomm_init(), so it can't
have __exit.
Reported-by: NMat Martineau <mathewm@codeaurora.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The bdaddr in the list root is completely unused and just
taking up space.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Tested-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Some features require knowing the DTIM period
before associating. This implements the ability
to wait for a beacon in mac80211 before assoc
to provide this value. It is optional since
most likely not all drivers will need this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For some drivers it can be useful to know whether the channel they're
supposed to switch to is going to be used for short off-channel work or
scanning, or whether the hardware is expected to stay on it for a while
longer. This is important for various kinds of calibration work, which
takes longer to complete and should keep some persistent state, even if
the channel temporarily changes.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts this commit. While in theory the change is
correct the patch does not address current assumptions made
by some drivers, one which is definitley affected is ath9k.

Prior to this change the scan complete callback would be
called after we returned to the home channel and configured
the hardware RX filters. After this change we call the scan
complete callback prior to both the hw config and the config
filter. At least for ath9k this breaks quite a few assumptions
on the callback, leading to disconnects to the AP after every scan
making the driver pretty useless on STA mode. The goal behind
this commit was to address the now understood spurious warnings
from ath9k and mac80211_hwsim on scanning on two wiphys at the
same time but we have now supressed these and will address this
issue in the next kernel release.

When fixing this for good next we must first review the other
driver's dependence on this logic and perhaps consider removal
of the scan complete callback all together.

Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In some cases there could be possible dereferencing freed pointer. The
update is intended to avoid this issue.
Signed-off-by: NYuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In case of errors during message composing msg should be freed after canceling.
Signed-off-by: NYuri Kululin <ext-yuri.kululin@nokia.com>
Signed-off-by: NYuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the function ieee80211_subif_start_xmit the logic related with
meshdrlen is under CONFIG_MAC80211_MESH macro, but in one place it isn't.
This is some update for this
Signed-off-by: NYuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Those annotation save memory and space on the binary. __init code is
discarded just after execute and __exit code is discarded if the module
is built into the kernel image or unload of modules is not allowed.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Testing first we avoid enter the loop when count = 0.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Certain headsets such as the Motorola H350 will reject SCO and eSCO
connection requests while the ACL is transitioning from sniff mode
to active mode. Add synchronization so that SCO and eSCO connection
requests will wait until the ACL has fully transitioned to active mode.

< HCI Command: Exit Sniff Mode (0x02|0x0004) plen 2
    handle 12
> HCI Event: Command Status (0x0f) plen 4
    Exit Sniff Mode (0x02|0x0004) status 0x00 ncmd 1
< HCI Command:  Setup Synchronous Connection (0x01|0x0028) plen 17
    handle 12 voice setting 0x0040
> HCI Event: Command Status (0x0f) plen 4
    Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
> HCI Event: Number of Completed Packets (0x13) plen 5
    handle 12 packets 1
> HCI Event: Mode Change (0x14) plen 6
    status 0x00 handle 12 mode 0x00 interval 0
    Mode: Active
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
    status 0x10 handle 14 bdaddr 00:1A:0E:50:28:A4 type SCO
    Error: Connection Accept Timeout Exceeded
Signed-off-by: NRon Shaffer <rshaffer@codeaurora.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Save a few bytes of text

(allyesconfig)
$ size drivers/net/wireless/built-in.o*
   text	   data	    bss	    dec	    hex	filename
3924568	 100548	 871056	4896172	 4ab5ac	drivers/net/wireless/built-in.o.new
3926520	 100548	 871464	4898532	 4abee4	drivers/net/wireless/built-in.o.old

$ size net/wireless/core.o*
   text	   data	    bss	    dec	    hex	filename
  12843	    216	   3768	  16827	   41bb	net/wireless/core.o.new
  12328	    216	   3656	  16200	   3f48	net/wireless/core.o
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Key locking simplification removed key->sdata != NULL verification from
ieee80211_key_free(). While that is fine for most use cases, there is one
path where this function can be called with an unlinked key (i.e.,
key->sdata == NULL && key->local == NULL). This results in a NULL pointer
dereference with the current implementation. This is known to happen at
least with FT protocol when wpa_supplicant tries to configure the key
before association.

Avoid the issue by passing in the local pointer to
ieee80211_key_free(). In addition, do not clear the key from hw_accel
or debugfs if it has not yet been added. At least the hw_accel one could
trigger another NULL pointer dereference.
Signed-off-by: NJouni Malinen <j@w1.fi>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In AP mode, there is no need to notify the driver about QoS
changes for the monitor interface that is created. The warning
in ieee80211_bss_info_change_notify() would be hit otherwise.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I just had the following:
WARNING: at drivers/net/wireless/iwlwifi/iwl-agn-tx.c:574 iwlagn_tx_skb+0x1576/0x15f0 [iwlagn]()
Call Trace:
 <IRQ>  [<ffffffff8105c5df>] warn_slowpath_common+0x7f/0xc0
 [<ffffffff8105c63a>] warn_slowpath_null+0x1a/0x20
 [<ffffffffa0290b46>] iwlagn_tx_skb+0x1576/0x15f0 [iwlagn]
 [<ffffffffa027076c>] iwl_mac_tx+0x5c/0x260 [iwlagn]
 [<ffffffffa01bdf5b>] __ieee80211_tx+0x10b/0x1a0 [mac80211]
 [<ffffffffa01bfb86>] ieee80211_tx_pending+0x186/0x2d0 [mac80211]
 [<ffffffff81062ea5>] tasklet_action+0x125/0x130
 [<ffffffff810634a6>] __do_softirq+0x106/0x270
 [<ffffffff8100c09c>] call_softirq+0x1c/0x30
iwlagn 0000:02:00.0: Attempting to modify non-existing station 107

Note that 107 == 0x6b which is slab poison.

The reason is that mac80211 passed a freed station
pointer to mac80211, because as it happened iwlwifi
reset itself while mac80211 was disconnecting from
the network.

It turns out that we do take care to look up the
station pointer in ieee80211_tx_pending_skb, but
then don't use it, which obviously is a bug. Fix
this by removing the ieee80211_tx_h_sta handler
and assigning the station pointer directly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When wireless extensions are used to control
an encrypted IBSS, we erroneously can try to
set the default management key. Fix this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Another remnant of the previous key locking scheme
needs to be removed -- this causes a warning
otherwise as ieee80211_set_default_mgmt_key will
acquire a mutex.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The "rd" variable isn't needed any more since 4f366c5d
"wireless: only use alpha2 regulatory information from country IE"
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The intent was to free "msp->ratelist" here.  "msp->sample_table" is
always NULL at this point.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"It's not problematic if minstrel gets feedback for rates that it
doesn't have in its list, it should just ignore it. - Felix"
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Cc: Felix Fietkau <nbd@openwrt.org>

If sta is NULL, we will have problems long before we get here...
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Cc: Felix Fietkau <nbd@openwrt.org>

IBSS has never had locking, instead relying on some
memory barriers etc. That's hard to get right, and
I think we had it wrong too until the previous patch.
Since this is not performance sensitive, it doesn't
make sense to have the maintenance overhead of that,
so add proper locking.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bob reported a lockdep complaint originating in
the mac80211 IBSS code due to the common work
struct patch. The reason is that the IBSS and
station mode code have different locking orders
for the cfg80211 wdev lock and the work struct
(where "locking" implies running/canceling).

Fix this by simply not canceling the work in
the IBSS code, it is not necessary since when
the REQ_RUN bit is cleared, the work will run
without effect if it runs. When the interface
is set down, it is flushed anyway, so there's
no concern about it running after memory has
been invalidated either.

This fixes
https://bugzilla.kernel.org/show_bug.cgi?id=16419

Additionally, looking into this I noticed that
there's a small window while the IBSS is torn
down in which the work may be rescheduled and
the REQ_RUN bit be set again after leave() has
cleared it when a scan finishes at exactly the
same time. Avoid that by setting the ssid_len
to zero before clearing REQ_RUN which signals
to the scan finish code that this interface is
not active.
Reported-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When WEP is not available, we should reject shared
key authentication because it could never succeed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

device_add() is called before adding the phy to the cfg80211 device
list.

So if a userspace program uses sysfs uevents to detect new phy
devices, and queries nl80211 to get phy info, it can get ENODEV even
though the phy exists in sysfs.

An easy workaround is to hold the cfg80211 mutex until the phy is
present in sysfs/cfg80211/debugfs.
Signed-off-by: NMaxime Bizon <mbizon@freebox.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change the enable_ertm param to disable_ertm and default value to 0. That
means that L2CAP Extended features are enabled by default now.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

memmory -> memory
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Implemented frame reassembly implementation for reassembling fragments
received from stream.
Signed-off-by: NSuraj Sumangala <suraj@atheros.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Modified packet based reassembly function hci_recv_fragment() to use
hci_reassembly()
Signed-off-by: NSuraj Sumangala <suraj@atheros.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Implements feature to reassemble received HCI frames from any input stream
Signed-off-by: NSuraj Sumangala <suraj@atheros.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Additional reassembly buffer to keep track of stream reasembly
Signed-off-by: NSuraj Sumangala <suraj@atheros.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We did some changes on the L2CAP configuration process and its behaviour
is bit different now. That justifies a updated on the L2CAP version.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Copyright for the time I worked on L2CAP during the Google Summer of Code
program.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Purely a cosmetic change, it doesn't change the code flow.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Probably a typo error. We were using the wrong struct to get size.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The extended L2CAP features requires that one should initiate a
ConfigReq after send the ConnectionRsp. This patch changes the behaviour
of the configuration process of our stack.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

L2CAP only deals with ACL links. EINVAL should be returned otherwise.
Signed-off-by: NJoão Paulo Rechi Vita <jprvita@profusion.mobi>
Acked-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Signed-off-by: NJoão Paulo Rechi Vita <jprvita@profusion.mobi>
Acked-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>