Currently, user gets priority map by implementing debugfs command
"echo dump qos pri map > cmd", this command will dump info in dmesg.
It's unnecessary and heavy.

To optimize it, create a single file "qos_pri_map" in tm directory
and use cat command to get info. It will return info to userspace,
rather than record in dmesg.

The display style is below:
$ cat qos_pri_map
vlan_to_pri: 0
PRI    TC
0       0
1       1
2       2
3       3
4       0
5       1
6       2
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, user gets pause config by implementing debugfs command
"echo dump qos pause cfg > cmd", this command will dump info in dmesg.
It's unnecessary and heavy.

To optimize it, create a single file "qos_pause_cfg" in tm directory
and use cat command to get info. It will return info to userspace,
rather than record in dmesg.

The display style is below:
$ cat qos_pause_cfg
pause_trans_gap: 0x7f
pause_trans_time: 0xffff
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, user gets tc schedule info by implementing debugfs command
"echo dump tc > cmd", this command will dump info in dmesg. It's
unnecessary and heavy.

To optimize it, create a single file "tc_sch_info" and use cat command
to get info. It will return info to userspace, rather than record in
dmesg.

The display style is below:
$ cat tc_sch_info
enabled tc number: 4
weight_offset: 14
TC    MODE  WEIGHT
0     dwrr     25
1     dwrr     25
2     dwrr     25
3     dwrr     25
4     dwrr      0
5     dwrr      0
6     dwrr      0
7     dwrr      0
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, user gets some tm info by implementing debugfs command
"echo dump tm > cmd", this command will dump info in dmesg. It's
unnecessary and heavy.

In addition, the info of this command mixes info of qset, priority,
pg and port. Qset and priority have their own command to get info of
themself, so can remove info of qset and priority from this command.

To optimize it, create two new files "tm_pg", "tm_port" in tm directory
and use cat command to separately get info of pg and port.

The display style is below:
$ cat tm_pg
ID  PRI_MAP  MODE DWRR  C_IR_B  C_IR_U  C_IR_S  C_BS_B  C_BS_S ...
00   0x1f    dwrr  1       75       9       0      31      20  ...

$ cat tm_port
IR_B  IR_U  IR_S  BS_B  BS_S  FLAG  RATE(Mbps)
75     9     0    31    20    1     200000
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for tm map is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"tm_map" for it, and query it by command "cat tm_map",
return the result to userspace, rather than record in dmesg.

As user can't specify queue id in cat command, driver will return info
of all queue id.

The display style is below:
$ cat tm_map
queue_id   qset_id   pri_id   tc_id
0000         0000      00       00
INDEX | TM BP QSET MAPPING:
0000  | 00000000:00000000:00000000:00000000:00000000:00000000:00000000
0256  | 00000000:00000000:00000000:00000000:00000000:00000002:00000000
0512  | 00000000:00000000:00000000:00000004:00000000:00000000:00000000
0768  | 00000000:00000008:00000000:00000000:00000000:00000000:00000000
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for fd tcam is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"fd_tcam" for it, and query it by command "cat fd_tcam",
return the result to userspace, rather than record in dmesg.

The display style is below:
$ cat fd_tcam
read result tcam key x(31):
00000000
00000000
00000000
08000000
00000600
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
read result tcam key y(31):
00000000
00000000
00000000
f7ff0000
0000f900
00000000
00000000
00000000
00000000
00000000
00000000
00000000
0000fff8
Signed-off-by: NHao Chen <chenhao288@hisilicon.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for queue info is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create two files
"rx_queue_info" and "tx_queue_info" for it, and query it
by command "cat rx_queue_info" and "cat tx_queue_info",
return the result to userspace, rather than record in dmesg.

The display style is below:
$ cat rx_queue_info
QUEUE_ID  BD_NUM  BD_LEN  TAIL  HEAD  FBDNUM  PKTNUM   ...
0           0       0     0     0       0       0      ...
1           0       0     0     0       0       0      ...
2           0       0     0     0       0       0      ...

$ cat tx_queue_info
QUEUE_ID  BD_NUM  TC  TAIL  HEAD  FBDNUM  OFFSET  PKTNUM  ...
0           0     0     0     0       0       0        0  ...
1           0     0     0     0       0       0        0  ...
2           0     0     0     0       0       0        0  ...
Signed-off-by: NHao Chen <chenhao288@hisilicon.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for queue map is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"queue_map" for it, and query it by command "cat queue_map",
return the result to userspace, rather than record in dmesg.

The display style is below:
$ cat queue_map
local_queue_id   global_queue_id   vector_id
0                0                 341
Signed-off-by: NHao Chen <chenhao288@hisilicon.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for reg dcb info is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"dcb" for it, and query it by command "cat dcb",
return the result to userspace, rather than record in dmesg.

The display style is below:
$ cat dcb
qset_id  roce_qset_mask  nic_qset_mask  qset_shaping_pass  qset_bp_status
0000           0x1            0x1             0x1               0x0
0001           0x1            0x1             0x1               0x0
0002           0x1            0x1             0x1               0x0
0003           0x1            0x1             0x1               0x0
0004           0x1            0x1             0x1               0x0
0005           0x1            0x1             0x1               0x0
0006           0x1            0x1             0x1               0x0
0007           0x1            0x1             0x1               0x0
pri_id  pri_mask  pri_cshaping_pass  pri_pshaping_pass
000       0x1           0x0                0x1
001       0x1           0x0                0x0
002       0x1           0x0                0x0
003       0x1           0x0                0x0
004       0x1           0x0                0x0
005       0x1           0x0                0x0
006       0x1           0x0                0x0
007       0x1           0x0                0x0
pg_id  pg_mask  pg_cshaping_pass  pg_pshaping_pass
000      0x1           0x0               0x1
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for reg is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create some files
"bios_common/ssu/igu_egu/rpu/ncsi/rtc/ppp/rcb/tqp/mac" for it,
and query it by command "cat xxx", return the result to
userspace, rather than record in dmesg.

The display style is below:
$ cat bios_common
BP_CPU_STATE: 0x0
DFX_MSIX_INFO_NIC_0: 0xc000
DFX_MSIX_INFO_NIC_1: 0x0
DFX_MSIX_INFO_NIC_2: 0x0
DFX_MSIX_INFO_NIC_3: 0x0
DFX_MSIX_INFO_ROC_0: 0xc000
DFX_MSIX_INFO_ROC_1: 0x0
DFX_MSIX_INFO_ROC_2: 0x0
DFX_MSIX_INFO_ROC_3: 0x0
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for ncl config is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"ncl_config" for it, and query it by command "cat ncl_config",
return the result to userspace, rather than record in dmesg.

The display style is below:
$cat ncl_config
offset | data
0x0000 | 0x00000028
0x0004 | 0x00000400
0x0008 | 0x08040201
0x000c | 0x00000000
0x0010 | 0x00040004
0x0014 | 0x00040004
0x0018 | 0x00000000
0x001c | 0x00000000
0x0020 | 0x00040004
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for m7 info is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"imp_info" for it, and query it by command "cat imp_info",
return the result to userspace, rather than record in dmesg.

The display style is below:
$cat imp_info
offset | data
0x0000 | 0x00000000  0x00000000
0x0008 | 0x00000000  0x00000000
0x0010 | 0x00000000  0x00000001
0x0018 | 0x00000000  0x00000000
0x0020 | 0x00000000  0x00000000
0x0028 | 0x00000000  0x00000000
0x0030 | 0x00000000  0x00000000
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for reset info is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"reset_info" for it, and query it by command "cat reset_info",
return the result to userspace, rather than record in dmesg.

The display style is below:
$cat reset_info
PF reset count: 0
FLR reset count: 0
GLOBAL reset count: 0
IMP reset count: 0
reset done count: 0
HW reset done count: 0
reset count: 0
reset fail count: 0
vector0 interrupt enable status: 0x1
reset interrupt source: 0x0
reset interrupt status: 0x0
RAS interrupt status:0x0
hardware reset status: 0x0
handshake status: 0x80
function reset status: 0x0

Change to the "hclge_show_rst_info" in the "hclge_reset_err_handle",
when the reset fails, display reset info immediately.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for intr is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"interrupt_info" for it, and query it by command "cat interrupt_info",
return the result to userspace, rather than record in dmesg.

The display style is below:
$cat interrupt_info
num_nic_msi: 65
num_roce_msi: 65
num_msi_used: 2
num_msi_left: 128
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for loopback is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"loopback" for it, and query it by command "cat loopback",
return the result to userspace, rather than record in dmesg.

The display style is below:
$ cat loopback
mac id: 0
app loopback: off
serdes serial loopback: off
serdes parallel loopback: off
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for mng tbl is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"mng_tbl" for it, and query it by command "cat mng_tbl",
return the result to userspace, rather than record in dmesg.

The display style is below:
$ cat mng_tbl
entry  mac_addr          mask  ether  mask  vlan  mask  i_map ...
00     00:00:00:00:00:00 0     88cc   0     0000  1     0f    ...
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for mac list info is implemented
by "echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create two files "uc" and
"mc" under directory "mac_list" for it, and query mac list info
by "cat mac_list/uc" and "mac_list/mc", return the result to
userspace, rather than record in dmesg.

The display style is below:
$ cat mac_list/uc
UC MAC_LIST:
FUNC_ID  MAC_ADDR            STATE
pf       00:18:2d:00:00:71   ACTIVE

$ cat mac_list/mc
MC MAC_LIST:
FUNC_ID  MAC_ADDR            STATE
pf       01:80:c2:00:00:21   ACTIVE
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for bd info is implemented
by "echo xxxx > cmd", and record the information in dmesg.
It's unnecessary and heavy.

To improve it, add two debugfs directories "tx_bd_info" and
"rx_bd_info", and create a file for each queue under these
two directories, and query the bd info of specific queue by
"cat tx_bd_info/tx_bd_queue*" or "cat rx_bd_info/rx_bd_queue*",
return the result to userspace, rather than record in dmesg.

The display style is below:
$ cat rx_bd_info/rx_bd_queue0
Queue 0 rx bd info:
BD_IDX   L234_INFO  PKT_LEN   SIZE...
0        0x0             60     60...
1        0x0           1512   1512...

$ cat tx_bd_info/tx_bd_queue0
Queue 0 tx bd info:
BD_IDX     ADDRESS  VLAN_TAG  SIZE...
0          0x0          0        0...
1          0x0          0        0...
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the debugfs command for dev capability and dev spec
are implemented by "echo xxxx > cmd", and record the information
in dmesg. It's unnecessary and heavy. To improve it, create a
single file "dev_info" for them, and query them by command
"cat dev_info", return the result to userspace, rather than
record in dmesg.

The display style is below:
$cat dev_info
dev capability:
support FD: yes
support GRO: yes
support FEC: yes
support UDP GSO: no
support PTP: no
support INT QL: no
support HW TX csum: no
support UDP tunnel csum: no
support TX push: no
support imp-controlled PHY: no
support rxd advanced layout: no

dev spec:
MAC entry num: 0
MNG entry num: 0
MAX non tso bd num: 8
RSS ind tbl size: 512
RSS key size: 40
RSS size: 1
Allocated RSS size: 0
Task queue pairs numbers: 1
RX buffer length: 2048
Desc num per TX queue: 1024
Desc num per RX queue: 1024
Total number of enabled TCs: 1
MAX INT QL: 0
MAX INT GL: 8160
MAX TM RATE: 100000
MAX QSET number: 1024
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, each debugfs command needs to create a file to get
the information. To better support more debugfs commands, the
debugfs process is reconstructed, including the process of
creating dentries and files, and obtaining information.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only when RXD advanced layout is enabled, in some cases
(e.g. ip fragments), the checksum of entire packet will be
calculated and filled in the least significant 16 bits of
the unused addr field.

So refactor out the handling of RX completion checksum: adjust
the location of the checksum in RX descriptor, and use ptype table
to identify whether this kind of checksum is calculated.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the driver gets packet type by parsing the
L3_ID/L4_ID/OL3_ID/OL4_ID from RX descriptor, it's
time-consuming.

Now some new devices support RXD advanced layout, which combines
previous OL3_ID/OL4_ID to 8bit ptype field, so the driver gets
packet type by looking up only one table, and L3_ID/L4_ID become
reserved fields.

Considering compatibility, the firmware will report capability of
RXD advanced layout, the driver will identify and enable it by
default. This patch provides basic function: identify and enable
the RXD advanced layout, and refactor out hns3_rx_checksum() by
using ptype table to handle RX checksum if supported.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If selftest and reset are performed at the same time, the phy
loopback setting may be still in enable state after the reset,
and device cannot link up. So fix this issue by disabling phy
loopback before phy_start().

Fixes: 256727da ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW error and global reset are reported through MSIX interrupts.
The same error may be reported to different functions at the
same time. When global reset begins, the pending reset request
set by this error is unnecessary. So clear the pending reset
request after the reset is complete to avoid the repeated reset.

Fixes: f6162d44 ("net: hns3: add handling of hw errors reported through MSIX")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, netif_tx_stop_all_queues() is used to ensure that
the xmit is not running, but for the concurrent case it will
not take effect, since netif_tx_stop_all_queues() just sets
a flag without locking to indicate that the xmit queue(s)
should not be run.

So use netif_tx_disable() to replace netif_tx_stop_all_queues(),
it takes the xmit queue lock while marking the queue stopped.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When skb->ip_summed is CHECKSUM_PARTIAL, for non-tunnel udp packet,
which has a dest port as the IANA assigned, the hardware is expected
to do the checksum offload, but the hardware whose version is below
V3 will not do the checksum offload when udp dest port is 4790.

So fixes it by doing the checksum in software for this case.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NHao Chen <chenhao288@hisilicon.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some cases, the device is not initialized because reset failed.
If another task calls hns3_reset_notify_up_enet() before reset
retry, it will cause an error since uninitialized pointer access.
So add check for HNS3_NIC_STATE_INITED before calling
hns3_nic_net_open() in hns3_reset_notify_up_enet().

Fixes: bb6b94a8 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The message sent to VF should be initialized, otherwise random
value of some contents may cause improper processing by the target.
So add a initialization to message in hclge_get_link_mode().

Fixes: 9194d18b ("net: hns3: fix the problem that the supported port is empty")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the UM, the type and enable status of igu_egu_hw_err
should be configured separately. Currently, the type field is
incorrect when disable this error. So fix it by configuring these
two fields separately.

Fixes: bf1faf94 ("net: hns3: Add enable and process hw errors from IGU, EGU and NCSI")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SEPARATOR_VALUE macro is used as separator when getting
the register value, but the value of this macro is different
between pf and vf, it is a bit confusing for the user, so
synchronize the value of vf with pf.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify some inappropriate spaces in comments of struct
hlcgevf_tqp_stats.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When enter suspend mode the counter of pf reset will be increased
twice, since both hclge_prepare_general() and hclge_prepare_wait()
increase this counter. So remove the duplicate counting in
hclge_prepare_general().
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To reduce the processing of unnecessary mailbox command when PF supports
actively push its link status to VFs, VFs stop sending request link
status command in periodic service task in this case.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, VF updates its link status every second by send query command
to PF in periodic service task. If link stats of PF is changed, VF may
need at most one second to update its link status.

To reduce delay of link status between PF and VFs, PF actively push its
link status to VFs when its link status is updated. And to let VF know
PF supports this new feature, the link status changed mailbox command
adds one bit to indicate it.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reset_prepare and reset_done calls have a null pointer check
on ae_dev however ae_dev is being dereferenced via the call to
ns3_is_phys_func with the ae->pdev argument. Fix this by performing
a null pointer check on ae_dev and hence short-circuiting the
dereference to ae_dev on the call to ns3_is_phys_func.

Addresses-Coverity: ("Dereference before null check")
Fixes: 715c58e9 ("net: hns3: add suspend and resume pm_ops")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some trivial spelling mistakes which caught my eye during the
review of the code.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Link: https://lore.kernel.org/r/20210409074223.32480-1-salil.mehta@huawei.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

To implement the system suspend/resume functions, the NIC driver needs
to support:
1. When the system enters the suspend mode, the driver needs to
implement the suspend callback function of the NIC device. The driver
needs to mute the device, stop all RX/TX activities of the device, and
unmap the interrupt.
2. When the system enters the resume mode, the driver needs to
implement the resume callback function of the NIC device and restore
the device to the state before suspension.

When the system enters the suspend and resume mode, the NIC driver
actually executes the PF function reset process.

When the PFs are suspending/resuming, VFs also enter the suspend/resume
state because the PFs trigger the VFs to reset, therefore no operation
is required when the VF pci_driver is suspending or resuming.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flr_prepare/flr_done functions are not only used in the FLR scenario,
but also used in the suspend/resume.

Change the function names to prepare_for_reset/rebuild_for_reset, change
the flr_prepare/flr_done to reset_prepare/reset_done in hnae3_ae_ops.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the VF down state bit is cleared after VF sending
link status request command. There is problem that when VF gets
link status replied from PF, the down state bit may still set
as 1. In this case, the link status replied from PF will be
ignored and always set VF link status to down.

To fix this problem, clear VF down state bit before VF requests
link status.

Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Limiting the scope of the variable vector_ring_chain to the block where it
is used.

Fixes: 424eb834 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>