Signed-off-by: NGyungoh Yoo <jack.yoo@skyworksinc.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add a DT binding that lets the DMIC reference voltage source be
specified for each input.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Change flash cell identifiers from max77693-flash to max77693-led
to avoid confusion with NOR/NAND Flash.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

In Quark X1000, there's a single PCI device that provides both
an I2C controller and a GPIO controller. This MFD driver will
split the 2 devices for their respective drivers.

This patch is based on Josef Ahmad's initial work for Quark enabling.
Acked-by: NMichael Turquette <mturquette@linaro.org>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWeike Chen <alvin.chen@intel.com>
Signed-off-by: NRaymond Tan <raymond.tan@intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Rk808 has a under voltage detect function, when the voltage of buck is
under 85% the target voltage, the buck output will reset. But if the
power load is too heavy, this function maybe err, when current over
4.2A, although the voltage is normal, but RK808 mistakenly think it is
under 85%, and reset the buck. So let's disable this function.
Signed-off-by: NChris Zhong <zyw@rock-chips.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The seq_printf return value, because it's frequently misused,
will eventually be converted to void.

See: commit 1f33c41c ("seq_file: Rename seq_overflow() to
     seq_has_overflowed() and make public")
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Since commit 0b271258(linux-next.git) this driver uses regmap_irq and so needs
to select REGMAP_IRQ.

This fixes the following compilation errors:
ERROR: "regmap_irq_get_domain" [drivers/mfd/rt5033.ko] undefined!
ERROR: "regmap_add_irq_chip" [drivers/mfd/rt5033.ko] undefined!
Signed-off-by: NArtem Savkov <asavkov@redhat.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NAdam Ward <adam.ward.opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The range of registers used by this driver exceeds that available
via SPI with no paging (127), so we have to override the values
from the default config which is set-up for I2C access.
Also change SPI settings to match device's recommended OTP values.
Signed-off-by: NAdam Ward <adam.ward.opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds MAX77843 core/irq driver to support PMIC,
MUIC(Micro USB Interface Controller), Charger, Fuel Gauge,
LED and Haptic device.
Signed-off-by: NJaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This adds support for the MediaTek MT6397 PMIC. This is a
multifunction device with the following sub modules:

- Regulator
- RTC
- Audio codec
- GPIO
- Clock

It is interfaced to the host controller using SPI interface by a proprietary
hardware called PMIC wrapper or pwrap. MT6397 MFD is a child device of the
pwrap.

Signed-off-by: Flora Fu, MediaTek
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

There is no need to print additional ENOMEM message for
sec_platform_data allocation failure.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The WTSR (Watchdog Timer Software Reset) and SMPL (Sudden Momentary
Power Loss) were removed from rtc-s5m driver because they were not used.
Remove them (and on/off interrupt) from main MFD driver and header.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The WTSR (Watchdog Timer Software Reset) and SMPL (Sudden Momentary
Power Loss) are never enabled. These are left-overs from board files.
After removing them the driver's shutdown callback is empty so get rid
of it as well.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

pcr_dbg is a wrapper of dev_dbg, which can save some code,
and help to enable/disable debug message static.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add support for new chip rts525A.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

add support for new chip rts524A.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

To enable/disable ASPM we should find LINK CONTROL register
in PCI config space. All old chip use 0x80 address, but new
chip may use another address, so we using pci_find_capability()
to get LINK CONTROL address.

rtsx_gops.c was removed, we consider to put some common operations
to this file, but the actual thing is, only a group of chips
are in common ops1, and another group of chips in common ops2,
it is hard to decide put which ops into generic ops file.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Update some phy register name and value for rts5249,
the updated value makes chip more stable on some platform.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

update card drive settings, This setting can be used for rts5249
rts524A and rts525A.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

PETXCFG is defined at 0xFF03, the old 0xFE49 not used any more.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

In one shot mode, sequencer automatically disables all enabled steps at
the end of each cycle. (both ADC steps and TSC steps) Hence these steps
need not be saved in reg_se_cache for clearing these steps at a later
stage.
Also, when ADC wakes up Sequencer should not be busy executing any of the
config steps except for the charge step. Previously charge step was 1 ADC
clock cycle and hence it was ignored.
TSC steps are always disabled at the end of each conversion cycle, hence
there is no need to explicitly disable TSC steps by writing 0 to REG_SE.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Now, as all VE platforms have to be booted with DT,
the code handling non-DT case can be removed.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds the DMI system ID of the Kontron COMe-cBL6 board to
the Kontron PLD driver. The list of supported products in the module
description is also updated.
Signed-off-by: NMichael Brunner <michael.brunner@kontron.com>
Acked-by: NChristian Rauch <christian.rauch@kontron.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Name changes to the battery cell structure to a
more generic cell type: fuel gauge.
Signed-off-by: NTodd Brandt <todd.e.brandt@linux.intel.com>
Acked-By: NSebastian Reichel <sre@kernel.org>
Acked-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Surely GPIO irq will be used as an input pin so make sure its direction is
set after requesting.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

It is usually better to pass actual error code from a function call than
mangling it to another.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

intel_soc_pmic_find_gpio_irq() tries to find a GPIO interrupt but doesn't
select between it or I2C interrupt so it makes more sense to move this
comment to intel_soc_pmic_i2c_probe() with minor edits.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This adds support for the Wolfson Microelectronics WM8280 and WM8281
codecs.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
[Lee: Minor fixup to remove potentially uninitialised variable. ]
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Upstream checkpatch now requires this.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

For, !HAVE_CLK the clk API returns a NULL cookie. Rework the
initialization code to handle that. If clk_get_rate() delivers 0, we use
the fallback mechanisms. The patch is pretty easy when ignoring white
space issues (git diff -b).
Suggested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Tested-by: NMax Filippov <jcmvbkbc@gmail.com>

The exynos_tmu_data() function should on entrance test not only for valid
data pointer, but also for data->tmu_read one.
It is important, since afterwards it is dereferenced to get temperature code.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Tested-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>

Code that does this:

	if (!(d_unhashed(tmp) && tmp->d_inode)) {
		...
		simple_unlink(parent->d_inode, tmp);
	}

is broken because:

	!(d_unhashed(tmp) && tmp->d_inode)

is equivalent to:

	!d_unhashed(tmp) || !tmp->d_inode

so it is possible to get into simple_unlink() with tmp->d_inode == NULL.

simple_unlink(), however, assumes tmp->d_inode cannot be NULL.

I think that what was meant is this:

	!d_unhashed(tmp) && tmp->d_inode

and that the logical-not operator or the final close-bracket was misplaced.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
cc: Bryan O'Sullivan <bos@pathscale.com>
cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

We don't really need to recalculate the effective rate of a clock when a
per-user clock is removed, if the constraints of the later aren't
limiting the requested rate.

This was causing problems with clocks that never had a rate set before,
as rate_req would be zero. Though this could be considered a bug in the
implementation of those clocks, this should be checked somewhere else.

Fixes: 1c8e6004 ("clk: Add rate constraints to clocks")
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

From a locking point of view it is safe to check waiting_msg without
a lock, but there is a memory ordering issue that causes it to
possibly not be set right when viewed from another processor.  We are
already claiming a lock right after that, move the check to inside
the lock to enforce the memory ordering.
Signed-off-by: NCorey Minyard <cminyard@mvista.com>