Set the defaults on probe for the packet buffer size registers for the
i210.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We can't know what PHY is to be used for i354 backplane, so use MAC
loopback for ethtool tests.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The name igb_ptp_enable is not synonymous with the purpose of this
function, so rename it to better explain its purpose.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We don't need this header file, so we shouldn't be including it.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In cases where the driver is loaded while there are no SFP+ modules in
the cage the interface was not being detected as SFP capable. To account
for this the driver called identify_sfp in ixgbe_get_settings to make
sure the data is correct. However when there is no SFP+ module in the cage
the driver waits for the I2C reads to time out which can take more than a
second and will cause issues with tools (like net-snmp) that may poll
for that information.

This patch resolves the issue by identifying interfaces with no PHY
type set as SFP capable which allows the driver to detect the SFP module
when the interface is brought up. As result of this we can also remove the
identify_sfp call from ixgbe_get_settings.

v2: remove the 82599 specific check since we have 82598 devices that are SFP
capable.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/resource_size.cocci
Signed-off-by: NBenoit Taine <benoit.taine@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the hix5hd2 XGMAC 1Gb ethernet device.
The controller requires two queues for tx and two queues for rx.
Controller fetch buffer from free queue and then push to used queue.
Diver should prepare free queue and free buffer from used queue.
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ETHTOOL_{G,S}RXFHINDIR and ETHTOOL_{G,S}RSSH should work for drivers
regardless of whether they expose the hash key, unless you try to
set a hash key for a driver that doesn't expose it.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 5bbde4d2 ("net: fec: use pinctrl PM helpers") caused the following
build error on m68k:

drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_open':
drivers/net/ethernet/freescale/fec_main.c:1819:2: error: implicit declaration of function 'pinctrl_pm_select_default_state' [-Werror=implicit-function-declaration]
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_close':
drivers/net/ethernet/freescale/fec_main.c:1863:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]

In order to fix the build error, include the linux/pinctrl/consumer.h header
file.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.

Verified by compilation only.

The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
    when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a jiffies hack we can use the standard api for delays.
Signed-off-by: NManuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.

Verified by compilation only.

The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
    when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.

Verified by compilation only.

The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
    when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To fix:

  CC      drivers/net/ethernet/broadcom/bcmsysport.o
In file included from drivers/net/ethernet/broadcom/bcmsysport.c:28:0:
drivers/net/ethernet/broadcom/bcmsysport.h:41:8: error: redefinition of 'struct tsb'
arch/sparc/include/asm/mmu_64.h:65:8: note: originally defined here
make[1]: *** [drivers/net/ethernet/broadcom/bcmsysport.o] Error 1

we change struct tsb to struct bcm_tsb in the broadcom driver in
order to avoid the namespace collision.  For consistency, we also
change struct rsb to struct bcm_rsb, so the Rx/Tx symmetry is
maintained.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The buffers for the TSO headers belong to a DMA coherent region which is
allocated at ndo_open() time, and released at ndo_stop() time.

Therefore, and contrary to the TSO payload descriptor buffers, the TSO header
buffers don't need to be unmapped. This commit adds a check to detect a
TSO header buffer and explicitly prevent the unmap.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After adding proper stop/wake thresholds, we can expect a queue to never
be full and drop the NETDEV_TX_BUSY return path. In any case, if the queue
cannot accommodate a TSO packet, the packet would be discarded.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.

In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit fixes the current dropped packet count by doing it properly,
increasing the count when a packet is discarded; i.e. the packet is not
processed and the driver returns NETDEV_TX_OK.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The buffers for the TSO headers belong to a DMA coherent region which is
allocated at ndo_open() time, and released at ndo_stop() time.

Therefore, and contrary to the TSO payload descriptor buffers, the TSO header
buffers don't need to be unmapped. This commit adds a check to detect a
TSO header buffer and explicitly prevent the unmap.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This is true only for the last fragment of the packet.

This is wrong, however, since every descriptor buffer is DMA mapped and needs
to be unmapped.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.

In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver has no need for a custom NAPI weigth. Use the default
one, which has the same value.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add netpoll support to macvlan devices. Based on the netpoll support in the 802.1q vlan code.

Tested and macvlan could work well with netconsole.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The min_tx_pkt variable decides the cutoff point where the driver
will stop padding out NTBs to maximum size. The padding is a tradeoff
where we use some USB bus bandwidth to allow the device to receive
fixed size buffers. Different devices will have different optimal
settings, spanning from no padding at all to padding every NTB.
There is no way to automatically figure out which setting is best
for a specific device.

The default value is a reasonable tradeoff, calculated based on the
USB packet size and out NTB max size. This may have to be changed
along with any tx_max changes.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mandatory GetNtbParameters control request is an important part of
the host <-> device protocol negotiation in CDC NCM (and CDC MBIM). It
gives device limits which the host must obey when configuring the
protocol aggregation variables. The driver will enforce this by
rejecting attempts to set any of the tunable variables to a value
which is not supported by the device.  Exporting the parameter block
helps userspace decide which values are allowed without resorting
to trial and error.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool coalesce API is not applicable for this driver. Forcing
it to fit the NCM aggregation redefined the API in a driver specific
way, which is much worse than defining a clean new API. These ethtool
coalesce functions have therefore been replaced by a new sysfs API.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Attach a driver specific sysfs group to the netdev, and use it
for the rx/tx aggregation variables.

The datagram aggregation defined by the CDC NCM specification is
specific to this device class (including CDC MBIM). Using the
ethtool interrupt coalesce API as an interface to the aggregation
parameters redefined that API in a driver specific and confusing
way.  A sysfs group
 - makes it clear that this is a driver specific userspace API, and
 - allows us to export the real values instead of some translated
   version, and
 - lets us include more aggregation variables which were impossible
   to force into the ethtool API.

Additionally, using sysfs allows tuning the driver on space
constrained hosts where userspace tools like ethtool are undesired.
Suggested-by: NPeter Stuge <peter@stuge.se>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It doesn't matter whether the buffer size goes up or down.  We have to
keep usbnet and device syncronized to be able to split transfers at the
correct boundaries. The spec allow skipping short packets when using
max sized transfers.  If we don't tell usbnet about our new expected rx
buffer size, then it will merge and/or split NTBs.  The driver does not
support this, and the result will be lots of framing errors.

Fix by always reallocating usbnet rx buffers when the rx_max value
changes.

Fixes: 68864abf ("net: cdc_ncm: support rx_max/tx_max updates when running")
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are calling usbnet_start_xmit() to flush any remaining data,
depending on the side effect that tx_curr_skb is set to NULL,
ensuring a new allocation using the updated tx_max.  But this
side effect will only happen if there were any cached data ready
to transmit. If not, then an empty tx_curr_skb is still allocated
using the old tx_max size. Free it to avoid a buffer overrun.

Fixes: 68864abf ("net: cdc_ncm: support rx_max/tx_max updates when running")
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cloning the big skbs we use for USB buffering chokes up TCP and
SCTP because the socket memory limits are hitting earlier than
they should. It is better to unconditionally copy the unwrapped
packets to freshly allocated skbs.
Reported-by: NJim Baxter <jim_baxter@mentor.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macvlan dev should always have the same mac address like lowerdev
when in the passthru mode, change the mac address alone will break the
work mechanism, so when the lowerdev or macvlan mac address changes,
we should propagate the changes to another dev.

v1->v2: Allow macvlan dev to change mac address for passthru mode and propagate to
	lowerdev.

v2->v3: Don't set the mac address to the lower dev's unicast address for
	passthru mode when mac address changes.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following patch moved device tree interrupt resolution into
platform_get_irq_byname:

  ad69674e of/irq: do irq resolution in platform_get_irq_byname()

As a result, the function no longer only return -ENXIO on error.
This breaks DT based probing of stmmac, as seen in test runs of
linux-next next-20140526 cubie2-sunxi_defconfig:

  http://lists.linaro.org/pipermail/kernel-build-reports/2014-May/003659.html

This patch makes the stmmac_platform probe function properly handle
error codes, such as returning for deferred probing, and other codes
returned by of_irq_get_by_name.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ideally, we would need to generate IP ID using a per destination IP
generator.

linux kernels used inet_peer cache for this purpose, but this had a huge
cost on servers disabling MTU discovery.

1) each inet_peer struct consumes 192 bytes

2) inetpeer cache uses a binary tree of inet_peer structs,
   with a nominal size of ~66000 elements under load.

3) lookups in this tree are hitting a lot of cache lines, as tree depth
   is about 20.

4) If server deals with many tcp flows, we have a high probability of
   not finding the inet_peer, allocating a fresh one, inserting it in
   the tree with same initial ip_id_count, (cf secure_ip_id())

5) We garbage collect inet_peer aggressively.

IP ID generation do not have to be 'perfect'

Goal is trying to avoid duplicates in a short period of time,
so that reassembly units have a chance to complete reassembly of
fragments belonging to one message before receiving other fragments
with a recycled ID.

We simply use an array of generators, and a Jenkin hash using the dst IP
as a key.

ipv6_select_ident() is put back into net/ipv6/ip6_output.c where it
belongs (it is only used from this file)

secure_ip_id() and secure_ipv6_id() no longer are needed.

Rename ip_select_ident_more() to ip_select_ident_segs() to avoid
unnecessary decrement/increment of the number of segments.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change updates the enic driver to make use of __dev_uc_sync and
__dev_mc_sync calls.  Previously the driver was doing its own list
management by storing the mc_addr and uc_addr list in a 32 address array.
With this change the sync data is stored in the netdev_addr_list structures
and instead we just track how many addresses we have written to the device.
When we encounter 32 we stop and print a message as occurred previously with
the old approach.

Other than the core change the only other bit needed was to propagate the
constant attribute with the MAC address as there were several spots where
is twas only passed as a u8 * instead of a const u8 *.

This patch is meant to maintain the original functionality without the use
of the mc_addr and uc_addr arrays.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following patch removed unnecessary spin_lock/unlock calls
in ethtool_ops callback functions. In the second and final version
of the patch one spin_lock call was left behind.

commit cab6715c
Author: Yang Wei <Wei.Yang@windriver.com>
Date:   Sun May 25 09:53:44 2014 +0800

    net: driver: stmicro: Remove some useless the lock protection

This introduced the following sparse warning:

drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c:424:1: warning:
	context imbalance in 'stmmac_get_pauseparam' -
	different lock contexts for basic block
Signed-off-by: NEmil Goode <emilgoode@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 70a640d0.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We shouldn't be using regulator_get_optional() here. These
regulators are always present as part of the physical design and
there isn't any way to use an internal regulator or change the
source of the reference voltage via software. Given that the only
users of this driver in the kernel are DT based, this change
should be transparent to them even if they don't specify any
supplies because the regulator framework will insert dummy
supplies as needed.

Cc: Nishanth Menon <nm@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 70a640d0
("net/mlx4_en: Use affinity hint") and commit
c8865b64 ("cpumask: Utility function
to set n'th cpu - local cpu first") because these changes break
the build when SMP is disabled amongst other things.
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We shouldn't be using regulator_get_optional() here. These
regulators are always present as part of the physical design and
there isn't any way to use an internal regulator or change the
source of the reference voltage via software. Given that the only
users of this driver in the kernel are DT based, this change
should be transparent to them even if they don't specify any
supplies because the regulator framework will insert dummy
supplies as needed.

Cc: Nishanth Menon <nm@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.

We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it.  To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores.  If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.
Signed-off-by: NYuval Atias <yuvala@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>