Check the BNXT_STATE_OPEN flag instead of netif_running() in
bnxt_set_rx_mode().  If the driver is going through any reset, such
as firmware reset or even TX timeout, it may not be ready to set the RX
mode and may crash.  The new rx mode settings will be picked up when
the device is opened again later.

Fixes: 230d1f0d ("bnxt_en: Handle firmware reset.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new function bnxt_get_registered_vfs() to handle the work
of getting the number of registered VFs under #ifdef CONFIG_BNXT_SRIOV.
The main code will call this function and will always work correctly
whether CONFIG_BNXT_SRIOV is set or not.

Fixes: 230d1f0d ("bnxt_en: Handle firmware reset.")
Reported-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Health show command example and output:

$ devlink health show pci/0000:af:00.0 reporter fw_fatal

pci/0000:af:00.0:
  name fw_fatal
    state healthy error 1 recover 1 grace_period 0 auto_recover true

Fatal events from firmware or missing periodic heartbeats will
be reported and recovery will be handled.

We also turn on the support flags when we register with the firmware to
enable this health and recovery feature in the firmware.

Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This call will handle fatal firmware errors by forcing a reset on the
firmware.  The master function driver will carry out the forced reset.
The sequence will go through the same bnxt_fw_reset_task() workqueue.
This fatal reset differs from the non-fatal reset at the beginning
stages.  From the BNXT_FW_RESET_STATE_ENABLE_DEV state onwards where
the firmware is coming out of reset, it is practically identical to the
non-fatal reset.

The next patch will add the periodic heartbeat check and the devlink
reporter to report the fatal event and to initiate the bnxt_fw_exception()
call.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This state handles driver initiated chip reset during error recovery.
Only the master function will perform this step during error recovery.
The next patch will add code to initiate this reset from the master
function.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a flag to mark that the firmware has encountered fatal condition.
The driver will not send any more firmware messages and will return
error to the caller.  Fix up some clean up functions to continue
and not abort when the firmware message function returns error.

This is preparation work to fully handle firmware error recovery
under fatal conditions.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Retain the VF MAC address, default VLAN, TX rate control, trust settings
of VFs after firmware reset.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add devlink health reporter for the firmware reset event.  Once we get
the notification from firmware about the impending reset, the driver
will report this to devlink and the call to bnxt_fw_reset() will be
initiated to complete the reset sequence.

Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the bnxt_fw_reset() main function to handle firmware reset.  This
is triggered by firmware to initiate an orderly reset, for example
when a non-fatal exception condition has been detected.  bnxt_fw_reset()
will first wait for all VFs to shutdown and then start the
bnxt_fw_reset_task() work queue to go through the sequence of reset,
re-probe, and re-initialization.

The next patch will add the devlink reporter to start the sequence and
call bnxt_fw_reset().
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This event from firmware signals a coordinated reset initiated by the
firmware.  It may be triggered by some error conditions encountered
in the firmware or other orderly reset conditions.

We store the parameters from this event.  Subsequent patches will
add logic to handle reset itself using devlink reporters.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new flag will be set in subsequent patches when firmware is
going through reset.  If bnxt_close() is called while the new flag
is set, the FW reset sequence will have to be aborted because the
NIC is prematurely closed before FW reset has completed.  We also
reject SRIOV configurations while FW reset is in progress.

v2: No longer drop rtnl_lock() in close and wait for FW reset to complete.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle the async event from the firmware that enables firmware health
monitoring.  Store initial health metrics.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pre-map the GRC registers for periodic firmware health monitoring.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call the new firmware API HWRM_ERROR_RECOVERY_QCFG if it is supported
to discover the firmware health and recovery capabilities and settings.
This feature allows the driver to reset the chip if firmware crashes and
becomes unresponsive.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During IF_UP, newer firmware has a new status flag that indicates that
firmware has reset.  Add new function bnxt_fw_init_one() to re-probe the
firmware and re-setup VF resources on the PF if necessary.  If the
re-probe fails, set a flag to prevent bnxt_open() from proceeding again.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for the new firmware reset feature, some of the logic
in bnxt_init_one() and related functions will be called again after
firmware has reset.  Reset some of the flags and capabilities so that
everything that can change can be re-initialized.  Refactor some
functions to probe firmware versions and capabilities.  Check some
buffers before allocating as they may have been allocated previously.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the silent parameter is set, suppress all messages when there is
no response from firmware.  When polling for firmware to come out of
reset, no response may be normal and we want to suppress the error
messages.  Also, don't poll for the firmware DMA response if Bus Master
is disabled.  This is in preparation for error recovery when firmware
may be in error or reset state or Bus Master is disabled.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The main firmware messaging function returns the firmware defined error
code and many callers have to convert to standard error code for proper
propagation to userspace.  Convert bnxt_hwrm_do_send_msg() to return
standard error code so we can do away with all the special error code
handling by the many callers.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the non-standard -1 code with -EBUSY when there is no firmware
response after waiting for the maximum timeout.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent commit added logic to determine the appropriate statistics block
size to allocate and the size is stored in bp->hw_ring_stats_size.  But
if the firmware spec is older than 1.6.0, it is 0 and not initialized.
This causes the allocation to fail with size 0 and bnxt_open() to
abort.  Fix it by always initializing bp->hw_ring_stats_size to the
legacy default size value.

Fixes: 4e748506 ("bnxt_en: Allocate the larger per-ring statistics block for 57500 chips.")
Reported-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Tested-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When both RX buffers and RX aggregation buffers have to be
replenished at the end of NAPI, post the RX aggregation buffers first
before RX buffers.  Otherwise, we may run into a situation where
there are only RX buffers without RX aggregation buffers for a split
second.  This will cause the hardware to abort the RX packet and
report buffer errors, which will cause unnecessary cleanup by the
driver.

Ringing the Aggregation ring doorbell first before the RX ring doorbell
will prevent some of these buffer errors.  Use the same sequence during
ring initialization as well.

Fixes: 697197e5 ("bnxt_en: Re-structure doorbells.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During device shutdown, the VNIC clearing sequence needs to be modified
to free the VNIC first before freeing the RSS contexts.  The current
code is doing the reverse and we can get mis-directed RX completions
to CP ring ID 0 when the RSS contexts are freed and zeroed.  The clearing
of RSS contexts is not required with the new sequence.

Refactor the VNIC clearing logic into a new function bnxt_clear_vnic()
and do the chip specific VNIC clearing sequence.

Fixes: 7b3af4f7 ("bnxt_en: Add RSS support for 57500 chips.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the new TPA feature in the 57500 chips, we need to discover the
feature first before setting up the netdev features.  Refactor the
the firmware probe and init logic more cleanly into 2 functions and
and make these calls before setting up the netdev features.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new TPA implemantation has additional TPA counters that extend the
per-ring statistics block.  Allocate the proper size accordingly.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a more optimized hardware GRO function to setup the SKB on 57500
chips.  Some workaround code is no longer needed on 57500 chips and
the pseudo checksum is also calculated in hardware, so no need to
do the software pseudo checksum in the driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new TPA feature on 57500 supports a larger number of concurrent TPAs
(up to 1024) divided among the functions.  We need to add some logic to
map the hardware TPA ID to a software index that keeps track of each TPA
in progress.  A 1:1 direct mapping without translation would be too
wasteful as we would have to allocate 1024 TPA structures for each RX
ring on each PCI function.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With all the previous refactoring, the TPA fast path can now be
modified slightly to support TPA on the new chips.  The main
difference is that the agg completions are retrieved differently using
the bnxt_get_tpa_agg_p5() function on the new chips.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 57500 chips, hardware GRO mode cannot be determined from the TPA
end, so we need to check bp->flags to determine if we are in hardware
GRO mode or not.  Modify bnxt_set_features so that the TPA flags
in bp->flags don't change until the device is closed.  This will ensure
that the fast path can safely rely on bp->flags to determine the
TPA mode.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 2 GRO functions to set up the hardware GRO SKB fields for 2
different hardware chips have practically identical logic for
tunneled packets.  Refactor the logic into a separate bnxt_gro_tunnel()
function that can be used by both functions.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the new 57500 chips, these new RX_AGG completions are not coalesced
at the TPA_END completion.  Handle these by storing them in the
array in the bnxt_tpa_info struct, as they are seen when processing
the CMPL ring.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an aggregation array to bnxt_tpa_info struct to keep track of the
aggregation completions.  The aggregation completions are not
completed at the TPA_END completion on 57500 chips so we need to
keep track of them.  The array is only allocated on the new chips
when required.  An agg_count field is also added to keep track of the
number of these completions.

The maximum concurrent TPA is now discovered from firmware instead of
the hardcoded 64.  Add a new bp->max_tpa to keep track of maximum
configured TPA.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor the TPA logic slightly, so that the code can be more easily
extended to support TPA on the new 57500 chips.  In particular, the
logic to get the next aggregation completion is refactored into a
new function bnxt_get_agg() so that this operation is made more
generalized.  This operation will be different on the new chip in TPA
mode.  The logic to recycle the aggregation buffers has a new start
index parameter added for the same purpose.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While using net_dim, a dim_sample was used without ever initializing the
comps value. Added use of DIV_ROUND_DOWN_ULL() to prevent potential
overflow, it should not be a problem to save the final result in an int
because after the division by epms the value should not be larger than a
few thousand.

[ 1040.127124] UBSAN: Undefined behaviour in lib/dim/dim.c:78:23
[ 1040.130118] signed integer overflow:
[ 1040.131643] 134718714 * 100 cannot be represented in type 'int'

Fixes: 398c2b05 ("linux/dim: Add completions count to dim_sample")
Signed-off-by: NYamin Friedman <yaminf@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: NChuhong Yuan <hslester96@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike legacy chips, 57500 chips don't need additional VNIC resources
for aRFS/ntuple.  Fix the code accordingly so that we don't reserve
and allocate additional VNICs on 57500 chips.  Without this patch,
the driver is failing to initialize when it tries to allocate extra
VNICs.

Fixes: ac33906c ("bnxt_en: Add support for aRFS on 57500 chips.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kvzalloc already zeroes the memory during the allocation.
pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f19
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So the memset after these function is not needed.
Signed-off-by: NFuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.

This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.

Remove tc_block_offload alias.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>