UTMI+ Low Pin Interface (ULPI) is a commonly used PHY
interface for USB 2.0. The ULPI specification describes a
standard set of registers which the vendors can extend for
their specific needs. ULPI PHYs provide often functions
such as charger detection and ADP sensing and probing.

There are two major issues that the bus type is meant to
tackle:

Firstly, ULPI registers are accessed from the controller.
The bus provides convenient method for the controller
drivers to share that access with the actual PHY drivers.

Secondly, there are already platforms that assume ULPI PHYs
are runtime detected, such as many Intel Baytrail based
platforms. They do not provide any kind of hardware
description for the ULPI PHYs like separate ACPI device
object that could be used to enumerate a device from.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add MIPS Common Device Memory Map (CDMM) support in the form of a bus in
the standard Linux device model. Each device attached via CDMM is
discoverable via an 8-bit type identifier and may contain a number of
blocks of memory mapped registers in the CDMM region. IRQs are expected
to be handled separately.

Due to the per-cpu (per-VPE for MT cores) nature of the CDMM devices,
all the driver callbacks take place from workqueues which are run on the
right CPU for the device in question, so that the driver doesn't need to
be as concerned about which CPU it is running on. Callbacks also exist
for when CPUs are taken offline, so that any per-CPU resources used by
the driver can be disabled so they don't get forcefully migrated. CDMM
devices are created as children of the CPU device they are attached to.

Any existing CDMM configuration by the bootloader will be inherited,
however platforms wishing to enable CDMM should implement the weak
mips_cdmm_phys_base() function (see asm/cdmm.h) so that the bus driver
knows where it should put the CDMM region in the physical address space
if the bootloader hasn't already enabled it.

A mips_cdmm_early_probe() function is also provided to allow early boot
or particularly low level code to set up the CDMM region and probe for a
specific device type, for example early console or KGDB IO drivers for
the EJTAG Fast Debug Channel (FDC) CDMM device.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9599/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch adds support for advertising optional CPU features over udev
using the modalias, and for declaring compatibility with/dependency upon
such a feature in a module.

The mapping between feature numbers and actual features should be provided
by the architecture in a file called <asm/cpufeature.h> which exports the
following functions/macros:
- cpu_feature(FEAT), a preprocessor macro that maps token FEAT to a
  numeric index;
- bool cpu_have_feature(n), returning whether this CPU has support for
  feature #n;
- MAX_CPU_FEATURES, an upper bound for 'n' in the previous function.

The feature can then be enabled by setting CONFIG_GENERIC_CPU_AUTOPROBE
for the architecture.

For instance, a module that registers its module init function using

  module_cpu_feature_match(FEAT_X, module_init_function)

will be probed automatically when the CPU's support for the 'FEAT_X'
feature is advertised over udev, and will only allow the module to be
loaded by hand if the 'FEAT_X' feature is supported.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add RapidIO-specific modalias generation to enable udev notifications
about RapidIO-specific events.

The RapidIO modalias string format is shown below:

"rapidio:vNNNNdNNNNavNNNNadNNNN"

Where:
v  - Device Vendor ID (16 bit),
d  - Device ID (16 bit),
av - Assembly Vendor ID (16 bit),
ad - Assembly ID (16 bit),

as they are reported in corresponding Capability Registers (CARs)
of each RapidIO device.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

mei client bus will present some of the mei clients
as devices for other standard subsystems

Implement the probe, remove, match, device addtion routines, along with
the sysfs and uevent ones. mei_cl_device_id is also added to
mod_devicetable.h
A mei-cleint-bus.txt document describing the rationale and the API usage
is also added while ABI/testing/sysfs-bus-mei describeis the modalias ABI.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the target compiler to compute the offsets for the fields of the
device_id structures, so that it won't be broken by different alignments
between the host and target ABIs.

This also fixes missing endian corrections for some modaliases.
Signed-off-by: NAndreas Schwab <schwab@linux-m68k.org>
Signed-off-by: NMichal Marek <mmarek@suse.cz>