When memory is limited (on kdump kernel), reduce size of rx and tx rings.
Also reduce the number of rx rings.
Signed-off-by: NAlaa Hleihel <alaa@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now, both Rx and Tx confirmation frames handled during
NAPI poll were counted toward the NAPI budget. However, Tx
confirmations are lighter to process than Rx frames, which can
skew the amount of work actually done inside one NAPI cycle.

Update the code to only count Rx frames toward the NAPI budget
and set a separate threshold on how many Tx conf frames can be
processed in one poll cycle.

The NAPI poll routine stops when either the budget is consumed
by Rx frames or when Tx confirmation frames reach this threshold.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/mscc/ocelot_board.c: In function 'mscc_ocelot_probe':
drivers/net/ethernet/mscc/ocelot_board.c:262:17: warning:
 variable 'phy_mode' set but not used [-Wunused-but-set-variable]
   enum phy_mode phy_mode;

It never used since introduction in
commit 71e32a20 ("net: mscc: ocelot: make use of SerDes PHYs for handling their configuration")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with
the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and
can set the blinking pattern of each of its 4 LEDs, supports SyncE as
well as HP Auto-MDIX detection.

This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC,
WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4
LEDs.

The VSC8574 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.

The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.

If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.

Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with the
MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set
the blinking pattern of each of its 4 LEDs, supports hardware offloading
of MACsec and supports SyncE as well as HP Auto-MDIX detection.

This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC,
downshifting, HP Auto-MDIX detection and blinking pattern for its 4
LEDs.

The VSC8584 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.

The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.

If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.

Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.

The revA of the VSC8584 PHY (which is not and will not be publicly
released) should NOT patch the firmware of the microcontroller or it'll
make things worse, the easiest way is just to not support it.
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Here, the rc variable is either used only for the condition right after
the assignment or right before being used as the return value of the
function it's being used in.

So let's remove this unneeded temporary variable whenever possible.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

`if (x != 0)` is basically a more verbose version of `if (x)` so let's
use the latter so it's consistent throughout the whole driver.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The == operator precedes the || operator, so we can remove the
parenthesis around (a == b) || (c == d).

The condition is rather explicit and short so removing the parenthesis
definitely does not make it harder to read.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Microsemi PHYs (VSC 8530/31/40/41) need to update the Energy Efficient
Ethernet initialization sequence.
In order to avoid certain link state errors that could result in link
drops and packet loss, the physical coding sublayer (PCS) must be
updated with settings related to EEE in order to improve performance.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRaju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are a few counters available in the PHY: receive errors, false
carriers, link disconnects, media CRC errors and valids counters.

So let's expose those in the PHY driver.

Use the priv structure as the next PHY to be supported has a few
additional counters.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRaju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Microsemi PHYs have multiple banks of registers (called pages).
Registers can only be accessed from one page, if we need a register from
another page, we need to switch the page and the registers of all other
pages are not accessible anymore.

Basically, to read register 5 from page 0, 1, 2, etc., you do the same
phy_read(phydev, 5); but you need to set the desired page beforehand.

In order to guarantee that two concurrent functions do not change the
page, we need to do some locking per page. This can be achieved with the
use of phy_select_page and phy_restore_page functions but phy_write/read
calls in-between those two functions shall be replaced by their
lock-free alternative __phy_write/read.

Let's migrate this driver to those functions.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to fix and improve dpaa2-ptp driver
in some places.

- Fixed the return for some functions.
- Replaced kzalloc with devm_kzalloc.
- Removed dev_set_drvdata(dev, NULL).
- Made ptp_dpaa2_caps const.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to removed unused code for dprtc.
This code will be re-added along with more features
of dpaa2-ptp added.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In dpaa2-ptp driver, it's odd to use rtc in names of
some functions and structures except these dprtc APIs.
This patch is to use ptp instead of rtc in names.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NETDEVICES dependency and ETHERNET dependency hadn't
been required since dpaa2-eth was moved out of staging.
Also allowed COMPILE_TEST for dpaa2-eth.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to move DPAA2 PTP driver out of staging/
since the dpaa2-eth had been moved out.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mark instructions that use pointers to areas in the stack outside of the
current stack frame, and process them accordingly in mem_op_stack().
This way, we also support BPF-to-BPF calls where the caller passes a
pointer to data in its own stack frame to the callee (typically, when
the caller passes an address to one of its local variables located in
the stack, as an argument).

Thanks to Jakub and Jiong for figuring out how to deal with this case,
I just had to turn their email discussion into this patch.
Suggested-by: NJiong Wang <jiong.wang@netronome.com>
Suggested-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJiong Wang <jiong.wang@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

When pre-processing the instructions, it is trivial to detect what
subprograms are using R6, R7, R8 or R9 as destination registers. If a
subprogram uses none of those, then we do not need to jump to the
subroutines dedicated to saving and restoring callee-saved registers in
its prologue and epilogue.

This patch introduces detection of callee-saved registers in subprograms
and prevents the JIT from adding calls to those subroutines whenever we
can: we save some instructions in the translated program, and some time
at runtime on BPF-to-BPF calls and returns.

If no subprogram needs to save those registers, we can avoid appending
the subroutines at the end of the program.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

On performing a BPF-to-BPF call, we first jump to a subroutine that
pushes callee-saved registers (R6~R9) to the stack, and from there we
goes to the start of the callee next. In order to do so, the caller must
pass to the subroutine the address of the NFP instruction to jump to at
the end of that subroutine. This cannot be reliably implemented when
translated the caller, as we do not always know the start offset of the
callee yet.

This patch implement the required fixup step for passing the start
offset in the callee via the register used by the subroutine to hold its
return address.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Relocation for targets of BPF-to-BPF calls are required at the end of
translation. Update the nfp_fixup_branches() function in that regard.

When checking that the last instruction of each bloc is a branch, we
must account for the length of the instructions required to pop the
return address from the stack.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NJiong Wang <jiong.wang@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Offloaded programs using BPF-to-BPF calls use the stack to store the
return address when calling into a subprogram. Callees also need some
space to save eBPF registers R6 to R9. And contrarily to kernel
verifier, we align stack frames on 64 bytes (and not 32). Account for
all this when checking the stack size limit before JIT-ing the program.
This means we have to recompute maximum stack usage for the program, we
cannot get the value from the kernel.

In addition to adapting the checks on stack usage, move them to the
finalize() callback, now that we have it and because such checks are
part of the verification step rather than translation.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

This is the main patch for the logics of BPF-to-BPF calls in the nfp
driver.

The functions called on BPF_JUMP | BPF_CALL and BPF_JUMP | BPF_EXIT were
used to call helpers and exit from the program, respectively; make them
usable for calling into, or returning from, a BPF subprogram as well.

For all calls, push the return address as well as the callee-saved
registers (R6 to R9) to the stack, and pop them upon returning from the
calls. In order to limit the overhead in terms of instruction number,
this is done through dedicated subroutines. Jumping to the callee
actually consists in jumping to the subroutine, that "returns" to the
callee: this will require some fixup for passing the address in a later
patch. Similarly, returning consists in jumping to the subroutine, which
pops registers and then return directly to the caller (but no fixup is
needed here).

Return to the caller is performed with the RTN instruction newly added
to the JIT.

For the few steps where we need to know what subprogram an instruction
belongs to, the struct nfp_insn_meta is extended with a new subprog_idx
field.

Note that checks on the available stack size, to take into account the
additional requirements associated to BPF-to-BPF calls (storing R6-R9
and return addresses), are added in a later patch.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NJiong Wang <jiong.wang@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Similarly to "exit" or "helper call" instructions, BPF-to-BPF calls will
require additional processing before translation starts, in order to
record and mark jump destinations.

We also mark the instructions where each subprogram begins. This will be
used in a following commit to determine where to add prologues for
subprograms.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJiong Wang <jiong.wang@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

The checks related to eBPF helper calls are performed each time the nfp
driver meets a BPF_JUMP | BPF_CALL instruction. However, these checks
are not relevant for BPF-to-BPF call (same instruction code, different
value in source register), so just skip the checks for such calls.

While at it, rename the function that runs those checks to make it clear
they apply to _helper_ calls only.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJiong Wang <jiong.wang@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

In order to support BPF-to-BPF calls in offloaded programs, the nfp
driver must collect information about the distinct subprograms: namely,
the number of subprograms composing the complete program and the stack
depth of those subprograms. The latter in particular is non-trivial to
collect, so we copy those elements from the kernel verifier via the
newly added post-verification hook. The struct nfp_prog is extended to
store this information. Stack depths are stored in an array of dedicated
structs.

Subprogram start indexes are not collected. Instead, meta instructions
associated to the start of a subprogram will be marked with a flag in a
later patch.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJiong Wang <jiong.wang@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

In preparation for support for BPF to BPF calls in offloaded programs,
rename the "stack_depth" field of the struct nfp_prog as
"stack_frame_depth". This is to make it clear that the field refers to
the maximum size of the current stack frame (as opposed to the maximum
size of the whole stack memory).
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

In preparation for BPF-to-BPF calls in offloaded programs, add a new
function attribute to the struct bpf_prog_offload_ops so that drivers
supporting eBPF offload can hook at the end of program verification, and
potentially extract information collected by the verifier.

Implement a minimal callback (returning 0) in the drivers providing the
structs, namely netdevsim and nfp.

This will be useful in the nfp driver, in later commits, to extract the
number of subprograms as well as the stack depth for those subprograms.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJiong Wang <jiong.wang@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

There is no need to compare *val.vu32* with < 0 because
such variable is of type u32 (32 bits, unsigned), making it
impossible to hold a negative value. Fix this by removing
such comparison.

Also, initialize variable *max_val* to -1, just in case
it is not initialized to either BNXT_MSIX_VEC_MAX or
BNXT_MSIX_VEC_MIN_MAX before using it in a comparison
with val.vu32 at line 159:

	if (val.vu32 > max_val)

Addresses-Coverity-ID: 1473915 ("Unsigned compared against 0")
Addresses-Coverity-ID: 1473920 ("Uninitialized scalar variable")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As preparation for new trigger type, make iwl_fw_dbg_collect_desc
agnostic to the trigger structure.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

iwl_fw_dbg_collect can be called by any function that already
has the error string ready. iwl_fw_dbg_collect_trig, on the
other hand, does string formatting. The occurrences decrement
is at iwl_fw_dbg_collect_trig, instead of iwl_fw_dbg_collect,
which causes it to sometimes be skipped. Move it to the right
location.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NYisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As preparation for new trigger format, make the function
agnostic to the trigger fomat. Instead it gets the relevant
parameters - id and delay.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For trigger-based PPDUs, most values aren't part of the HE-SIG-A
because they're preconfigured by the trigger frame. However, we
still have this information since we used the trigger frame to
configure the hardware, so we can (and do) read it back out and
can thus show it in radiotap.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When the info type is MU, we still have the data from the TSF
overload words, so should decode that. When it's MU_EXT_INFO
we additionally have the SIG-B common 0/1/2 fields.

Also document the validity depending on the info type and fix
the name of the regular TB PPDU info type accordingly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add debugfs to send host command in mvm and fmac op modes.
Allows to send host command at runtime via send_hcmd debugfs file.
The command is received as a string that represents hex values.

The struct of the command is as follows:
[cmd_id][flags][length][data]
cmd_id and flags are 8 chars long each.
length is 4 chars long.
data is length * 2 chars long.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add send host command op to firmware runtime op struct to allow sending
host commands to the op mode from the fw runtime context.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Bump the firmware API version to 41.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Change MCC update response API to be compatible with new FW API.
While at it change v2 which is not in use anymore to v3 and cleanup
mcc_update v1 command and response which is obsolete.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If we use the iwl_pcie_txq_build_tfd() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The fall-through to the MVM case is intended as we have to do
*something* to continue, and can't easily clean up. So we'll
just fail in mvm later, if this does happen.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>