For a000 devices the binding API needs to include relevant
lmac ID - support the new API.
The new API should be used regardless if the device had CDB or
not. If there is no actual CDB support the binding is bound
to first lmac regardless of the band.
There are some functionality changes in binding restrictions
and quota allocations that will be handled in future patches.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This fixes a long-standing bug that was introduced when this code
was introduced: cfg80211 passes a pointer, but we treat it as if
it was passing a value. The result is that we pass the pointer to
the firmware, instead of the value. It's not clear how this could
ever have worked, unless the firmware is ignoring this value.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support getting alive from two LMACs and dumping debug
data from both.
Deprecate older alive notifications no one is using.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For unified images, we shouldn't restart the HW if suspend fails.  The
only reason for restarting the HW with non-unified images is to go
back to the D0 image.

Fixes: 23ae6128 ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

With unified images, we need to make sure the net-detect scan is
stopped after resuming, since we don't restart the FW.  Also, we need
to make sure we check if there are enough scan slots available to run
it, as we do with other scans.

Fixes: commit 23ae6128 ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If the suspend flow fails, we restart the hardware to go back to
the D0 image (with non-unified images), but we don't comply with
the fw_restart module parameter.  If something goes wrong when
starting the D3 image, we may want to debug it, so we should
comply with the fw_restart flag to avoid clearing everything up
and losing the firmware state when the error occurred.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When a unified D0/D3 image is used, we don't restart the FW in the
D0->D3->D0 transitions.  Therefore, the d3_test functionality should
not call ieee8021_restart_hw() when the resuming either.

Fixes: commit 23ae6128 ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Getting the mvm station out of station id requires dereferencing
the station id to get ieee80211_sta, then checking for pointer
validity and only then extract mvm station out.
Given that there are helpers to do it - use them instead of
duplicating the code whenever we need only mvm station.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

"DQA" is shorthand for "dynamic queue allocation". This
enables on-demand allocation of queues per RA/TID rather than
statically allocating per vif, thus allowing a potential
benefit of various factors.

Please refer to the DOC section this patch adds to sta.h to
see a more in-depth explanation of this feature.

There are many things to take into consideration when working
in DQA mode, and this patch is only one in a series. Note that
default operation mode is non-DQA mode, unless the FW
indicates that it supports DQA mode.

This patch enables support of DQA for a station connected to
an AP, and works in a non-aggregated mode.

When a frame for an unused RA/TID arrives at the driver, it
isn't TXed immediately, but deferred first until a suitable
queue is first allocated for it, and then TXed by a worker
that both allocates the queues and TXes deferred traffic.

When a STA is removed, its queues goes back into the queue
pools for reuse as needed.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Leaving ucode_loaded to true after stop_device() has been called
is a recipe for problems. Flows that are not sync'ed with the
driver life cycle (like debugfs hooks and thermal hooks) must
check that the firmware is loaded before they interact with it.
Therefore we need to keep this variable updated with the real
status of the firmware.
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently when entering D3 with WOWLAN configured, we enable in the
configuration flags beacon storing, and do not disable beacon
filtering, and do not wake up from a magic packet.

Having both enabled is wrong (should not have both enabled),
and causes problems in the RX queues in the FW, causing
the FW not to recognize the magic packet when it comes.

Disable beacon storing in wowlan configuration.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If protocol offloading is configured, the fw might generate some
frames (e.g. arp response) on its own during d3/d0i3.

On d3/d0i3 exit the driver queries the updated PN (if relevant),
and updates its keys (for the d0i3 case, this is done by
iwl_mvm_d0i3_exit_work(), which is scheduled on d0i3 exit)

While in d0i3, iwlmvm defers tx frames until d0i3 exit, and
then continues their processing.

This is problematic with TKIP, since the frame's PN has already
been set at this stage (in contrast to CCMP, where the PN is
being set only later on), so both the frame's PN and the upcoming
PN update (from d0i3 exit work) might be wrong.

Fix it by moving the TX PN assignment (for TKIP) to the driver,
similarly to CCMP.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently firmware is configured to filter out beacons. In case
a beacon was changed - it is waking the host.
However, some vendors change their IEs frequently without any
significant change, and redundant wakeups are triggered as a
result.
As a solution disable beacon filtering when entering d0i3.
Instead, firmware will store the latest beacon and upon exiting
d0i3 it will send it up to the host, so the host can act upon
changes (if there were any).
This beacon will arrive as a dedicated notification - support it
as well.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently when the driver is configured with wowlan parameters, and enters
D3 mode, the driver switches the FW image to D3, and when it exists
suspend, it reloads the D0 image.

If the firmware supports the consolidation of the D0 & D3 images there is
no need to load the D3 image on suspend, and no need to reload the D0
image on resume.

Do not switch images on suspend / resume, for firmwares that support
consolidated images.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

gtkdata->mvm wasn't set in iwl_mvm_d0i3_update_keys,
resulting in kernel panic in some flows (when mvm
is actually used...)

Fixes: a3f7ba5c ("iwlwifi: update key params on d0i3 entrance/exit")
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As we're working on multi-queue RX, we want to parallelise checking
the PN in order to avoid having to serialise the RX processing.

It may seem that doing parallel PN checking is insecure, but it turns
out to be OK because queue assignment is done based on the data in the
frame (IP/TCP) and thus cannot be manipulated by an attacker, since
the data is encrypted and must first have been decrypted successfully.

There are some corner cases, in particular when the peer starts using
fragmentation which redirects the packet to the default queue. However
this redirection is remembered (for the STA, per TID) and thus cannot
be exploited by an attacker either.

Leave checking on the default queue (queue 0) to mac80211, since we
get fragmented packets there and those are subject to stricter checks
during reassembly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to let the fw do offloading properly, we need
to provide various key data (e.g. PN).

Configure the params on d0i3 entrance, and update them
back on d0i3 exit.

Since d3 code is now called in d0i3 which requires runtime
pm only, make d3.0 depend on CONFIG_PM (rather than
CONFIG_PM_SLEEP), and add required #ifdefs and wrappers
where needed, so both CONFIG_PM=n and CONFIG_PM_RUNTIME=n
configurations will build correctly.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Firmware will support filtering multicast L3 packets.
The L3 filtering is configured by the WOWLAN_CONFIG command.
All flags should be enabled by default.
Older firmware is not affected as it does not look into
this field.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of keeping the fw_key_table bits set when the keys are removed
(i.e. in D3 entry or HW_RESTART flows), clear them and set them again
only when the keys have been successfully re-added.  This makes the
bitmask more closely tied to the actual firmware programming.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

RFC4862 states that "In all cases, a node MUST NOT respond to
a Neighbor Solicitation for a tentative address".
Currently the driver configures the NS offload and does not wait
for address to become permanent, thus violating the RFC.
Just removing the address from the address list is not good enough
for all cases, since the NS messages are needed for the duplicate
address detection and should not be discarded.

For d0i3 disable NS offload. Put tentative address in the address
list so the NS packet will not be filtered out by ucode.
For D3 the platform will not wake from NS packets - so enable
NS offload while removing the tentative address from the list.

Given that now NS offload might be disabled, and that the ucode
uses the IP data for other puroposes (L3 filtering) add two
independent flags indicating if IPv4\IPv6 data is valid.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The d0i3_mode variable is used to distinguish between transports that
handle d0i3 entry during suspend by themselves (i.e. the slave
transports) and those which rely on the op_mode layer to do it.  The
reason why the former do it by themselves is that they need to
transition from d0i3 in runtime_suspend into d0i3 in system-wide
suspend and this transition needs to happen before the op_mode's
suspend flow is called.

The wowlan_d0i3 element is also a bit confusing, because it just
reflects the wowlan->any value for the trans to understand.  This is a
bit unclear in the code and not generic enough for future use.

To make it clearer and to generalize the platform power mode settings,
introduce two variables to indicate the platform power management
modes used by the transport.

Additionally, in order not to take too big a step in one patch, treat
this new variables semantically in the same way as the old d0i3_mode
element, introducing a iwl_mvm_enter_d0i3_on_suspend() function to
help with that.

This commit also adds the foundation for a new concept where the
firmware configuration state (i.e. D0, D3 or D0i3) is abstracted from
the platform PM mode we are in (i.e. runtime suspend or system-wide
suspend).
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

commit 9a4c830007817e ("iwlwifi: mvm: refactor d3 key
update functions") refactored some code into
iwl_mvm_wowlan_config_key_params() function, but the
return value was never checked, and not all the function
flows returned valid values. fix it.

Fixes: ac8ef0ce ("iwlwifi: mvm: refactor d3 key update functions")
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the wifi wakes up the system, we need to report it via calling
pm_wakeup_event for lucid sleep. This is so userspace knowns that the
wifi woke up the system via the /sys/power/wakeup_type sysfs interface.
Signed-off-by: NDerek Basehore <dbasehore@chromium.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We need to reuse the key update logic for d0i3
as well.

Add some parameters to deal with the constraints
implied by the d0i3 flow (specifically, support
non-SYNC commands, and don't take mutexes that
might deadlock).

Change some commands to be ASYNC, in order
to simplify locking a bit.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the netdetect debugfs entry was removed, the nd_config element
was accidentally left in the iwl_mvm structure.  Remove it.

Fixes: dbb04b0d ("iwlwifi: mvm: remove netdetect debugfs entry")
Reported-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This function updates the pairwise keys as well.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When entering D3, we need to use hardcoded key indices because the
firmware requires that.  To do so, we are overwriting the HW key index
in the keyconf structure, which makes it impossible to reuse the
indices that were used before entering D3.  Additionally, we overwrite
all the non-PTK keys with index 1, because the firmware only allows
one non-PTK key to be set.  This is bad, because when we resume, we
may try to set more than one key with index 1, which will obviously
fail.

To fix this, allow the callers to set a pre-defined index to use in
iwl_mvm_set_sta_key() instead of relying on the hw_key_idx value from
the keyconf struct (which requires overwriting it).  In normal cases,
the caller can pass STA_KEY_IDX_INVALID, which will cause a new key
offset to be chosen.  During HW_RESTART, we pass the offset that is in
use.  And during D3 entry, we pass the hardcoded indices we need to
use.

Additionally, don't clear the fw_key_table in D3 entry, so that the
flags are still set with the pre-D3 values when exiting D3.

fixes=I3165c22362483f0152d9ec1d2a987fb5529727c1

Fixes: b546dcd6 ("iwlwifi: mvm: don't reset key index on HW restart")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.

Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When going into/coming out of D3, the TX PN must be programmed into
and restored from the firmware respectively. The restore was broken
due to my previous commit to move PN assignment into the driver.
Sending the PN to the firmware still worked since we now use the
counter that's shared with mac80211, but accessing it through the
mac80211 API makes no sense now.

Fix this by reading/writing the counter directly. This actually
simplifies the code since we don't need to round-trip through the
key_seq structure.

Fixes: ca8c0f4b ("iwlwifi: mvm: move TX PN assignment for CCMP to the driver")
Cc: <stable@vger.kernel.org> [4.1+]
Reported-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If we are in d0i3 when entering suspend, we leave d0i3 so that
mac80211 can call us to remove connections or whatever before going to
suspend.  We do this by calling pm_runtime_resume() early in the slave
transport flow and reactivating it later, when the wiphy suspend flow
runs.

The problem is that we queue a work in order to leave d0i3.  If this
work hasn't run yet when the wiphy suspend flow is called, we have a
race and entering d0i3 fails (because we're still holding the
IWL_MVM_REF_EXIT_WORK reference).

To solve this, simply flush the d0i3_exit_work at the beginning of the
iwl_mvm_suspend() function.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Add support for extended command id in notification system.
Extended command id header contains group id in addition to command id.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some CSR registers have to be configured also
in case of suspend/resume with unified image
(which doesn't includes reconfiguration flow).

Reuse the existing d3_suspend/d3_resume trans ops,
while making sure some configurations are a bit
different, according to the wowlan type.

After this change, we no longer need the special
wowlan_d0i3 configurations done in iwl_pci_resume,
as they are already being done in the d3_resume op.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow the transport layer to return an error upon suspend.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This reverts commit 088070a2.

When working in d0i3_on_idle mode, we explicitly go out
of d0i3 on resume (so other potential commands could
be sent).

However, D0I3_DEFER_WAKEUP is currently cleared on
resume complete (which happens only later on), causing
d0i3 exit to timeout.

Since mac80211 was modified to accept incoming frames
once drv_resume was called, we can safely revert this
patch, and handle the pending work on iwl_mvm_resume().
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

On resume, all the interrupts are masked (CSR_INT_MASK is 0),
and ict is disabled.

Re-configure them both.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The regular and scheduled scan functions are very similar, so they can
be combined into one.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The iwl_mvm_scan_offload_stop() function is used to stop LMAC regular
scan, stop LMAC scheduled scan and stop UMAC scheduled scans (but not
UMAC regular scans), making it very difficult to read.

Reorganize the scan stopping functions by creating separate functions
to stop regular and scheduled scans, separating the LMAC stopping part
of the code from the rest and renaming the offload_stop function to
iwl_mvm_lmac_scan_stop().
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

After the scan refactor, the order of the SSIDs passed to the firmware
in all scans (including net-detect) are inverted.  This was causing
the reporting code to use the wrong SSIDs.  To fix this, invert the
array index when accessing the saved match SSIDs to report the
wake-up.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>