Dynamically allocate the CPUFreq frequency table on OMAP2xxx chips.
This fixes some compilation problems, since the kernel may not know
what chip it is running on until boot-time.  This also reduces the size
of the CPUFreq frequency table.

Problem originally reported by Felipe Balbi <felipe.balbi@nokia.com>.
Thanks also for comments on the patch from Felipe and Kevin.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

A subsequent patch adds code on OMAP2xxx to dynamically allocate the
CPUFreq frequency table in clk_init_cpufreq_table(), so for it to
avoid a leak, it will need a corresponding function to free the
memory.  This patch adds clk_exit_cpufreq_table() with generic
code to call a chip-specific variant inside the clockfw_lock spinlock via
struct clk_functions.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Revise some of the comments in the OMAP2xxx OPP data for clarity.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>

if we enable CPUFREQ we can't build omap2 for two reasons,
one of them is fixed by the patch below.

It's failing because the __must_be_array() check in
ARRAY_SIZE() is failing and printing the following message:

arch/arm/mach-omap2/clock2xxx.c:453: error: negative width in bit-field '<anonymous>'
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
[paul@pwsan.com: commit message updated; changed rate variable name]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Commit 52650505 added an __initdata
decoration to the structure containing the clk_enable and clk_disable
functions.  Once init data was freed, these pointers went to null, and
the next enable or disable call caused the kernel to crash.  This
change removes this decoration.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
[paul@pwsan.com: patch manually split and commit message edited]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

This change adds in some missing clocks that were needed as a result
of 526505... (OMAP1 clock: convert mach-omap1/clock.h to
mach-omap1/clock_data.c).  Prior to this, it was just assumed that
these clocks existed for all devices, and it was used directly instead
of calling it out with a clock_get call or similar.  So, not having
the CK_7XX meant these clocks weren't being used anymore for omap 7xx
devices, which broke things badly.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
[paul@pwsan.com: commit message edited]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The only symbols that should be exported are symbols that are to be
called from loadable kernel modules, e.g., device drivers.  In the
context of plat-omap/clock.c, these should only be the Linux clock
interface symbols as defined by include/linux/clk.h.  Core code
doesn't need these symbols to be exported.  Also, clean up an old
comment while here.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add necessary definitions to clock framework to allow changing
dpll4_m5_ck rate.  This is used by the camera code.
Signed-off-by: NJouni Högander <jouni.hogander@nokia.com>
Signed-off-by: NTuukka Toivonen <tuukka.o.toivonen@nokia.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The correct parent of the McBSP 2, 3, and 4 functional clocks is
PER_96M_FCLK, not CORE_96M_FCLK.  Fix this in the OMAP clock tree.
Reported by Nicole Chalhoub <n-chalhoub@ti.com>.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Nicole Chalhoub <n-chalhoub@ti.com>

UART1 & 2 were missing clockdomains resulting in broken omap_hwmod
init for these devices.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Commit 10db25fe causes the following
kernel messages during N800 boot (and presumably all other 2420
boards):

[    0.000000] BUG: mapping for 0x58000000 at 0xe0000000 overlaps vmalloc space
[    0.000000] BUG: mapping for 0x59000000 at 0xe1000000 overlaps vmalloc space
[    0.000000] BUG: mapping for 0x5a000000 at 0xe2000000 overlaps vmalloc space

Fix by remapping the IVA memory areas somewhere outside vmalloc space.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Out of the three major OMAP2 chip types, OMAP2420, OMAP2430, and OMAP3430,
we only map the IVA on OMAP2420.  The memory mapping is not shared between
OMAP2420 and OMAP2430, so it is inappropriate to label those macros as
'24XX'; this patch changes them to '2420'.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

In OMAP2/3 some of the clock-domains which did not have control
facility were being falsely written to and read using the CM_CLKSTCTRL
register though it did not exist for them. One check is added to remove
this flaw.
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>

Remove duplicated #include('s) in
  arch/arm/mach-omap2/clock34xx.c
  arch/arm/mach-omap2/io.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Without this the kernel doesn't boot, it craches in
omap_mux_package_fixup(), since the package_subset becomes NULL.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise bringing up new boards can be harder:

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
last sysfs file:
Modules linked in:
CPU: 0    Not tainted  (2.6.33-rc2-00015-g0bc9c93-dirty #37)
PC is at omap_mux_init+0xa4/0x3d8
LR is at omap_mux_init+0x3c/0x3d8
...
Signed-off-by: NTony Lindgren <tony@atomide.com>

`!' has a higher precedence than `&' so parentheses are required.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

not(!) has a higher precedence than bit and(&).
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Keys: 'right arrow', 'up arrow' and 'select' were mapped
wrongly. This patch corrects them.
This patch also adds one missing key present in the board,
currently I added it as 'unknown' key, as I am not able to
find proper description for this key.
One key entry (r: 7, c: 5) is present in the keymap, which
is really not present in the board, removing it.
Signed-off-by: NVimal Singh <vimalsingh@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit f62349ee makes it possible to
have some other than first uart port as ttyS0, which breaks the workaround
serial_in_override() function which will try to address the first uart
port (for ttyS0) and not the one that was initialized.
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
CC: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 9905a43b made struct backlight_ops const. Omap was
setting check_fb dynamically, which caused the following
compile error:

drivers/video/backlight/omap1_bl.c: In function 'omapbl_probe':
drivers/video/backlight/omap1_bl.c:142: error: assignment of read-only variable 'omapbl_ops'

Turns out pdata->check_fb is not being used, so just remove
it to fix the compile.

Cc: Emese Revfy <re.emese@gmail.com>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 35c9049b added
drivers/spi/omap_spi_100k.c.

This patch add the related clocks and pin muxing
entries to make the driver work on omap7xx platforms.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Flags is not used on 15xx.
Signed-off-by: NTony Lindgren <tony@atomide.com>

obj can't be both NULL and be an error pointer.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Some chips, namely any OMAP1 chips using METHOD_MPUIO,
OMAP15xx and OMAP7xx, cannot be setup to respond to on-chip GPIO
interrupts in both rising and falling edge directions -- they can
only respond to one direction or the other, depending on how the
ICR is configured.

Additionally, current code forces rising edge detection if both
flags are specified:

        if (trigger & IRQ_TYPE_EDGE_RISING)
                l |= 1 << gpio;
        else if (trigger & IRQ_TYPE_EDGE_FALLING)
                l &= ~(1 << gpio);
        else
                goto bad;

This change implements a toggle function that will modify the ICR
to flip the direction of interrupt for IRQs that are requested with
both rising and falling flags.  The toggle function is not called
for chips and GPIOs it does not apply to through the use of a flip_mask
that's added on a per-bank basis.  The mask is only set for those
GPIOs where a toggle is necessary.  Edge detection starts out the
same as above with FALLING mode first.

The toggle happens on EACH interrupt; without it, we have the
following sequence of actions on GPIO transition:

  ICR    GPIO               Result
  0x1    0 -> 1 (rising)    Interrupt
  0x1    1 -> 0 (falling)   No interrupt

  (set ICR to 0x0 manually)
  0x0    0 -> 1 (rising)    No interrupt
  0x0    1 -> 0 (falling)   Interrupt

That is, with the ICR set to 1 for a gpio, only rising edge interrupts
are caught, and with it set to 0, only falling edge interrupts are
caught.  If we add in the toggle, we get this:

  ICR    GPIO               Result
  0x1    0 -> 1 (rising)    Interrupt (ICR set to 0x0)
  0x0    1 -> 0 (falling)   Interrupt (ICR set to 0x1)
  0x1    0 -> 1 ...

so, both rising and falling are caught, per the request for both
(IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING).
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In its current form, the omap_mcbsp_request() function can return after
irq_request() failure without any cleanups, effectively locking out the port
forever with clocks left running. Fix it.
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This reverts commit ae1b22f6.

As Linus said in 982d007a: "There was something really messy about
cmpxchg8b and clone CPU's, so if you enable it on other CPUs later, do it
carefully."

This breaks lguest for those configs, but we can fix that by emulating
if we have to.

Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14884Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For chips like Niagara2 that have true overflow indications
in the %pcr (which we don't actually need and don't use)
the interrupt signal persists until the overflow bits are
cleared by an explicit %pcr write.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If perf events are active, we should not reset the %pcr to
PCR_PIC_PRIV.  That perf events code does the management.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Since the files have identical content, might as well simplify.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This has the adverse effect of converting many 29bit configs to 32bit
mode, while this is a change that needs to be done manually for each
platform. Turn it off by default in order to cut down on spurious bug
reports.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

While the PMB is available on SH-4A parts, SH4AL-DSP parts exclude it
altogether. As such, explicitly disable PMB support for these parts. If
this changes in the future for newer subtypes, this will have to be made
more fine-grained.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Pass the frame pointer from the regs of the interrupted path
to dump_trace() while processing the stack trace.

Currently, dump_trace() takes the current bp and starts the
callchain from dump_trace() itself. This is wasteful because
we need to walk through the entire NMI/DEBUG stack before
retrieving the interrupted point.

We can fix that by just using the frame pointer from the
captured regs. It points exactly where we want to start.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1262235183-5320-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>

Introduce kernel parameter acpi_sleep=sci_force_enable

some laptop requires SCI_EN being set directly on resume,
or else they hung somewhere in the resume code path.

We already have a blacklist for these laptops but we still need
this option, especially when debugging some suspend/resume problems,
in case there are systems that need this workaround and are not yet
in the blacklist.
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>

The wrong address was being used to write the SCIR led regs on remote
hubs.  Also, there was an inconsistency between how BIOS and the kernel
indexed these regs.  Standardize on using the lower 6 bits of the APIC
ID as the index.

This patch fixes the problem of writing to an errant address to a
cpu # >= 64.
Signed-off-by: NMike Travis <travis@sgi.com>
Reviewed-by: NJack Steiner <steiner@sgi.com>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The wrong address was being used to write the SCIR led regs on
remote hubs.  Also, there was an inconsistency between how BIOS
and the kernel indexed these regs.  Standardize on using the
lower 6 bits of the APIC ID as the index.

This patch fixes the problem of writing to an errant address to
a cpu # >= 64.
Signed-off-by: NMike Travis <travis@sgi.com>
Reviewed-by: NJack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@kernel.org
LKML-Reference: <4B3922F9.3060905@sgi.com>
[ v2: fix a number of annoying checkpatch artifacts and whitespace noise ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>

As CPUs are migrated over to more fully-featured clock frameworks of
their own and off of the legacy CPG code, they no longer have any real
need for defining the PCLK value. The PCLK define in itself is already
fairly misleading, as many boards get their input clocks from different
sources, making this value fairly arbitrary anyways.

Outside of the legacy CPG clock framework, the only place where this
value is used is for deriving CLOCK_TICK_RATE, which we set back to the
legacy PIT value that it was before the PCLK definitions were added in
the first place.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

As suggested by Vegard Nossum, use KERN_WARNING for error
reporting to make sure kmemcheck reports end up in syslog.
Suggested-by: NVegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1261990935.4641.7.camel@penberg-laptop>
Signed-off-by: NIngo Molnar <mingo@elte.hu>