Let drivers advertise support for station-mode SAE authentication
offload with a new NL80211_EXT_FEATURE_SAE_OFFLOAD flag.
Signed-off-by: NChung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add definition of WPA version 3 for SAE authentication.
Signed-off-by: NChung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add NL80211_ATTR_IFINDEX attribute to port authorized event to indicate
the operating interface of the device. Also put NL80211_ATTR_WIPHY
attribute in it to be consistent with the other MLME notifications.
Signed-off-by: NChung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

IEEE 802.11 - 2016 forbids mixing MPDUs with different keyIDs in one
A-MPDU. Drivers supporting A-MPDUs and Extended Key ID must actively
enforce that requirement due to the available two unicast keyIDs.

Allow driver to signal mac80211 that they will not check the keyID in
MPDUs when aggregating them and that they expect mac80211 to stop Tx
aggregation when rekeying a connection using Extended Key ID.
Signed-off-by: NAlexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For old commands, it's fine to have .type = NLA_UNSPEC and it
behaves the same as NLA_MIN_LEN. However, for new commands with
strict validation this is no longer true, and for policy export
to userspace these are also ignored.

Fix up the remaining ones that don't have a type.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the BSS is expired during connection, the connect result will
trigger a kernel warning. Ideally cfg80211 should hold the BSS
before the connection is attempted, but as the BSSID is not known
in case of auth/assoc MLME offload (connect op) it doesn't.

For those drivers without the connect op cfg80211 holds down the
reference so it wil not be removed from list.

Fix this by removing the warning and silently adding the BSS back to
the bss list which is return by the driver (with proper BSSID set) or
in case the BSS is already added use that.

The requirements for drivers are documented in the API's.
Signed-off-by: NChaitanya Tata <chaitanya.tata@bluwireless.co.uk>
[formatting fixes, keep old timestamp]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Fix blow sparse warning introduced by a previous patch.
- restricted __le32 degrades to integer
- restricted __le16 degrades to integer

Fixes: d3982312 ("enetc: add hardware timestamping support")
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL_GIGA_MAC_VER_01 is RTL8169, the ancestor of the chip family.
It didn't have an internal PHY and I've never seen it in the wild.
What isn't there doesn't need to be maintained, so let's remove
support for it.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Certain parts of the PHY initialization are the same for sub versions
1 and 2 of RTL8168d. So let's factor this out to simplify the code.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: small improvements

Series with small improvements.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the appropriate enum type for member mac_version. And don't assign
a fixed value to RTL_GIGA_MAC_NONE, there's no benefit in it.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove not needed return statement.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtl_hw_init_8168ep() can be removed, this simplifies the code.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix sparse warning:

drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:6216:14:
 warning: symbol 't4_get_tp_e2c_map' was not declared. Should it be static?
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I was really surprised that the IPv6 mtu exception followed by redirect
test was passing as nothing about the code suggests it should. The problem
is actually with the logic in the test script.

Fix the test cases as follows:
1. add debug function to dump the initial and redirect gateway addresses
   for ipv6. This is shown only in verbose mode. It helps verify the
   output of 'route get'.

2. fix the check_exception logic for the reset case to make sure that
   for IPv4 neither mtu nor redirect appears in the 'route get' output.
   For IPv6, make sure mtu is not present and the gateway is the initial
   R1 lladdr.

3. fix the reset logic by using a function to delete the routes added by
   initial_route_*. This format works better for the nexthop version of
   the tests.

While improving the test cases, go ahead and ensure that forwarding is
disabled since IPv6 redirect requires it.

Also, runs with kernel debugging enabled sometimes show a failure with
one of the ipv4 tests, so spread the pings over longer time interval.

The end result is that 2 tests now show failures:

TEST: IPv6: mtu exception plus redirect                    [FAIL]

and the VRF version.

This is a bug in the IPv6 logic that will need to be fixed
separately. Redirect followed by MTU works because __ip6_rt_update_pmtu
hits the 'if (!rt6_cache_allowed_for_pmtu(rt6))' path and updates the
mtu on the exception rt6_info.

MTU followed by redirect does not have this logic. rt6_do_redirect
creates a new exception and then rt6_insert_exception removes the old
one which has the MTU exception.

Fixes: ec810535 ("selftests: Add redirect tests")
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pointer n is being assigned a value however this value is
never read in the code block and the end of the code block
continues to the next loop iteration. Clean up the code by
removing the redundant assignment.

Fixes: 1bff1a0c ("ipv4: Add function to send route updates")
Addresses-Coverity: ("Unused value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY drivers don't have to and shouldn't fiddle with phylib internals.
Most of the code in bcm87xx_config_init() can be removed because
phylib takes care.

In addition I replaced usage of PHY_10GBIT_FEC_FEATURES with an
implementation of the get_features callback. PHY_10GBIT_FEC_FEATURES
is used by this driver only and it's questionable whether there
will be any other PHY supporting this mode only. Having said that
in one of the next kernel versions we may decide to remove it.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
inet: frags: avoid possible races at netns dismantle

This patch series fixes a race happening on netns dismantle with
frag queues. While rhashtable_free_and_destroy() is running,
concurrent timers might run inet_frag_kill() and attempt
rhashtable_remove_fast() calls. This is not allowed by
rhashtable logic.

Since I do not want to add expensive synchronize_rcu() calls
in the netns dismantle path, I had to no longer inline
netns_frags structures, but dynamically allocate them.

The ten first patches make this preparation, so that
the last patch clearly shows the fix.

As this patch series is not exactly trivial, I chose to
target 5.3. We will backport it once soaked a bit.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

syszbot found an interesting use-after-free [1] happening
while IPv4 fragment rhashtable was destroyed at netns dismantle.

While no insertions can possibly happen at the time a dismantling
netns is destroying this rhashtable, timers can still fire and
attempt to remove elements from this rhashtable.

This is forbidden, since rhashtable_free_and_destroy() has
no synchronization against concurrent inserts and deletes.

Add a new fqdir->dead flag so that timers do not attempt
a rhashtable_remove_fast() operation.

We also have to respect an RCU grace period before starting
the rhashtable_free_and_destroy() from process context,
thus we use rcu_work infrastructure.

This is a refinement of a prior rough attempt to fix this bug :
https://marc.info/?l=linux-netdev&m=153845936820900&w=2

Since the rhashtable cleanup is now deferred to a work queue,
netns dismantles should be slightly faster.

[1]
BUG: KASAN: use-after-free in __read_once_size include/linux/compiler.h:194 [inline]
BUG: KASAN: use-after-free in rhashtable_last_table+0x162/0x180 lib/rhashtable.c:212
Read of size 8 at addr ffff8880a6497b70 by task kworker/0:0/5

CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1+ #2
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events rht_deferred_worker
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x172/0x1f0 lib/dump_stack.c:113
 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:188
 __kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
 kasan_report+0x12/0x20 mm/kasan/common.c:614
 __asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132
 __read_once_size include/linux/compiler.h:194 [inline]
 rhashtable_last_table+0x162/0x180 lib/rhashtable.c:212
 rht_deferred_worker+0x111/0x2030 lib/rhashtable.c:411
 process_one_work+0x989/0x1790 kernel/workqueue.c:2269
 worker_thread+0x98/0xe40 kernel/workqueue.c:2415
 kthread+0x354/0x420 kernel/kthread.c:255
 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352

Allocated by task 32687:
 save_stack+0x23/0x90 mm/kasan/common.c:71
 set_track mm/kasan/common.c:79 [inline]
 __kasan_kmalloc mm/kasan/common.c:489 [inline]
 __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:462
 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:503
 __do_kmalloc_node mm/slab.c:3620 [inline]
 __kmalloc_node+0x4e/0x70 mm/slab.c:3627
 kmalloc_node include/linux/slab.h:590 [inline]
 kvmalloc_node+0x68/0x100 mm/util.c:431
 kvmalloc include/linux/mm.h:637 [inline]
 kvzalloc include/linux/mm.h:645 [inline]
 bucket_table_alloc+0x90/0x480 lib/rhashtable.c:178
 rhashtable_init+0x3f4/0x7b0 lib/rhashtable.c:1057
 inet_frags_init_net include/net/inet_frag.h:109 [inline]
 ipv4_frags_init_net+0x182/0x410 net/ipv4/ip_fragment.c:683
 ops_init+0xb3/0x410 net/core/net_namespace.c:130
 setup_net+0x2d3/0x740 net/core/net_namespace.c:316
 copy_net_ns+0x1df/0x340 net/core/net_namespace.c:439
 create_new_namespaces+0x400/0x7b0 kernel/nsproxy.c:107
 unshare_nsproxy_namespaces+0xc2/0x200 kernel/nsproxy.c:206
 ksys_unshare+0x440/0x980 kernel/fork.c:2692
 __do_sys_unshare kernel/fork.c:2760 [inline]
 __se_sys_unshare kernel/fork.c:2758 [inline]
 __x64_sys_unshare+0x31/0x40 kernel/fork.c:2758
 do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 7:
 save_stack+0x23/0x90 mm/kasan/common.c:71
 set_track mm/kasan/common.c:79 [inline]
 __kasan_slab_free+0x102/0x150 mm/kasan/common.c:451
 kasan_slab_free+0xe/0x10 mm/kasan/common.c:459
 __cache_free mm/slab.c:3432 [inline]
 kfree+0xcf/0x220 mm/slab.c:3755
 kvfree+0x61/0x70 mm/util.c:460
 bucket_table_free+0x69/0x150 lib/rhashtable.c:108
 rhashtable_free_and_destroy+0x165/0x8b0 lib/rhashtable.c:1155
 inet_frags_exit_net+0x3d/0x50 net/ipv4/inet_fragment.c:152
 ipv4_frags_exit_net+0x73/0x90 net/ipv4/ip_fragment.c:695
 ops_exit_list.isra.0+0xaa/0x150 net/core/net_namespace.c:154
 cleanup_net+0x3fb/0x960 net/core/net_namespace.c:553
 process_one_work+0x989/0x1790 kernel/workqueue.c:2269
 worker_thread+0x98/0xe40 kernel/workqueue.c:2415
 kthread+0x354/0x420 kernel/kthread.c:255
 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352

The buggy address belongs to the object at ffff8880a6497b40
 which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 48 bytes inside of
 1024-byte region [ffff8880a6497b40, ffff8880a6497f40)
The buggy address belongs to the page:
page:ffffea0002992580 refcount:1 mapcount:0 mapping:ffff8880aa400ac0 index:0xffff8880a64964c0 compound_mapcount: 0
flags: 0x1fffc0000010200(slab|head)
raw: 01fffc0000010200 ffffea0002916e88 ffffea000218fe08 ffff8880aa400ac0
raw: ffff8880a64964c0 ffff8880a6496040 0000000100000005 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff8880a6497a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff8880a6497a80: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff8880a6497b00: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
                                                             ^
 ffff8880a6497b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff8880a6497c00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

Fixes: 648700f7 ("inet: frags: use rhashtables for reassembly units")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following patch will add rcu grace period before fqdir
rhashtable destruction, so we need to dynamically allocate
fqdir structures to not force expensive synchronize_rcu() calls
in netns dismantle path.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fqdir will soon be dynamically allocated.

We need to reach the struct net pointer from fqdir,
so add it, and replace the various container_of() constructs
by direct access to the new field.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And pass an extra parameter, since we will soon
dynamically allocate fqdir structures.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(struct net *)->ieee802154_lowpan.fqdir will soon be a pointer, so make
sure lowpan_frags_ns_ctl_table[] does not reference init_net.

lowpan_frags_ns_sysctl_register() can perform the needed initialization
for all netns.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(struct net *)->nf_frag.fqdir will soon be a pointer, so make
sure nf_ct_frag6_sysctl_table[] does not reference init_net.

nf_ct_frag6_sysctl_register() can perform the needed initialization
for all netns.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(struct net *)->ipv6.fqdir will soon be a pointer, so make
sure ip6_frags_ns_ctl_table[] does not reference init_net.

ip6_frags_ns_ctl_register() can perform the needed initialization
for all netns.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(struct net *)->ipv4.fqdir will soon be a pointer, so make
sure ip4_frags_ns_ctl_table[] does not reference init_net.

ip4_frags_ns_ctl_register() can perform the needed initialization
for all netns.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the @frags fields from structs netns_ipv4, netns_ipv6,
netns_nf_frag and netns_ieee802154_lowpan to @fqdir
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) struct netns_frags is renamed to struct fqdir
  This structure is really holding many frag queues in a hash table.

2) (struct inet_frag_queue)->net field is renamed to fqdir
  since net is generally associated to a 'struct net' pointer
  in networking stack.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: add aRFS feature and fix FEC bugs for HNS3 driver

This patchset adds some new features support and fixes some bugs:
[Patch 1/4 - 3/4] adds support for aRFS
[Patch 4/4] fix FEC configuration issue
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FEC capbility may be changed with port speed changes. Driver
needs to read the active FEC mode, and update FEC capability
when port speed changes.

Fixes: 7e6ec914 ("net: hns3: add support for FEC encoding control")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds aRFS support for PF. The aRFS rules are also
stored in the hardware flow director table, Use the existing
filter management functions to insert TCPv4/UDPv4/TCPv6/UDPv6
flow director filters. To avoid rule conflict, once user adds
flow director rules with ethtool, the aRFS will be disabled,
and clear exist aRFS rules. Once all user configure rules were
removed, aRFS can work again.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to be compatible with aRFS rules, this patch adds
spin_lock for flow director rule adding, deleting, querying,
and packages the rule configuration.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate CPU rmap and add entry for each irq. CPU rmap is
used in aRFS to get the queue number of the rx completion
interrupts.

In additional, remove the calling of
irq_set_affinity_notifier() in hns3_nic_init_irq(), because
we have registered notifier in irq_cpu_rmap_add() for each
vector, otherwise it may cause use-after-free issue.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Oleksij Rempel says:

====================
MIPS: ath79: add ag71xx support

2019.05.24 v6:
- ag71xx: remove double union
- ag71xx: reverse Christmas tree for all functions
- ag71xx: add Reviewed-by: Andrew Lunn <andrew@lunn.ch>

2019.05.20 v5:
- ag71xx: remove MII_CMD_WRITE, the name is confusing. It is
  actually disables MII_CMD_READ.
- ag71xx: rework ag71xx_mdio_mii_read/write
- ag71xx: set proper mask for the addr in ag71xx_mdio_mii_read/write
- Kconfig: remove MDIO_BITBANG
- ag71xx: ./scripts/checkpatch.pl it.

2019.05.19 v4:
- DT: define eth and mdio clocks
- ag71xx: remove module parameters
- ag71xx: return proper error value on mdio_read/write
- ag71xx: use proper mdio clock registration
- ag71xx: add ag71xx_dma_wait_stop() for ag71xx_dma_reset()
- ag71xx: remove ag71xx_speed_str()
- ag71xx: use phydev->link/sped/duplex instead of ag-> variants
- ag71xx: use WARN() instead of BUG()
- ag71xx: drop big part of ag71xx_phy_link_adjust()
- ag71xx: drop most of ag71xx_do_ioctl()
- ag71xx: register eth clock
- ag71xx: remove AG71XX_ETH0_NO_MDIO quirk.

2019.04.22 v3:
- ag71xx: use phy_modes() instead of ag71xx_get_phy_if_mode_name()
- ag71xx: remove .ndo_poll_controller support
- ag71xx: unregister_netdev before disconnecting phy.

2019.04.18 v2:
- ag71xx: add list of openwrt authors
- ag71xx: remove redundant PHY_POLL assignment
- ag71xx: use phy_attached_info instead of netif_info
- ag71xx: remove redundant netif_carrier_off() on .stop.
- DT: use "ethernet" instead of "eth"

This patch series provide ethernet support for many Atheros/QCA
MIPS based SoCs.

I reworked ag71xx driver which was previously maintained within OpenWRT
repository. So far, following changes was made to make upstreaming
easier:
- everything what can be some how used in user space was removed. Most
  of it was debug functionality.
- most of deficetree bindings was removed. Not every thing made sense
  and most of it is SoC specific, so it is possible to detect it by
  compatible.
- mac and mdio parts are merged in to one driver. It makes easier to
  maintaine SoC specific quirks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for Atheros/QCA AR7XXX/AR9XXX/QCA95XX built-in ethernet mac support
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethernet nodes supported by ag71xx driver.
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add binding documentation for Atheros/QCA networking IP core used
in many routers.
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michal Kalderon says:

====================
qed*: Improve performance on 100G link for offload protocols

This patch series modifies the current implementation of PF selection.
The refactoring of the llh code enables setting additional filters
(mac / protocol) per PF, and improves performance for offload protocols
(RoCE, iWARP, iSCSI, fcoe) on 100G link (was capped at 90G per single
PF).

Improved performance on 100G link is achieved by configuring engine
affinty to each PF.
The engine affinity is read from the Management FW and hw is configured accordingly.
A new hw resource called PPFID is exposed and an API is introduced to utilize
it. This additional resource enables setting the affinity of a PF and providing
more classification rules per PF.
qedr,qedi,qedf are also modified as part of the series. Without the
changes functionality is broken.

v1 --> v2
---------
- Remove iWARP module parameter. Instead use devlink param infrastructure
  for setting the iwarp_cmt mode. Additional patch added to the series for
  adding the devlink support.

- Fix kbuild test robot warning on qed_llh_filter initialization.

- Remove comments inside function calls
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>