Ask for vbus_draw regulator before registering tranceiver to disallow possible
race between registration and set_power/etc.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Slightly reworked and cleaned up driver from Freescale LTIB
for MPC5121E. The driver has been ported to the current kernel,
proc interface "/proc/driver/fsl_usb2_otg" has been replaced by
sysfs interface.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Provide common otg_state_string() and use
it in drivers.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The twl4030-usb driver exports the status of VBUS as sysfs attribute.
In case an accessory charger adapter (ACA) is connected to the OTG
transceiver the attribute is always 'off', even when the charger
provides VBUS. Added a variable to keep track of the status of VBUS
and report it correctly
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@tomtom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix warning caused by stray semi-colon at end of macro:

drivers/usb/otg/twl6030-usb.c:183: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Hema HK <hemahk@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Add generic access ops for controllers with a ulpi viewport register
(e.g. Chipidea/ARC based controllers).
Signed-off-by: NBenoit Goby <benoit@android.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Direct access to PMIC register is not safe and will impact battery
charging. New IPC command supported in SCU FW for VBus power control.
USB OTG driver will switch to such commands instead of direct access
to PMIC register for safety and SCU FW will handle the actual work
after got the request(IPC command).

Due to this change, usb driver should wait more time for sync OTGSC
with USBCFG by SCU. Update wait time from 2ms to 5ms.
Signed-off-by: NHao Wu <hao.wu@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver is used across all MSM SoCs.  Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Update the last_event variable of otg_transceiver. This will be used in
the musb platform glue driver for runtime idling the device.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

most of our notifications, will be called from IRQ
context, so an atomic notifier suits the job better.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Save the last event in the otg_transceiver so that it can used in the
musb driver and gadget driver to configure the musb and enable the
vbus for host mode and OTG mode, if the device is connected during boot.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Introduce the twl6030_phy_suspend function and assign to otg.set_suspend
function pointer.
This function is used by the musb-omap2430 platform driver
during suspend/resume.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To get the ID status there was an I2C read transfer. Removed this I2C
read transfer as this info can be used from existing variable(linkstat).
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove the regulator enable while driver loading and enable it only when
the cable/device is connected and disable it when disconnected.

Remove the configuration of config_state and config_trans register
configuration as these registers are programmed when regulator
enable/disable is called.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The driver private data is retrieved incorrectly which results
a crash when written into "mode" debugfs file.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the below compiler warning

drivers/usb/otg/msm72k_otg.c:257: warning: 'msm_otg_suspend' defined but not used
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

after these changes omap1_defconfig and omap2plus_defconfig don't have any
section mismatches any more, making it plausible that the patches earlier
in this series are OK.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the below compilation errors.

  CC      drivers/usb/gadget/ci13xxx_msm.o
  CC      net/mac80211/led.o
  drivers/usb/gadget/ci13xxx_msm.c: In function 'ci13xxx_msm_notify_event':
  drivers/usb/gadget/ci13xxx_msm.c:42: error: 'USB_AHBBURST' undeclared (first use in this function)
  drivers/usb/gadget/ci13xxx_msm.c:42: error: (Each undeclared identifier is reported only once
  drivers/usb/gadget/ci13xxx_msm.c:42: error: for each function it appears in.)
  drivers/usb/gadget/ci13xxx_msm.c:43: error: 'USB_AHBMODE' undeclared (first use in this function)
make[4]: *** [drivers/usb/gadget/ci13xxx_msm.o] Error 1
make[3]: *** [drivers/usb/gadget] Error 2

MSM USB driver is not supported on boards like trout (MSM7201) which
has an external PHY.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds BLOCKING_INIT_NOTIFIER_HEAD in nop_usb_xceiv_probe,
so that we can avoid oops caused by uninitialized
nop->otg.notifier.rwsem which will be touched in otg_register_notifier
path.
Reported-by: NGupta, Ajay Kumar <ajay.gupta@ti.com>
Tested-by: NGupta, Ajay Kumar <ajay.gupta@ti.com>
Cc: Balbi, Felipe <balbi@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On a system with a USB3317 ULPI transceiver the following message
is shown on kernel boot:

ULPI transceiver vendor/product ID 0x0424/0x0006
Found SMSC USB3319 ULPI transceiver.
ULPI integrity check: passed.

The reason is that USB3317 has the same vendor/product ID as USB3319.

Make the ULPI ID generic for the USB331x transceivers.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

flush_scheduled_work() is being deprecated.  Directly flush or cancel
work items instead.

* u_ether, isp1301_omap, speedtch conversions are straight-forward.

* ochi-hcd should only flush when quirk_nec() is true as otherwise the
  work wouldn't have been initialized.

* In oti6858, cancel_delayed_work() + flush_scheduled_work() ->
  cancel_delayed_work_sync().
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: linux-usb@vger.kernel.org

Basic driver for ab8500 usb otg transceiver

TODO:
-Regulators support
-Host and OTG testing
-Interface with PRCMU
-Charging support
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Implement runtime and system pm ops to put hardware into low power
mode (LPM). As part of LPM, USB clocks are turned off, PHY is put
into suspend state and PHY comparators are turned off if VBUS/Id
notifications are not required from PHY.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver implements PHY initialization, clock management, ULPI IO ops
and simple OTG state machine to kick host/peripheral based on Id/VBUS
line status.  VBUS/Id lines are tied to a reference voltage on some boards.
Hence provide debugfs interface to select host/peripheral mode.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add the twl6030_usb transceiver file for compilation.
Signed-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Added the TWL6030-usb transceiver option in the Kconfig
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Adding the twl6030-usb transceiver support for OMAP4 musb driver.

OMAP4 supports 2 types of transceiver interface.

1. UTMI: The PHY is embedded within OMAP4. The transceiver functionality
is split between the twl6030 PMIC chip and OMAP4430. The VBUS, ID pin
sensing and OTG SRP generation part is integrated in TWL6030 and UTMI PHY
functionality is embedded within the OMAP4430.

There is no direct interactions between the MUSB controller and TWL6030
chip to communicate the session-valid, session-end and ID-GND events.
It has to be done through a software by setting/resetting bits in
one of the control module register of OMAP4430 which in turn toggles
the appropriate signals to MUSB controller.

The internal transceiver has functional clocks and
powerdown bits to powerdown the PHY for power saving.

Since there is no option available for having 2 transceiver drivers
for one USB controller, internal PHY specific APIs are passed through
plaform_data function pointers to use in the twl6030-usb transceiver
driver.

2. ULPI interface is provided for off-chip transceivers.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Function twl4030_usb_remove can cause unbalanced regulator disables in
twl4030_phy_power if the cable is not connected. Regulator enable/disable
calls are in balance only if the twl4030_phy_resume was called prior the
twl4030_usb_remove, that is, the cable was connected.

Fix this by checking the 'asleep' variable in twl4030_usb_remove since that
variable is used to check state in other functions.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

They should not be writable by any user.
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Hao Wu <hao.wu@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

use the new definitions on twl header for code
consistency.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Extend id's table to have ulpi phy names in it.
Report if the known phy is found.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Improve ulpi phy detection by utilizing the "scratch" register.
Allow unknown ulpi phy work without the need to hard-code the id.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For all modules, change <module>-objs to <module>-y; remove
if-statements and replace with lists using the kbuild idiom; move
flags to the top of the file; and fix alignment while trying to
maintain the original scheme in each file.

None of the dependencies are modified.
Signed-off-by: Nmatt mooney <mfm@muteddisk.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch updated Kconfig for langwell otg transceiver driver.
Add ipc driver(INTEL_SCU_IPC) as a dependency. Driver version is
updated too.
Signed-off-by: NHao Wu <hao.wu@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds support for the USB transceiver driver in the Langwell chipset used
on the Intel MID platforms. It folds up the original patch set which includes
basic support for the device, PHY low power mode (Please notice that there is
a limitation, after we drive VBus down, 2ms delay is required from SCU FW to
sync up OTGSC register with USBCFG register), software timers (the hardware
timers do not work in low power mode), HNP, SRP.
Signed-off-by: NHao Wu <hao.wu@intel.com>
Signed-off-by: NAlek Du <alek.du@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 461c3177(into 2.6.36-v3)
is put forward to power down phy if no usb cable is connected,
but does introduce the two issues below:

1), phy is not into work state if usb cable is connected
with PC during poweron, so musb device mode is not usable
in such case, follows the reasons:
	-twl4030_phy_resume is not called, so
		regulators are not enabled
		i2c access are not enabled
		usb mode not configurated

2), The kernel warings[1] of regulators 'unbalanced disables'
is caused if poweron without usb cable connected
with PC or b-device.

This patch fixes the two issues above:
	-power down phy only if no usb cable is connected with PC
and b-device
	-do phy initialization(via __twl4030_phy_resume) if usb cable
is connected with PC(vbus event) or another b-device(ID event) in
twl4030_usb_probe.

This patch also doesn't put VUSB3V1 LDO into active mode in
twl4030_usb_ldo_init until VBUS/ID change detected, so we can
save more power consumption than before.

This patch is verified OK on Beagle board either connected with
usb cable or not when poweron.

[1]. warnings of 'unbalanced disables' of regulators.
[root@OMAP3EVM /]# dmesg
------------[ cut here ]------------
WARNING: at drivers/regulator/core.c:1357 _regulator_disable+0x38/0x128()
unbalanced disables for VUSB1V8
Modules linked in:
Backtrace:
[<c0030c48>] (dump_backtrace+0x0/0x110) from [<c034f5a8>] (dump_stack+0x18/0x1c)
 r7:c78179d8 r6:c01ed6b8 r5:c0410822 r4:0000054d
[<c034f590>] (dump_stack+0x0/0x1c) from [<c0057da8>] (warn_slowpath_common+0x54/0x6c)
[<c0057d54>] (warn_slowpath_common+0x0/0x6c) from [<c0057e64>] (warn_slowpath_fmt+0x38/0x40)
 r9:00000000 r8:00000000 r7:c78e6608 r6:00000000 r5:fffffffb
 r4:c78e6c00
[<c0057e2c>] (warn_slowpath_fmt+0x0/0x40) from [<c01ed6b8>] (_regulator_disable+0x38/0x128)
 r3:c0410e53 r2:c0410ad5
[<c01ed680>] (_regulator_disable+0x0/0x128) from [<c01ed87c>] (regulator_disable+0x24/0x38)
 r7:c78e6608 r6:00000000 r5:c78e6c40 r4:c78e6c00
[<c01ed858>] (regulator_disable+0x0/0x38) from [<c02382dc>] (twl4030_phy_power+0x15c/0x17c)
 r5:c78595c0 r4:00000000
[<c0238180>] (twl4030_phy_power+0x0/0x17c) from [<c023831c>] (twl4030_phy_suspend+0x20/0x2c)
 r6:00000000 r5:c78595c0 r4:c78595c0
[<c02382fc>] (twl4030_phy_suspend+0x0/0x2c) from [<c0238638>] (twl4030_usb_irq+0x11c/0x16c)
 r5:c78595c0 r4:00000040
[<c023851c>] (twl4030_usb_irq+0x0/0x16c) from [<c034ec18>] (twl4030_usb_probe+0x2c4/0x32c)
 r6:00000000 r5:00000000 r4:c78595c0
[<c034e954>] (twl4030_usb_probe+0x0/0x32c) from [<c02152a0>] (platform_drv_probe+0x20/0x24)
 r7:00000000 r6:c047d49c r5:c78e6608 r4:c047d49c
[<c0215280>] (platform_drv_probe+0x0/0x24) from [<c0214244>] (driver_probe_device+0xd0/0x190)
[<c0214174>] (driver_probe_device+0x0/0x190) from [<c02143d4>] (__device_attach+0x44/0x48)
 r7:00000000 r6:c78e6608 r5:c78e6608 r4:c047d49c
[<c0214390>] (__device_attach+0x0/0x48) from [<c0213694>] (bus_for_each_drv+0x50/0x90)
 r5:c0214390 r4:00000000
[<c0213644>] (bus_for_each_drv+0x0/0x90) from [<c0214474>] (device_attach+0x70/0x94)
 r6:c78e663c r5:c78e6608 r4:c78e6608
[<c0214404>] (device_attach+0x0/0x94) from [<c02134fc>] (bus_probe_device+0x2c/0x48)
 r7:00000000 r6:00000002 r5:c78e6608 r4:c78e6600
[<c02134d0>] (bus_probe_device+0x0/0x48) from [<c0211e48>] (device_add+0x340/0x4b4)
[<c0211b08>] (device_add+0x0/0x4b4) from [<c021597c>] (platform_device_add+0x110/0x16c)
[<c021586c>] (platform_device_add+0x0/0x16c) from [<c0220cb0>] (add_numbered_child+0xd8/0x118)
 r7:00000000 r6:c045f15c r5:c78e6600 r4:00000000
[<c0220bd8>] (add_numbered_child+0x0/0x118) from [<c001c618>] (twl_probe+0x3a4/0x72c)
[<c001c274>] (twl_probe+0x0/0x72c) from [<c02601ac>] (i2c_device_probe+0x7c/0xa4)
[<c0260130>] (i2c_device_probe+0x0/0xa4) from [<c0214244>] (driver_probe_device+0xd0/0x190)
 r5:c7856e20 r4:c047c860
[<c0214174>] (driver_probe_device+0x0/0x190) from [<c02143d4>] (__device_attach+0x44/0x48)
 r7:c7856e04 r6:c7856e20 r5:c7856e20 r4:c047c860
[<c0214390>] (__device_attach+0x0/0x48) from [<c0213694>] (bus_for_each_drv+0x50/0x90)
 r5:c0214390 r4:00000000
[<c0213644>] (bus_for_each_drv+0x0/0x90) from [<c0214474>] (device_attach+0x70/0x94)
 r6:c7856e54 r5:c7856e20 r4:c7856e20
[<c0214404>] (device_attach+0x0/0x94) from [<c02134fc>] (bus_probe_device+0x2c/0x48)
 r7:c7856e04 r6:c78fd048 r5:c7856e20 r4:c7856e20
[<c02134d0>] (bus_probe_device+0x0/0x48) from [<c0211e48>] (device_add+0x340/0x4b4)
[<c0211b08>] (device_add+0x0/0x4b4) from [<c0211fd8>] (device_register+0x1c/0x20)
[<c0211fbc>] (device_register+0x0/0x20) from [<c0260aa8>] (i2c_new_device+0xec/0x150)
 r5:c7856e00 r4:c7856e20
[<c02609bc>] (i2c_new_device+0x0/0x150) from [<c0260dc0>] (i2c_register_adapter+0xa0/0x1c4)
 r7:00000000 r6:c78fd078 r5:c78fd048 r4:c781d5c0
[<c0260d20>] (i2c_register_adapter+0x0/0x1c4) from [<c0260f80>] (i2c_add_numbered_adapter+0x9c/0xb4)
 r7:00000a28 r6:c04600a8 r5:c78fd048 r4:00000000
[<c0260ee4>] (i2c_add_numbered_adapter+0x0/0xb4) from [<c034efa4>] (omap_i2c_probe+0x324/0x3e8)
 r5:00000000 r4:c78fd000
[<c034ec80>] (omap_i2c_probe+0x0/0x3e8) from [<c02152a0>] (platform_drv_probe+0x20/0x24)
[<c0215280>] (platform_drv_probe+0x0/0x24) from [<c0214244>] (driver_probe_device+0xd0/0x190)
[<c0214174>] (driver_probe_device+0x0/0x190) from [<c021436c>] (__driver_attach+0x68/0x8c)
 r7:c78b2140 r6:c047e214 r5:c04600e4 r4:c04600b0
[<c0214304>] (__driver_attach+0x0/0x8c) from [<c021399c>] (bus_for_each_dev+0x50/0x84)
 r7:c78b2140 r6:c047e214 r5:c0214304 r4:00000000
[<c021394c>] (bus_for_each_dev+0x0/0x84) from [<c0214068>] (driver_attach+0x20/0x28)
 r6:c047e214 r5:c047e214 r4:c00270d0
[<c0214048>] (driver_attach+0x0/0x28) from [<c0213274>] (bus_add_driver+0xa8/0x228)
[<c02131cc>] (bus_add_driver+0x0/0x228) from [<c02146a4>] (driver_register+0xb0/0x13c)
[<c02145f4>] (driver_register+0x0/0x13c) from [<c0215744>] (platform_driver_register+0x4c/0x60)
 r9:00000000 r8:c001f688 r7:00000013 r6:c005b6fc r5:c00083dc
r4:c00270d0
[<c02156f8>] (platform_driver_register+0x0/0x60) from [<c001f69c>] (omap_i2c_init_driver+0x14/0x1c)
[<c001f688>] (omap_i2c_init_driver+0x0/0x1c) from [<c002c460>] (do_one_initcall+0xd0/0x1a4)
[<c002c390>] (do_one_initcall+0x0/0x1a4) from [<c0008478>] (kernel_init+0x9c/0x154)
[<c00083dc>] (kernel_init+0x0/0x154) from [<c005b6fc>] (do_exit+0x0/0x688)
 r5:c00083dc r4:00000000
---[ end trace 1b75b31a2719ed1d ]---
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The reset state of twl4030-usb is not sleeping, it starts
up awaken and we need to disable it if we have booted
with a disconnected cable to avoid over consumption on
the default state.

To avoid problems later, we read the current state of the
transceiver from the PHY_PWR_CTRL register. The bootloader
can, anyways, put the device to sleep before us.

Tested on a custom OMAP board.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

1) Introduce ulpi specific flags for control of the ulpi phy
2) Extend the generic ulpi driver with support for Function and
Interface control of upli phy
3) Update the platforms using the generic ulpi driver with new ulpi
flags
4) Remove the otg control flags not in use
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>