Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg.  This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This is not needed anymore
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As part of the d0i3 removal.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

add support to print ldbg command in mvm and xvt mode
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support the new DBGC_SUSPEND_RESUME command to change the recording state.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If mvm->fwrt.cur_fw_img != IWL_UCODE_INIT, then
rfkill_safe_init_done must be true since
rfkill_safe_init_done is set to true before we start to load
the runtime image.
Remove the redundant condition.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We will soon be using a new notification that will be
initiated by the driver, sent to the firmware and sent
back to all the RSS queues by the firmware. This new
notification will be useful to synchronize the NSSN across
all the queues.

For now, don't send the notification, just add the code to
handle it. Later patch will add the code to actually send
it.

While at it, validate the baid coming from the firmware to
avoid accessing an array with a bad index in the driver.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Unite iwl_trans debug related fields under iwl_trans_debug struct to
increase readability and keep iwl_trans clean.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When a dump trigger is fired, the driver sets IWL_FWRT_STATUS_DUMPING and
aborts any consecutive dump collection.
To allow consecutive triggers firing, use 5 dump workers and allocate
them upon incoming dump collection requests.

This functionality is needed since in ini debug mode each trigger may
have entirely different memory regions to collect unlike the legacy
mode in which all the triggers dump the same memory regions.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we have a single image (same firmware image for INIT and
OPERATIONAL), we couldn't load the driver and register to the
stack if we had hardware RF-Kill asserted.

Fix this. This required a few changes:

1) Run the firmware as part of the INIT phase even if its
   ucode_type is not IWL_UCODE_INIT.
2) Send the commands that are sent to the unified image in
   INIT flow even in RF-Kill.
3) Don't ask the transport to stop the hardware upon RF-Kill
   interrupt if the RF-Kill is asserted.
4) Allow the RF-Kill interrupt to take us out of L1A so that
   the RF-Kill interrupt will be received by the host (to
   enable the radio).
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This debugfs file is really old, and cannot work properly since
the unified image support. Rather than trying to make it work,
which is difficult now due to multiple images (LMAC/UMAC etc.)
just remove it - we no longer need it since we properly do a FW
coredump even in D3 cases.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Allows to configure a periodic data collection
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If we fail to initialize because rfkill is enabled, then trying
to do debug collection currently just fails. Prevent that in the
high-level code, although we should probably also fix the lower
level code to do things more carefully.

It's not 100% clear that it fixes this commit, as the original
dump code at the time might've been more careful. In any case,
we don't really need to dump anything in this expected scenario.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Fixes: 71256480 ("iwlwifi: add fw dump upon RT ucode start failure")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Differentiate between SW and HW error interrupts and support ini HW
error trigger.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In restart flow, the driver requests HW restart from mac80211
and then mac80211 uses a worker to do the restart flow. In that flow a
sync dump is performed. Instead, schedule the dump worker before
requesting HW restart from mac80211. This approach simplifies the
restart flow.
Also, it is neeeded in order to differentiate between the handling of SW
and HW errors in a future commit.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Report all NO_DATA events to mac80211 so they get captured
in radiotap for usage in sniffer scenarios; map the info
type to a reasonable radiotap type for this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's no point in this, we already do everything in a nested
fashion, and if we didn't we'd already crash in iwl_mvm_leds_exit()
etc. Just remove the bit.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In case mac80211 was requested to perform an HW restart, but the HW
restart has not started yet, there is no need to request another one.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

AP interfaces still use some static TX queues (for probes,
broadcast and multicast frames). These queues were not stopped
correctly when the transport layer indicated the queue should be
stopped. As a result, when flushing the queues, new frames from
the overflow queue were tx'd, so the queues still had frames after
flushing. This ended up in an assert since trying to remove a station
with non-empty queues.

Fix it by stopping the static queues correctly when required.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

D3 debug data is disabled by default. Currently it is done by tampering
the dump mask. Add an operation that will allow this to be changed
without recompilation.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add new API and TLV for the ability to send commands in the beginning
and end of reset flow.

The full flow of recovery is:

1. While loading FW, get address (from the TLV) of target buffer
   to read in case of reset
2. If an error/assert happens read the address data from step 1.
3. Reset the HW and load the FW.
4. Send the data read in step 2.
5. Add station keys
6. Send notification to FW that reset flow is done.

The main use of the recovery flow is for support in PN/SN recovery
when offloaded
Signed-off-by: NMordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add support for FTM initiator, i.e. peer measurements with FTM
if the firmware supports FTM.

Additionally, add two defines we depend on in
include/linux/ieee80211.h.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add support for FTM responder for hardware/firmware combinations
that advertise support for it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Instead of having the command appear as "UNKNOWN" in the
dmesg, add the name to it.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There are several dumping flows in the driver in case of a fail
prior to operational.

In some cases we get 2 dumps while in others we get none.

Fix this by uniting the different flows.
Add a different dump type to driver triggered dumps in case we want
a dump but did not got assert, and make all dumping go through
iwl_fw_dbg_collect_desc to avoid multiple dumps.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Remove duplicated include.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There are two cases that can cause the alive flow to fail,
an assert or a timeout.
Currently we mask any incoming asserts when we wait for alive.

Solve this by differentiating between the two cases:
1. Let the regular error handling to handle a received assert
2. Do a dump collection in the case of a timeout
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: f38efdb2 ("iwlwifi: add dump collection in case alive flow fails")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we do channel switch, we used to schedule time events
ourselves. This was offloaded to FW. Support the new command
and flow.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Implement CSI (channel estimation matrix) reporting in the mvm
driver, if the firmware has the capability.

Currently only a debugfs API is provided as the API is still
under discussion.

For now, RX aggregation must be disabled to use this feature
on data frames as we haven't found a good way to attach the
data to A-MPDUs, given complexities with multi-queue.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add the location/time-of-flight/FTM APIs that we'll use in
follow-up patches to implement FTM responder and initiator.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This is an ancient (~2015) implementation that no longer matches
the firmware in any way, and most likely never worked. Remove all
of it so it can be reintroduced properly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Clean up the LDBG config command to not be called "continuous
recording", and while at it actually remove the continuous
recording implementation completely since it was only used for
store & forward architectures.

This also fixes a bug at least in iwl_fw_dbg_buffer_allocation()
because what's now "__le32 type" (matching the firmware) used to
be "__le16 enable_recording", so the buffer allocation config
sub-struct would erroneously have started at the wrong offset.
In the other cases this didn't actually lead to a bug as other
bytes in pad[] were all zeroes, so accessing the 16-bit value as
a 32-bit value wouldn't make a difference (in little endian.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Move to use the new mac80211 TXQs implementation. This has
quite a few benefits for us. We can get rid of the awkward
mapping of DQA to mac80211 queues. We can stop buffering
traffic while waiting for the queue to be allocated. We can
also use mac80211 AMSDUs instead of building it ourselves.

The usage is pretty simple:
Each ieee80211_txq contains iwl_mvm_txq. There is such a
queue for each TID, and one for management frames. We keep
having static AP queues for probes and non-bufferable MMPDUs,
along with broadcast and multicast queues. Those are being
used from the "old" TX invocation path - iwl_mvm_mac_tx.

When there is a new frame in a TXQ, iwl_mvm_mac_wake_tx is
being called, and either invokes the TX path, or allocates
the queue if it does not exist.

Most of the TX path is left untouched, although we can consider
cleaning it up some more, for example get rid of the duplication
of txq_id in both iwl_mvm_txq and iwl_mvm_dqa_txq_info.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Handle RX no data notification, which is used for advertising NDP to
radiotap.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently opmode is limited to asking transport to either
dump all the dumps configured at startup, or monitor only.
Instead, pass to transport a bitmask, to allow flexibility.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If the driver is unloaded when D3 debug data pulling is enabled
but not triggered, it doesn't release the data buffer.

Fix this by adding iwl_fw_runtime_free and calling it from the
relevant places.

Fixes: 2d8c2615 ("iwlwifi: add d3 debug data support")
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The trigger structure is being passed around, when
all we care about is whether to dump only monitor
or not. Pass a bool instead.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>