We can simply use conf_is_ht() check where needed.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch enables mac80211 to send a null frame and also to
check for tim in the beacon if dynamic power save is enabled.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

a) hw_config() should not be called from siwpower() for the drivers which do not support
   dynamic powersave.
b) IEEE80211_HW_NO_STACK_DYNAMIC_PS needs to be verified in set_associated() also before
   enabling the power save timers.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As TKIP is not updated to new security needs which arise when
TKIP is used to encrypt A-MPDU aggregated data frames, IEEE802.11n
does not allow any cipher other than CCMP (Which has new extensions
defined) as pairwise cipher between HT peers.

When such configuration (TKIP/WEP in HT) is forced, we still
associate in non-HT mode (11a/b/g).
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wlan0: switched to short barker preamble (BSSID=00:01:aa:bb:cc:dd)
wlan0: switched to short slot (BSSID=) <something is missing here>

should be:

wlan0: switched to short barker preamble (BSSID=00:01:aa:bb:cc:dd)
wlan0: switched to short slot (BSSID=00:01:aa:bb:cc:dd)
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch implements dynamic power save for mac80211. Basically it
means enabling power save mode after an idle period. Implementing it
dynamically gives a good compromise of low power consumption and low
latency. Some hardware have support for this in firmware, but some
require the host to do it.

The dynamic power save is implemented by adding an timeout to
ieee80211_subif_start_xmit(). The timeout can be enabled from userspace
with Wireless Extensions. For example, the command below enables the
dynamic power save and sets the time timeout to 500 ms:

iwconfig wlan0 power timeout 500m

Power save now only works with devices which handle power save in firmware.
It's also disabled by default and the heuristics when and how to enable is
considered as a policy decision and will be left for the userspace to handle.
In case the firmware has support for this, drivers can disable this feature
with IEEE80211_HW_NO_STACK_DYNAMIC_PS.

Big thanks to Johannes Berg for the help with the design and code.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also disable power save when disassociated. It makes no sense to have
power save enabled while disassociated.

iwlwifi seems to have this check in the driver, but it's better to do this
in mac80211 instead.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a typo in ieee80211_send_assoc(), net/mac80211/mlme.c.

The error is usage of a wrong member when building
the ie80211 management frame (it should be assoc_req, and not reassoc_req).
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds option for HT-enabled drivers to report HT rates
(HT20/HT40, short GI, MCS index) to mac80211. These rates are
currently not in the rate table, so the rate_idx is used to indicate
MCS index.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

HT management is done differently for AP and STA modes, unify
to just the ->config() callback since HT is fundamentally a
PHY property and cannot be per-BSS.

Rename enum nl80211_sec_chan_offset as nl80211_channel_type to denote
the channel type ( NO_HT, HT20, HT40+, HT40- ).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes unneeded member (skbuff) from
ieee80211_ibss_add_sta() method in its declaration (in ieee80211_i.h)
and its callers (in rx.c and mlme.c)

This patch removes unneeded member from struct ieee80211_rx_data
in ieee80211_i.h.

(Originally posted as two patches. -- JWL)
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some access points (e.g. Sitecom WL-174) use an empty string as hidden SSID.
Signed-off-by: NFabio Rossi <rossi.f@inwind.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch reorders calls during disassociation in
ieee80211_set_disassoc function.
Since sta_info_unlink calls sta_notify(REMOVE) it will
remove the station representing AP from the driver before
it has disassociated from it using bss_info_changed callback.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a disassoc packet is received from the AP with a reason code of
'leaving the BSS', mac80211 should go into DISABLED state just as it
would do if the AP suddenly went away for some reason, as that is what
will happen shortly after the AP leaves anyway.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds country IE parsing to mac80211 and enables its usage
within the new regulatory infrastructure in cfg80211. We parse
the country IEs only on management beacons for the BSSID you are
associated to and disregard the IEs when the country and environment
(indoor, outdoor, any) matches the already processed country IE.

To avoid following misinformed or outdated APs we build and use
a regulatory domain out of the intersection between what the AP
provides us on the country IE and what CRDA is aware is allowed
on the same country.

A secondary device is allowed to follow only the same country IE
as it make no sense for two devices on a system to be in two
different countries.

In the case the AP is using country IEs for an incorrect country
the user may help compliance further by setting the regulatory
domain before or after the IE is parsed and in that case another
intersection will be performed.

CONFIG_WIRELESS_OLD_REGULATORY is supported but requires CRDA
present.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes unnecessary #include <linux/netdevice.h> from
/net/mac80211/mlme.c.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Before ieee80211_notify_mac() was added, it was presented with the
use case of using it to tell mac80211 that the association may
have been lost because the firmware crashed/reset.

Since then, it has also been used by iwlwifi to (slightly) speed
up re-association after resume, a workaround around the fact that
mac80211 has no suspend/resume handling yet. It is also not used
by any other drivers, so clearly it cannot be necessary for "good
enough" suspend/resume.

Unfortunately, the callback suffers from a severe problem: It only
works for station mode. If suspend/resume happens while in IBSS or
any other mode (but station), then the callback is pointless.

Recently, it has created a number of locking issues, first because
it required rtnl locking rather than RCU due to calling sleeping
functions within the critical section, and now because it's called
by iwlwifi from the mac80211 workqueue that may not use the rtnl
because it is flushed under rtnl.
(cf. http://bugzilla.kernel.org/show_bug.cgi?id=12046)

I think, therefore, that we should take a step back, remove it
entirely for now and add the small feature it provided properly.
For suspend and resume we will need to introduce new hooks, and for
the case where the firmware was reset the driver will probably
simply just pretend it has done a suspend/resume cycle to get
mac80211 to reprogram the hardware completely, not just try to
connect to the current AP again in station mode. When doing so, we
will need to take into account locking issues and possibly defer
to schedule_work from within mac80211 for the resume operation,
while the suspend operation must be done directly.

Proper suspend/resume should also not necessarily try to reconnect
to the current AP, the time spent in suspend may have been short
enough to not be disconnected from the AP, mac80211 will detect
that the AP went out of range quickly if it did, and if the
association is lost then the AP will disassoc as soon as a data
frame is sent. We might also take into account WWOL then, and
have mac80211 program the hardware into such a mode where it is
available and requested.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ieee80211_notify_mac() function uses ieee80211_sta_req_auth() which
in turn calls ieee80211_set_disassoc() which calls a few functions that
need to be able to sleep, so ieee80211_notify_mac() cannot use RCU
locking for the interface list and must use rtnl locking instead.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In previous code all the rates were marked as basic.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the SSID from the driver API since now there is no
driver that requires knowing the SSID and I think it's
unlikely that any hardware design that does require the
SSID will play well with mac80211.

This also removes support for setting the SSID in master
mode which will require a patch to hostapd to not try.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch prints reason code for deauth/dissoc frames to give users
more ideas what's happened for the disconnection.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch add a check on the return value of dev_alloc_skb() in
ieee80211_sta_join_ibss() in net/mac80211/mlme.c.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We never clearly defined the semantics of the sta_notify callback
and it was originally posted for iwlwifi which still doesn't use
it at all. With the recent HT rework ath9k started relying on it,
but I made a mistake there in that I made ath9k assume the HT
information has already been filled in at sta_notify time. This
isn't a hard thing to do, so do it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I noticed that when for some reason [1] the probe or auth times
out, wpa_supplicant doesn't realise this and only tries the next
AP when it runs into its own timeout, which is ten seconds, and
that's quite long. Fix this by making mac80211 notify userspace
that it didn't associate.

[1] my wrt350n in mixed B/G/HT mode often runs into this, maybe
it's because one of the antennas is broken off and for whatever
reason it decides to use that antenna to transmit the response
frames (auth, probe); I do see beacons fine so it's not totally
broken. Works fine in pure-G mode.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The HT handling has the following deficiencies, which I've
(partially) fixed:
 * it always uses the AP info even if there is no AP,
   hence has no chance of working as an AP
 * it pretends to be HW config, but really is per-BSS
 * channel sanity checking is left to the drivers
 * it generally lets the driver control too much

HT enabling is still wrong with this patch if you have more than
one virtual STA mode interface, but that never happens currently.
Once WDS, IBSS or AP/VLAN gets HT capabilities, it will also be
wrong, see the comment in ieee80211_enable_ht().

Additionally, this fixes a number of bugs:
 * mac80211: ieee80211_set_disassoc doesn't notify the driver any
             more since the refactoring
 * iwl-agn-rs: always uses the HT capabilities from the wrong stuff
               mac80211 gives it rather than the actual peer STA
 * ath9k: a number of bugs resulting from the broken HT API

I'm not entirely happy with putting the HT capabilities into
struct ieee80211_sta as restricted to our own HT TX capabilities,
but I see no cleaner solution for now.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move bss_conf into the vif struct so that drivers can
access it during ->tx without having to store it in
the private data or similar. No driver updates because
this is only for when they want to start using it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up a number of things:
 * the unusable definition of the HT capabilities/HT information
   information elements
 * variable names that are hard to understand
 * mac80211: move ieee80211_handle_ht to ht.c and remove the unused
             enable_ht parameter
 * mac80211: fix bug with MCS rate 32 in ieee80211_handle_ht
 * mac80211: fix bug with casting the result of ieee80211_bss_get_ie
             to an information element _contents_ rather than the
             whole element, add size checking (another out-of-bounds
             access bug fixed!)
 * mac80211: remove some unused return values in favour of BUG_ON
             checking
 * a few minor other things
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch makes mac80211 handle short slot requests from the AP
properly. Also warn about uses of IEEE80211_CONF_SHORT_SLOT_TIME
and optimise out the code since it cannot ever be hit anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also remove a few stray DECLARE_MAC_BUF that were no longer
used at all.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's no checking that the HT IEs are of the right length
which can be used by an attacker to cause an out-of-bounds
access by sending a too short HT information/capability IE.
Fix it by simply pretending those IEs didn't exist when too
short.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The association response IEs are sent to userland with an IWEVCUSTOM
event, which unfortunately is limited to a little more than 100 bytes
of IE information with the encoding used.  Many APs send so much
IE information that this message overflows.  When the IWEVCUSTOM
event is too large, the kernel doesn't send it to userland anyway --
better just not to send it.

An attempt was made by Jouni Malinen to correct this issue by
converting to use IWEVASSOCREQIE and IWEVASSOCRESPIE messages instead
("mac80211: Use IWEVASSOCREQIE instead of IWEVCUSTOM").  Unfortunately,
that caused a problem due to 32-/64-bit interactions on some systems and
was reverted after the 'userland ABI' rule was invoked.  That leaves
us with this option instead of a proper fix, at least until we move
to a cfg80211-based solution.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Restore revert "mac80211: Use IWEVASSOCREQIE instead of IWEVCUSTOM",
originally reverted in commit bf7394cc.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the led behavior in IBSS. After we joined an IBSS cell we
need to inform the led that we got associated. Although there is no 802.11
association in IBSS mode, the semantic of "There is a link" is relevant.
This allows the led to blink in IBSS mode (at least this solves a bug for
iwlwifi).
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While associated, we should probe with the SSID we're associated to,
not the scan SSID.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Long awaited, hard work. This patch totally cleans up the rate control
API to remove the requirement to include internal headers outside of
net/mac80211/.

There's one internal use in the PID algorithm left for mesh networking,
we'll have to figure out a way to clean that one up and decide how to
do the peer link evaluation, possibly independent of the rate control
algorithm or via new API.

Additionally, ath9k is left using the cross-inclusion hack for now, we
will add new API where necessary to make this work properly, but right
now I'm not expert enough to do it. It's still off better than before.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rate control algorithms may need access to a station's
HT capabilities, so share the ht_info struct in the
public station API.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As more preparation for a saner rate control algorithm API,
share the supported rates bitmap in the public API.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch changes mac80211 to share some more data about
stations with drivers. Should help iwlwifi and ath9k when
 they get around to updating, and might also help with
implementing rate control algorithms without internals.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers need to know the basic rateset to be able to configure
the ACK/CTS programming in hardware correctly.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>