To make things a bit more manageable extract a new function for
reading out common ddi port state. This means a bit of duplication
between encoders and the core since both look at the same registers,
but doesn't seem worth to make a fuzz about.

We can also remove the state readout code in intel_ddi_setup_hw_pll_state.
That code is only called from the hardware take over and not the cross
check code, and only after the crtc state is reconstructed. So we can
rely on an accurate value of crtc->config.ddi_pll_sel already.

Compared to the old code also trust the hw state more and don't
special-case port A - we want to cross-check the actual-state, not
bake in our own assumptions about how this is supposed to all be
linked up.

v2: Make use of the read-out ddi_pll_sel in intel_ddi_clock_get.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is needed by an upcoming patch that moves the PCH/CRT PLL disabling
into the post_disable hook, after which we want to keep the modeset
sequence at its current state. At this point this won't have an effect
since the PCH/CRT post_disable hook is atm a NOP.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is needed by an upcoming patch that moves the PCH/CRT PLL enabling
into the pre_enable hook, after which we want to keep the modeset
sequence at its current state. At this point this won't have an effect
since the PCH/CRT pre_enable hook is atm a NOP.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

All the other checks also check hw state, so checking our software
refcounts for the plls looks a bit odd. Also this will simplify the
conversion over to the shared dpll framework, which itself has massive
amounts of checks to make sure that we never leave a display pll
enabled when we shouldn't.

So after that conversion we should stil have a good enough coverage of
asserts for entering pc8/runtime pm on hsw/bdw.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add !mutex_is_locked() checks to intel_pin_and_fence_fb_obj() and
intel_unpin_fb_obj() to help catch failures to grab struct_mutex when
operating on fb objects.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_primary_plane_{setplane,disable} were lacking struct_mutex locking
around their GEM operations.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reported-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On HSW, the D_COMP register can be accessed through the mailbox (read
and write) or through MMIO on a MCHBAR offset (read only). On BDW, the
access should be done through MMIO on another address. So to account
for all these cases, create hsw_read_dcomp() with the correct
implementation for reading, and also fix hsw_write_dcomp() to do the
correct thing on BDW.

With this patch, we can now get back from the PC8+ state on BDW. We
were previously getting a black screen and lots of dmesg errors.
Please notice that the bug only happens when you actually reach the
PC8+ states, not when you only allow it.

Testcase: igt/pm_rpm/rte
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

That function can be used to write anything on D_COMP, not just
disable it, so print a more appropriate message.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This should hopefully simplify the display code slightly and also
solves at least one mistake in intel_pipe_set_base() where
to_intel_framebuffer(fb)->obj is referenced during local variable
initialization, before 'if (!fb)' gets checked.

Potential uses of this macro were identified via the following
Coccinelle patch:

        @@
        expression E;
        @@
        * to_intel_framebuffer(E)->obj

        @@
        expression E;
        identifier I;
        @@
          I = to_intel_framebuffer(E);
          ...
        * I->obj

v2: Rewrite some NULL tests in terms of the obj rather than the fb.
    Also add a WARN() if trying to pageflip with a disabled primary
    plane.  [Suggested by Chris Wilson]
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For whatever reason, MI_DISPLAY_FLIP fails to change tiling mode on
Baytrail, so just use CPU driven mmio flips instead.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76176Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We currently see random GPU hangs when using RCS flips with multiple
pipes on Ivybridge. Now that we have mmio flips, we can fairly cheaply
fallback to using CPU driven flips instead.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77104Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The always-on power well pixel path on haswell is routed such that it
bypasses the panel fitter when we use is. Which means the pfit CRC
source won't work in that configuration.

Add a new disallow-bypass flags to the pfit pipe config state and set
it when we want to use the pf CRC. Results in a bit of flicker, but
should get the job done. We'll also undo do it afterwards to make sure
other tests arent' negatively affected.

Totally untested due to lack of hsw laptops around here.

v2: s/disallow_bypass/force_power_well_on/ to avoid a double negative
(Damien).

v3: force_thru because roadsigns.

v4: Don't forget the power wells! Also note that until the runtime pm
for DPMS series is fully merged the simple disable/enable trick won't
work since the ->crtc_mode_set callback is still required to do nasty
things. This stuff is tricky, but I think by both fixing up
get_crtc_power_domains and the debugfs wa code we should always
grab/drop the additional power well correctly.

v5: Wrap in () as suggested by Damien to avoid setting reserved values
for the edp transcoder path on bdw+

References: https://bugs.freedesktop.org/show_bug.cgi?id=72864
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Tested-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since the root cause is understood now and with the fix

   commit 564ed191
   Author: Imre Deak <imre.deak@intel.com>
   Date:   Fri Jun 13 14:54:21 2014 +0300

       drm/i915: gmch: fix stuck primary plane due to memory self-refresh mode

in place the magic for G4x chipsets introduced with commit

   commit 61bc95c1
   Author: Egbert Eich <eich@suse.com>
   Date:   Mon Mar 4 09:24:38 2013 -0500

       DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.

to avoided occasional screen blanking on mode changes can finally
be removed.
It's been verified that Imre's fix also resolves the said issue.
Signed-off-by: NEgbert Eich <eich@suse.de>
Tested-by: NStefan Dirsch <sndirsch@suse.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Blanking/unblanking the console in a loop on an Asus T100 sometimes
leaves the console blank. After some digging I found that applying

commit 61bc95c1
Author: Egbert Eich <eich@suse.com>
Date:   Mon Mar 4 09:24:38 2013 -0500

    DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.

fixed VLV too.

In my case the problem seemed to happen already during the previous crtc
disabling and went away if I disabled self-refresh mode before disabling
the primary plane.

The root cause for this is that updates from the shadow to live plane
control register are blocked at vblank time if the memory self-refresh
mode (aka max-fifo mode on VLV) is active at that moment. The controller
checks at frame start time if the CPU is in C0 and the self-refresh mode
enable bit is set and if so activates self-reresh mode, otherwise
deactivates it. So to make sure that the plane truly gets disabled before
pipe-off we have to:

1. disable memory self-refresh mode
2. disable plane
3. wait for vblank
4. disable pipe
5. wait for pipe-off

v2:
- add explanation for the root cause from HW team (Cesar Mancini et al)
- remove note about the CPU C7S state, in my latest tests disabling it
  alone didn't make a difference
- add vblank between disabling plane and pipe (Ville)
- apply the same workaround for all gmch platforms (Ville)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that the CMNRESET deassert is part of the cmnlane power well,
intel_reset_dpio() is called too late to make any difference. We've
deasserted CMNRESET by that time, and so the off+on toggle w/a will
never kick in.

Move the workaround to intel_power_domains_init_hw() where it gets
called before we enable the init power domain.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have a slightly different way of readoing out the cdclk in
gmbus_set_freq(). Kill that and just call .get_display_clock_speed().

Also need to remove the GMBUSFREQ update from intel_i2c_reset() since
that gets called way too early. Let's do it in intel_modeset_init_hw()
instead, and also pull the initial vlv_cdclk_freq update there from
init_clock gating.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If someone is interested in the current cdclk frquency it should
be stable and not in process of changing frquency. Warn if the current
and requested cdclk don't match in .get_display_clock_spee() on vlv.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

VLV Punit doesn't support the 400MHz cdclk option, so we bypass the
Punit and poke at CCK directly. However we forgot to wait for the
frequeency change to complete. Poll the CCK clock status to make sure
the clock has changed before we fire up any pipes.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Drop the cdclk frequency to 200MHz on vlv when all pipes are off. In
theory we should be able to use 200MHz also when the pixel clock is at
most 90% of 200MHz. However in practice all we seem to get is a solid
color picture or an otherwise corrupted display.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Depending on the HPLL frequency one of the supported cdclk frquencies is
either 320MHz or 333MHz. Figure out which one it is to accurately pick
the minimal required cdclk. This would also avoid a warning from the
cdclk code where it compares the actual cdclk read out from the hardware
with a value that was calculated using valleyview_calc_cdclk().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have a standard hook for reading out the current cdclk. Move the VLV
code from valleyview_cur_cdclk() to .get_display_clock_speed().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Avoid using magic values for CCK frequency bits. Also the mask we were
using for the requested frequency was one bit too short. Fix it up.

Note: This also fixes the #define for a mask (spotted by Jesse in his
review).
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add note about mask change.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use kHz units in vlv cdclk code since that's more customary.

Also replace the precomputed 90% values with *9/10 computation
for extra clarity.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

use mm.h definition

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Apparently we can't trust this field on other platforms and need to find
some other way.

This fixes a regression introduced in
commit 27da3bdf
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Fri Apr 4 16:12:07 2014 -0700

    drm/i915: use VBT to determine whether to enumerate the VGA port
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

BDW signals the flip done interrupt immediately after the DSPSURF write
when the plane is disabled. This is true even if we've already armed
DSPCNTR to enable the plane at the next vblank. This causes major
problems for our page flip code which relies on the flip done interrupts
happening at vblank time.

So what happens is that we enable the plane, and immediately allow
userspace to submit a page flip. If the plane is still in the process
of being enabled when the page flip is issued, the flip done gets
signalled immediately. Our DSPSURFLIVE check catches this to prevent
premature flip completion, but it also means that we don't get a flip
done interrupt when the plane actually gets enabled, and so the page
flip is never completed.

Work around this by re-introducing blocking vblank waits on BDW
whenever we enable the primary plane.

I removed some of the vblank waits here:
 commit 6304cd91
 Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
 Date:   Fri Apr 25 13:30:12 2014 +0300

    drm/i915: Drop the excessive vblank waits from modeset codepaths

To avoid these blocking vblank waits we should start using the vblank
interrupt instead of the flip done interrupt to complete page flips.
But that's material for another patch.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79354Tested-by: NGuo Jinxian <jinxianx.guo@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

crtc->primary->fb may be NULL upon entry to intel_pipe_set_base() if the
primary plane has previously been disabled via the universal plane
interface.  We need to check for NULL before trying to reference
old_fb's obj.

This fixes a regression introduced in

        commit a071fa00
        Author: Daniel Vetter <daniel.vetter@ffwll.ch>
        Date:   Wed Jun 18 23:28:09 2014 +0200

        drm/i915: Introduce accurate frontbuffer tracking

Testcase: igt/kms_universal_plane
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

For MIPI, DSI PLL is configured separately in vlv_configure_dsi_pll
during the DSI enable sequence

Causing WARN dump otherwise in dpio_reads

v2: Add IS_CHERRYVIEW check as suggested by Ville
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Jesse noticed that the punit communication needed to query the VLV power
well status can cause substantial delays. Since we can query the state
frequently, for example during I2C transfers, maintain a cached version
of the HW state to get rid of this delay.

This fixes at least one reported regression where boot time increased by
~4 seconds due to frequent power well state queries on VLV during eDP
EDID read.

This regression has been introduced in

commit bb4932c4
Author: Imre Deak <imre.deak@intel.com>
Date:   Mon Apr 14 20:24:33 2014 +0300

    drm/i915: vlv: check port power domain instead of only D0 for eDP VDD on
Reported-by: NJesse Barnes <jesse.barnes@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So these are the guts of the new beast. This tracks when a frontbuffer
gets invalidated (due to frontbuffer rendering) and hence should be
constantly scaned out, and when it's flushed again and can be
compressed/one-shot-upload.

Rules for flushing are simple: The frontbuffer needs one more full
upload starting from the next vblank. Which means that the flushing
can _only_ be called once the frontbuffer update has been latched.

But this poses a problem for pageflips: We can't just delay the
flushing until the pageflip is latched, since that would pose the risk
that we override frontbuffer rendering that has been scheduled
in-between the pageflip ioctl and the actual latching.

To handle this track asynchronous invalidations (and also pageflip)
state per-ring and delay any in-between flushing until the rendering
has completed. And also cancel any delayed flushing if we get a new
invalidation request (whether delayed or not).

Also call intel_mark_fb_busy in both cases in all cases to make sure
that we keep the screen at the highest refresh rate both on flips,
synchronous plane updates and for frontbuffer rendering.

v2: Lots of improvements

Suggestions from Chris:
- Move invalidate/flush in flush_*_domain and set_to_*_domain.
- Drop the flush in busy_ioctl since it's redundant. Was a leftover
  from an earlier concept to track flips/delayed flushes.
- Don't forget about the initial modeset enable/final disable.
  Suggested by Chris.

Track flips accurately, too. Since flips complete independently of
rendering we need to track pending flips in a separate mask. Again if
an invalidate happens we need to cancel the evenutal flush to avoid
races.

v3:
Provide correct header declarations for flip functions. Currently not
needed outside of intel_display.c, but part of the proper interface.

v4: Add proper domain management to fbcon so that the fbcon buffer is
also tracked correctly.

v5: Fixup locking around the fbcon set_to_gtt_domain call.

v6: More comments from Chris:
- Split out fbcon changes.
- Drop superflous checks for potential scanout before calling intel_fb
  functions - we can micro-optimize this later.
- s/intel_fb_/intel_fb_obj_/ to make it clear that this deals in gem
  object. We already have precedence for fb_obj in the pin_and_fence
  functions.

v7: Clarify the semantics of the flip flush handling by renaming
things a bit:
- Don't go through a gem object but take the relevant frontbuffer bits
  directly. These functions center on the plane, the actual object is
  irrelevant - even a flip to the same object as already active should
  cause a flush.
- Add a new intel_frontbuffer_flip for synchronous plane updates. It
  currently just calls intel_frontbuffer_flush since the implemenation
  differs.

This way we achieve a clear split between one-shot update events on
one side and frontbuffer rendering with potentially a very long delay
between the invalidate and flush.

Chris and I also had some discussions about mark_busy and whether it
is appropriate to call from flush. But mark busy is a state which
should be derived from the 3 events (invalidate, flush, flip) we now
have by the users, like psr does by tracking relevant information in
psr.busy_frontbuffer_bits. DRRS (the only real use of mark_busy for
frontbuffer) needs to have similar logic. With that the overall
mark_busy in the core could be removed.

v8: Only when retiring gpu buffers only flush frontbuffer bits we
actually invalidated in a batch. Just for safety since before any
additional usage/invalidate we should always retire current rendering.
Suggested by Chris Wilson.

v9: Actually use intel_frontbuffer_flip in all appropriate places.
Spotted by Chris.

v10: Address more comments from Chris:
- Don't call _flip in set_base when the crtc is inactive, avoids redunancy
  in the modeset case with the initial enabling of all planes.
- Add comments explaining that the initial/final plane enable/disable
  still has work left to do before it's fully generic.

v11: Only invalidate for gtt/cpu access when writing. Spotted by Chris.

v12: s/_flush/_flip/ in intel_overlay.c per Chris' comment.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The downclocking checks a few more things, so not that simple to
convert. Also, this should get unified with the drrs handling and also
use the locking of that. Otoh the drrs locking is about as hapzardous
as no locking, at least on first sight.

For easier conversion ditch the upclocking on unload - we'll turn off
everything anyway.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So from just a quick look we seem to have enough information to
accurately figure out whether a given gem bo is used as a frontbuffer
and where exactly: We have obj->pin_count as a first check with no
false negatives and only negligible false positives. And then we can
just walk the modeset objects and figure out where exactly a buffer is
used as scanout.

Except that we can't due to locking order: If we already hold
dev->struct_mutex we can't acquire any modeset locks, so could
potential chase freed pointers and other evil stuff.

So we need something else. For that introduce a new set of bits
obj->frontbuffer_bits to track where a buffer object is used. That we
can then chase without grabbing any modeset locks.

Of course the consumers of this (DRRS, PSR, FBC, ...) still need to be
able to do their magic both when called from modeset and from gem
code. But that can be easily achieved by adding locks for these
specific subsystems which always nest within either kms or gem
locking.

This patch just adds the relevant update code to all places.

Note that if we ever support multi-planar scanout targets then we need
one frontbuffer tracking bit per attachment point that we expose to
userspace.

v2:
- Fix more oopsen. Oops.
- WARN if we leak obj->frontbuffer_bits when freeing a gem buffer. Fix
  the bugs this brought to light.
- s/update_frontbuffer_bits/update_fb_bits/. More consistent with the
  fb tracking functions (fb for gem object, frontbuffer for raw bits).
  And the function name was way too long.

v3: Size obj->frontbuffer_bits correctly so that all pipes fit in.

v4: Don't update fb bits in set_base on failure. Noticed by Chris.

v5: s/i915_gem_update_fb_bits/i915_gem_track_fb/ Also remove a few
local enum pipe variables which are now no longer needed to make the
function arguments no drop over the 80 char limit.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It doesn't make sense to never again schedule the work, since by the
time we might want to re-enable psr the world might have changed and
we can do it again.

The only exception is when we shut down the pipe, but that's an
entirely different thing and needs to be handled in psr_disable.

Note that later patch will again split psr_exit into psr_invalidate
and psr_flush. But the split is different and this simplification
helps with the transition.

v2: Improve the commit message a bit.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have _enable/_disable interfaces now for the modeset sequence and
intel_edp_psr_exit for workarounds.

The callsites in intel_display.c are all redundant with the modeset
sequence enable/disable calls in intel_ddi.c. The one in
intel_sprite.c is real and needs to be switched to psr_exit.

If this breaks anything then we need to augment the enable/disable
functions accordingly.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch enables the framework for using MMIO based flip calls,
in contrast with the CS based flip calls which are being used currently.

MMIO based flip calls can be enabled on architectures where
Render and Blitter engines reside in different power wells. The
decision to use MMIO flips can be made based on workloads to give
100% residency for Media power well.

v2: The MMIO flips now use the interrupt driven mechanism for issuing the
flips when target seqno is reached. (Incorporating Ville's idea)

v3: Rebasing on latest code. Code restructuring after incorporating
Damien's comments

v4: Addressing Ville's review comments
    -general cleanup
    -updating only base addr instead of calling update_primary_plane
    -extending patch for gen5+ platforms

v5: Addressed Ville's review comments
    -Making mmio flip vs cs flip selection based on module parameter
    -Adding check for DRIVER_MODESET feature in notify_ring before calling
     notify mmio flip.
    -Other changes mostly in function arguments

v6: -Having a seperate function to check condition for using mmio flips (Ville)
    -propogating error code from i915_gem_check_olr (Ville)

v7: -Adding __must_check with i915_gem_check_olr (Chris)
    -Renaming mmio_flip_data to mmio_flip (Chris)
    -Rebasing on latest nightly

v8: -Rebasing on latest code
    -squash 3rd patch in series(mmio setbase vs page flip race) with this patch
    -Added new tiling mode update in intel_do_mmio_flip (Chris)

v9: -check for obj->last_write_seqno being 0 instead of obj->ring being NULL in
intel_postpone_flip, as this is a more restrictive condition (Chris)

v10: -Applied Chris's suggestions for squashing patches 2,3 into this patch.
These patches make the selection of CS vs MMIO flip at the page flip time, and
make the module parameter for using mmio flips as tristate, the states being
'force CS flips', 'force mmio flips', 'driver discretion'.
Changed the logic for driver discretion (Chris)

v11: Minor code cleanup(better readability, fixing whitespace errors, using
lockdep to check mutex locked status in postpone_flip, removal of __must_check
in function definition) (Chris)
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NSourab Gupta <sourab.gupta@intel.com>
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> # snb, ivb
[danvet: Fix up parameter alignement checkpatch spotted.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Spotted while crawling around in the area.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The perfect solution for psr_exit is the hardware tracking the changes and
doing the psr exit by itself. This scenario works for HSW and BDW with some
environments like Gnome and Wayland.

However there are many other scenarios that this isn't true. Mainly one right
now is KDE users on HSW and BDW with PSR on. User would miss many screen
updates. For instances any key typed could be seen only when mouse cursor is
moved. So this patch introduces the ability of trigger PSR exit on kernel side
on some common cases that.

Most of the cases are coverred by psr_exit at set_domain. The remaining cases
are coverred by triggering it at set_domain, busy_ioctl, sw_finish and
mark_busy.

The downside here might be reducing the residency time on the cases this
already work very wall like Gnome environment. But so far let's get focused
on fixinge issues sio PSR couild be used for everybody and we could even
get it enabled by default. Later we can add some alternatives to choose the
level of PSR efficiency over boot flag of even over crtc property.

v2: remove exit from connector_dpms. Daniel pointed this is the wrong way and
also this isn't needed for BDW and HSW anyway.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

obj->framebuffer_references isn't an atomic_t so the decrement needs to
be protected by some lock. struct_mutex seems like the appropriate lock
here, and we may already take it for the obj unref anyway.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The DRM core will translate calls to legacy cursor ioctls into universal
cursor calls automatically, so there's no need to maintain the legacy
cursor support.  This greatly simplifies the transition since we don't
have to handle reference counting differently depending on which cursor
interface was called.

The aim here is to transition to the universal plane interface with
minimal code change.  There's a lot of cleanup that can be done (e.g.,
using state stored in crtc->cursor->fb rather than intel_crtc) that is
left to future patches.

v4:
 - Drop drm_gem_object_unreference() that is no longer needed now that
   we receive the GEM obj directly rather than looking up the ID.
v3:
 - Pass cursor obj to intel_crtc_cursor_set_obj() if cursor fb changes,
   even if 'visible' is false.  intel_crtc_cursor_set_obj() will notice
   that the cursor isn't visible and disable it properly, but we still
   need to get intel_crtc->cursor_addr set properly so that we behave
   properly if the cursor becomes visible again in the future without
   changing the cursor buffer (noted by Chris Wilson and verified
   via i-g-t kms_cursor_crc).
 - s/drm_plane_init/drm_universal_plane_init/.  Due to type
   compatibility between enum and bool, everything actually works
   correctly with the wrong init call, except for the type of plane that
   gets exposed to userspace (it shows up as type 'primary' rather than
   type 'cursor').
v2:
 - Remove duplicate dimension checks on cursor
 - Drop explicit cursor disable from crtc destroy (fb & plane
   destruction will take care of that now)
 - Use DRM plane helper to check update parameters

Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: Pallavi G<pallavi.g@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Refactor cursor buffer setting such that the code to actually update the
cursor lives in a new function, intel_crtc_cursor_set_obj(), and takes
a GEM object as a parameter.  The existing legacy cursor ioctl handler,
intel_crtc_cursor_set() will now perform the userspace handle lookup and
then call this new function.

This refactoring is in preparation for the universal plane cursor
support where we'll want to update the cursor with an actual GEM buffer
object (obtained via drm_framebuffer) rather than a userspace handle.

v2:  Drop obvious kerneldoc and replace with note about function's
     reference consumption
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: Pallavi G<pallavi.g@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>