A chip reset can occur after driver submits command to the stack. Abort
command processing if a chip reset has occurred or in progress when you
get a follow up for a command.
Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

If we fail to load one of the segments of firmware fail the operation
instead of trying to continue which will lead to a system crash since
the pointers to the next segment will not be updated correctly.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

For FA-WWPN capable device, ISP2031 and ISP27XX, when loop
dead is detected by a driver, restore WWPN from NVRAM.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Declaration error of mb array in qla2x00_iidma_fcport cause data
to be written beyond the array. This ends up causing stack corruption.
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Add support for the D-port (diagnostic port) fabric switch feature.

(Fabric Switch initiates loopback style port testing)
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Attempting to do any logins from the SCSI reset handler can lead to a deadlock
scenario if a rport times out and the FC transport layer.  Move doing any port
logins to the DPC thread so as not to impede the progress of the SCSI error
handler thread and avoid deadlock situations.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

For ISP27xx use the request/response queue index shadow registers
to avoid directly access them on the PCI bus.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Signed-off-by: NHiral Patel <hiral.patel@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Fixes some build warnings such as:
drivers/scsi/qla2xxx/qla_attr.c:162:6: warning: format '%lx' expects argument of
type 'long unsigned int', but argument 6 has type 'size_t'"
and
drivers/scsi/qla2xxx/qla_init.c:5198:7: warning: format '%lx' expects argument
of type 'long unsigned int', but argument 5 has type 'uint32_t' [-Wformat]
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Send aborts to the firmware via the request/response queue mechanism.
Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Fix interpreting the wrong IOCB type for task management
functions in the response path.
- Merge the task management function handling for various adapters.
Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If the execute firmware command fails we do not stop the rest of the
initialization process which will continue to fail so if we encounter an error
simply short circuit the process.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add the missing FCP statistics to sysfs.
Add reset FCP statistics functionality via sysfs.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

For supported ISPS, Read asic temperature by calling the
GET PARAMS (type C) mailbox command.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[jejb: checkpatch fixes]
Signed-off-by: NAtul Deshmukh <atul.deshmukh@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The patch changes a specifier used to output some variables. Instead of using
stack for each byte the '%*ph[CN]' allows to take a one pointer and prints
entire buffer as a hexadecimal string with the separator ':' or ''.
Signed-off-by: NOleksandr Khoshaba <Oleksandr.Khoshaba@gmail.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

At the end of qla2x00_configure_hba() we know that rval == QLA_SUCCESS.
Hence remove the dead code.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[jejb: fix up checkpatch issues]
Signed-off-by: NAndrew Vazquez <andrew.vasquez@qlogic.com>
Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

System crashes, in initiator mode operation, with
qla2xxx_copy_atioqueues() in stack trace when firmware dump is
attempted.

Check for atio_q_length alone does not indicate if atio_ring is
allocated, make explicit check of atio_ring to avoid the crash.

Applicable to ISP24xx, ISP25xx, ISP81xx & ISP83xx line of HBAs.
Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The original patch was not covering all the adapters and firmwares.

This commit reverts 3a11711a.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Give priority to I2C thermal.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Currently,the driver is processes RSCNs for each new NPIV ports that is created.
Processing the RSCN includes a name server query to see what has changed at the
name server side.  The name server query is performed by the physical port and
each virtual port on the physical adapter (since the RSCN is passed to each
virtual port for processing).  As the number of virtual ports being created
increases, this causes a lot of traffic and busies the firmware.

Processing the RSCN for a virtual port we already have a priori knowledge of is
not necessary so check the 24-bit fabric ID of the RSCN entry and skip
processing it if the RSCN is for a virtual port we already know about.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This reverts commit c0822b63.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This reverts commit 4dc77c36.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

BSG code path increments ref count in the send path, but does not
decrement in the return path leading to hang during unload of the
driver.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

To avoid continually doing ISP resets when get loop id fails to
obtain the adapter loop id, first try to do a link initialization.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Base the number of outstanding requests the driver will keep track of on the
available resources instead of being hard-coded.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>