When fractional m2 divider isn't used on CHV the fractional part
is ignore by the hardware. Despite that, program the fractional
value (0 in this case) to the hardware register just to keep
things a bit more consistent. Might at least make register dumps
a bit less confusing when there isn't some stale fractional part
hanging around.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The current versions of these two macros don't work correctly if the
argument expression happens to contain a modulo operator (%) -- when
stringified, it gets interpreted as a printf formatting character!
With a specifically crafted parameter, this could probably cause a
kernel OOPS; consider WARN_ON(p%s) or WARN_ON(f %*pEp).

Instead, we should use an explicit "%s" format, with the stringified
expression as the coresponding literal-string argument.
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With MST there won't be a crtc assigned to the main link encoder, so
trying to dig up the pipe_config from there is a recipe for an oops.

Instead store the parameters (lane_count and link_rate) in the encoder,
and use those values during link training etc. Since those parameters
are now assigned only when the link is actually enabled,
.compute_config() won't clobber them as it did before.

Hardware state readout is still bonkers though as we don't transfer the
link parameters from pipe_config intel_dp. We should do that during
encoder sanitation. But since we don't even do a proper job of reading
out the main link encoder state for MST there's littel point in
worrying about this now.

Fixes a regression with MST caused by:
 commit 90a6b7b0
 Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
 Date:   Mon Jul 6 16:39:15 2015 +0300

    drm/i915: Move intel_dp->lane_count into pipe_config

v2: Different apporoach that should keep intel_dp_check_mst_status()
    somewhat less oopsy

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Due to a coherency issue on BXT A steppings we can't guarantee a
coherent view of cached (CPU snooped) GPU mappings, so fail such
requests. User space is supposed to fall back to uncached mappings in
this case.

v2:
- limit the WA to A steppings, on later stepping this HW issue is fixed
v3:
- return error instead of trying to work around the issue in kernel,
  since that could confuse user space (Chris)

Testcast: igt/gem_store_dword_batches_loop/cached-mapping
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By running igt/store_dword_loop_render on BXT we can hit a coherency
problem where the seqno written at GPU command completion time is not
seen by the CPU. This results in __i915_wait_request seeing the stale
seqno and not completing the request (not considering the lost
interrupt/GPU reset mechanism). I also verified that this isn't a case
of a lost interrupt, or that the command didn't complete somehow: when
the coherency issue occured I read the seqno via an uncached GTT mapping
too. While the cached version of the seqno still showed the stale value
the one read via the uncached mapping was the correct one.

Work around this issue by clflushing the corresponding CPU cacheline
following any store of the seqno and preceding any reading of it. When
reading it do this only when the caller expects a coherent view.

v2:
- fix using the proper logical && instead of a bitwise & (Jani, Mika)
- limit the workaround to A stepping, on later steppings this HW issue
  is fixed
v3:
- use a separate get_seqno/set_seqno vfunc (Chris)

Testcase: igt/store_dword_loop_render
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We also need to call the frontbuffer flip to trigger proper
invalidations when disabling planes. Otherwise we will miss
screen updates when disabling sprites or cursor.

On core platforms where HW tracking also works, this issue
is totally masked because HW tracking triggers PSR exit
however on VLV/CHV that has only SW tracking we miss screen
updates when disabling planes.

It was caught with kms_psr_sink_crc sprite_plane_onoff
and cursor_plane_onoff subtests running on VLV/CHV.

This is probably a regression since I can also get this
with the manual test case, but with so many changes on atomic
modeset I couldn't track exactly when this was introduced.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

MI_STORE_REGISTER_MEM, MI_LOAD_REGISTER_MEM instructions are not really
variable length instructions unlike MI_LOAD_REGISTER_IMM where it expects
(reg, addr) pairs so use fixed length for these instructions.

v2: rebase

Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
[danvet: Appease checkpatch as Mika spotted in i915_reg.h - it seems
terminally unhappy about i915_cmd_parser.c so that would be a separate
patch.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In commit
 d1675198: drm/i915: Integrate GuC-based command submission

the drm.tmpl include lines reference the intel_guc_submission.c but the
patch adds the file i915_guc_submission.c. drm.tmpl fails to build with:
 docproc: .//drivers/gpu/drm/i915/intel_guc_submission.c:
  No such file or directory

Change the file reference to the actual file.
Signed-off-by: NGraham Whaley <graham.whaley@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There's so much scaler debugging messages that it makes other debugging
hard. Remove them.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This provides a means of reading status and counts relating
to GuC actions and submissions.

v2:
    Remove surplus blank line in output [Chris Wilson]

v5:
    Added GuC per-engine submission & seqno statistics

v6:
    Add per-ring statistics to client, refactor client-dumper.
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Signed-off-by: NAlex Dai <yu.dai@intel.com>
Reviewed-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

GuC-based submission is mostly the same as execlist mode, up to
intel_logical_ring_advance_and_submit(), where the context being
dispatched would be added to the execlist queue; at this point
we submit the context to the GuC backend instead.

There are, however, a few other changes also required, notably:
1.  Contexts must be pinned at GGTT addresses accessible by the GuC
    i.e. NOT in the range [0..WOPCM_SIZE), so we have to add the
    PIN_OFFSET_BIAS flag to the relevant GGTT-pinning calls.

2.  The GuC's TLB must be invalidated after a context is pinned at
    a new GGTT address.

3.  GuC firmware uses the one page before Ring Context as shared data.
    Therefore, whenever driver wants to get base address of LRC, we
    will offset one page for it. LRC_PPHWSP_PN is defined as the page
    number of LRCA.

4.  In the work queue used to pass requests to the GuC, the GuC
    firmware requires the ring-tail-offset to be represented as an
    11-bit value, expressed in QWords. Therefore, the ringbuffer
    size must be reduced to the representable range (4 pages).

v2:
    Defer adding #defines until needed [Chris Wilson]
    Rationalise type declarations [Chris Wilson]

v4:
    Squashed kerneldoc patch into here [Daniel Vetter]

v5:
    Update request->tail in code common to both GuC and execlist modes.
    Add a private version of lr_context_update(), as sharing the
        execlist version leads to race conditions when the CPU and
        the GuC both update TAIL in the context image.
    Conversion of error-captured HWS page to string must account
        for offset from start of object to actual HWS (LRC_PPHWSP_PN).

Issue: VIZ-4884
Signed-off-by: NAlex Dai <yu.dai@intel.com>
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Turn on interrupt steering to route necessary interrupts to GuC.

v6:
    Rebased

Issue: VIZ-4884
Signed-off-by: NAlex Dai <yu.dai@intel.com>
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A GuC client has its own doorbell and workqueue. It maintains the
doorbell cache line, process description object and work queue item.

A default guc_client is created for the i915 driver to use for
normal-priority in-order submission.

Note that the created client is not yet ready for use; doorbell
allocation will fail as we haven't yet linked the GuC's context
descriptor to the default contexts for each ring (see later patch).

v2:
    Defer adding structure members until needed [Chris Wilson]
    Rationalise type declarations [Chris Wilson]

v5:
    Add GuC per-engine submission & seqno statistics.
    Move wq locking to encompass both get_space() and add_item().
    Take forcewake lock in host2guc_action() [Tom O'Rourke]

v6:
    Fix GuC doorbell cacheline selection code (the
        cacheline-within-page calculation was wrong).
    Rename GuC priorities to make them closer to the names used in
        the GuC firmware source, matching what the autogenerated
        versions will (probably) be.
    Add per-ring statistics to client.

Issue: VIZ-4884
Signed-off-by: NAlex Dai <yu.dai@intel.com>
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Allocate a GEM object to hold GuC log data. A debugfs interface
(i915_guc_log_dump) is provided to print out the log content.

v2:
    Add struct members at point of use [Chris Wilson]

v6:
    Rebased

Issue: VIZ-4884
Signed-off-by: NAlex Dai <yu.dai@intel.com>
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This adds the first of the data structures used to communicate with the
GuC (the pool of guc_context structures).

We create a GuC-specific wrapper round the GEM object allocator as all
GEM objects shared with the GuC must be pinned into GGTT space at an
address that is NOT in the range [0..WOPCM_TOP), as that range of GGTT
addresses is not accessible to the GuC (from the GuC's point of view,
it's permanently reserved for other objects such as the BootROM & SRAM).

Later, we will need to allocate additional GuC-sharable objects for the
submission client(s) and the GuC's debug log.

v2:
    Remove redundant initialisation [Chris Wilson]
    Defer adding struct members until needed [Chris Wilson]
    Local functions should pass dev_priv rather than dev [Chris Wilson]

v5:
    Invalidate GuC TLB after allocating and pinning a new object

v6:
    Rebased

Issue: VIZ-4884
Signed-off-by: NAlex Dai <yu.dai@intel.com>
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

GuC submission is basically execlist submission, but with the GuC
handling the actual writes to the ELSP and the resulting context
switch interrupts.  So to describe a context for submission via
the GuC, we need one of the same functions used in execlist mode.
This commit exposes one such function, changing its name to better
describe what it does (it's related to logical ring contexts rather
than to execlists per se).

v2:
    Replaces previous "drm/i915: Move execlists defines from .c to .h"

v3:
    Incorporates a change to one of the functions exposed here that was
        previously part of an internal patch, but which was omitted from
        the version recently committed to drm-intel-nightly:
	    7a01a0a2 drm/i915/lrc: Update PDPx registers with lri commands
        So we reinstate this change here.

v4:
    Drop v3 change, update function parameters due to collision with
        8ee36152 drm/i915: Convert execlists_ctx_descriptor() for requests

v5:
    Don't expose execlists_update_context() after all. The current
        version is no longer compatible with GuC submission; trying to
        share the execlist version of this function results in both GuC
        and CPU updating TAIL in the context image, with bad results when
        they get out of step. The GuC submission path now has its own
        private version that just updates the ringbuffer start address,
        and not TAIL or PDPx.

v6:
    Rebased

Issue: VIZ-4884
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The new node provides access to the status of the GuC-specific loader;
also the scratch registers used for communication between the i915
driver and the GuC firmware.

v2:
    Changes to output formats per Chris Wilson's suggestions

v6:
    Rebased

Issue: VIZ-4884
Signed-off-by: NAlex Dai <yu.dai@intel.com>
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This fetches the required firmware image from the filesystem,
then loads it into the GuC's memory via a dedicated DMA engine.

This patch is derived from GuC loading work originally done by
Vinit Azad and Ben Widawsky.

v2:
    Various improvements per review comments by Chris Wilson

v3:
    Removed 'wait' parameter to intel_guc_ucode_load() as firmware
        prefetch is no longer supported in the common firmware loader,
	per Daniel Vetter's request.
    Firmware checker callback fn now returns errno rather than bool.

v4:
    Squash uC-independent code into GuC-specifc loader [Daniel Vetter]
    Don't keep the driver working (by falling back to execlist mode)
        if GuC firmware loading fails [Daniel Vetter]

v5:
    Clarify WOPCM-related #defines [Tom O'Rourke]
    Delete obsolete code no longer required with current h/w & f/w
        [Tom O'Rourke]
    Move the call to intel_guc_ucode_init() later, so that it can
        allocate GEM objects, and have it fetch the firmware; then
	intel_guc_ucode_load() doesn't need to fetch it later.
        [Daniel Vetter].

v6:
    Update comment describing intel_guc_ucode_load() [Tom O'Rourke]

Issue: VIZ-4884
Signed-off-by: NAlex Dai <yu.dai@intel.com>
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We only need the link_bw/rate_select parameters when starting link
training, and they should be computed based on the currently active
config, so throw them out from intel_dp and just compute on demand.

Toss in an extra debug print to see rate_select in addition to link_bw,
as the latter may be 0 for eDP 1.4.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_dp->link_bw is going away, so consul the port_clock instead when
choosing between TP1 and TP3.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently we clobber intel_dp->lane_count in compute config, which means
after a rejected modeset we may no longer be able to retrain the current
link. Move lane_count into pipe_config to avoid that.

v2: Add missing ':' to the pipe config debug dump
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use a separate variable for the TRANS_DP_CTL value instead of reusing
'tmp' that otherwise contains the DP port register value.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

All the *_ddi_pll_select() functions get passed the port_clock and pipe
config as parameters. We only need to pass the pipe config, and the
functions can dig up the port_clock themselves.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use port_clock instead of link_bw when picking the PLL parameters for
DP. link_bw may be zero with an eDP 1.4 sink that supports
DP_LINK_RATE_SET so we shouldn't use it for anything other than feed it
to the sink appropriately.

v2: Fix typo in commit message (Sivakumar)
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently we treat intel_{dp,hdmi}->color_range as partly user
controller value (via the property) but we also change it during
.compute_config() when using the "Automatic" mode. That is a bit
confusing, so let's just change things so that we store the user
property values in intel_dp, and only change what's stored in
pipe_config during .compute_config().

There should be no functional change.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When we queue the command or operation to change the scanout address, we
mark the flip as in progress. We can use this flag to prevent us from
checking for a stalled flip prior to its existence!
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently we don't clflush on pin_to_display if the bo is already
UC/WT and is not in the CPU write domain. This causes problems with
pwrite since pwrite doesn't change the write domain, and it avoids
clflushing on UC/WT buffers on LLC platforms unless the buffer is
currently being scanned out.

Fix the problem by marking the cache dirty and adjusting
i915_gem_object_set_cache_level() to clflush when the cache is dirty
even if the cache_level doesn't change.

My last attempt [1] at fixing this via write domain frobbing was shot
down, but now with the cache_dirty flag we can do things in a nicer way.

[1] http://lists.freedesktop.org/archives/intel-gfx/2014-November/055390.html

v2: Drop the I915_CACHE_NONE/WT checks from pwrite

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86422
Testcase: igt/kms_pwrite_crc
Testcase: igt/gem_pwrite_snooped
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

WA for BXT A0/A1, where DDIB's HPD pin is swapped to DDIA, so enabling
DDIA HPD pin in place of DDIB.

v2: For DP, irq_port is used to determine the encoder instead of
hpd_pin and removing the edp HPD logic because port A HPD is not
present(Imre)
v3: Rebased on top of Imre's patchset for enabling HPD on PORT A.
Added hpd_pin swapping for intel_dp_init_connector, setting encoder
for PORT_A as per the WA in irq_port (Imre)
v4: Dont enable interrupt for edp, also reframe the description (Siva)
v5: Don’t check for PORT_A in intel_ddi_init to update dig_port,
instead avoid setting hpd_pin itself (Imre)
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Also remove redundant comments.
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And fix 0-DAY kernel test infrastructure warning.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the offset length being taken care of in ("drm/i915/gtt: Allow >=
4GB offsets in X86_32"), the code should be finally safe in 32-bit
kernels.

This reverts commit 501fd70f
Author: Michel Thierry <michel.thierry@intel.com>
Date:   Fri May 29 14:15:05 2015 +0100

    drm/i915: limit PPGTT size to 2GB in 32-bit platforms
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Similar to commit c44ef60e ("drm/i915/gtt:
Allow >= 4GB sizes for vm"), i915_gem_obj_offset and i915_gem_obj_ggtt_offset
return an unsigned long, which in only 4-bytes long in 32-bit kernels.

Change return type (and other related offset variables) to u64.

Since Global GTT is always limited to 4GB, this change would not be required
in i915_gem_obj_ggtt_offset, but this is done for consistency.

v2: Remove unnecessary offset variable in do_pin, as we already have
    vma->node.start (Chris).
    Update GGTT offset too (Tvrtko).

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By Vesa DP 1.2 spec TEST_CRC_COUNT is a "4 bit wrap counter which
increments each time the TEST_CRC_x_x are updated."

However if we are trying to verify the screen hasn't changed we get
same (count, crc) pair twice. Without this patch we would return
-ETIMEOUT in this case.

So, if in 6 vblanks the pair (count, crc) hasn't changed we
return it anyway instead of returning error and let test case decide
if it was right or not.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By Vesa DP 1.2 Spec TEST_CRC_COUNT should be
"reset to 0 when TEST_SINK bit 0 = 0."

However for some strange reason when PSR is enabled in
certain platforms this is not true. At least not immediatelly.

So we face cases like this:

first get_sink_crc operation:
	     count: 0, crc: 000000000000
	     count: 1, crc: c101c101c101
returned expected crc: c101c101c101

secont get_sink_crc operation:
	     count: 1, crc: c101c101c101
	     count: 0, crc: 000000000000
	     count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000

But also the reset to 0 should be faster resulting into:

get_sink_crc operation:
	     count: 1, crc: c101c101c101
	     count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000

So in order to know that the second one is valid one
we need to compare the pair (count, crc) with latest (count, crc).

If the pair changed you have your valid CRC.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By Vesa DP spec, test counter at DP_TEST_SINK_MISC just reset to 0
when unsetting DP_TEST_SINK_START, so let's force this stop here.

But let's minimize the aux transactions and just do it when we know
it hasn't been properly stoped.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

GTT was only 32b and its max value is 4GB. In order to allow objects
bigger than 4GB in 48b PPGTT, i915_gem_userptr_ioctl we could check
against max 48b range (1ULL << 48).

But since the check no longer applies, just kill the limit.

v2: Use the default ctx to infer the ppgtt max size (Akash).
v3: Just kill the limit, it was only there for early detection of an
error when used for execbuffer (Chris).

Cc: Akash Goel <akash.goel@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise it can overflow in 48-bit mode, and cause an incorrect
exec_start.

Before commit 5f19e2bf ("drm/i915: Merged
the many do_execbuf() parameters into a structure"), it was already an u64.
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In a 48b world, users can try to allocate buffers bigger than 4GB; in
these cases it is important that size is a 64b variable.

v2: Drop the warning about bind with size 0, it shouldn't happen anyway.
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Clean up patch after rebases.
v3: gen8_dump_ppgtt for 32b and 48b PPGTT.
v4: Use used_pml4es/pdpes (Akash).
v5: Rebase after Mika's ppgtt cleanup / scratch merge patch series.
v6: Rely on used_px bits instead of null checking (Akash)

Cc: Akash Goel <akash.goel@intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: For semaphore errors, object is mapped to GGTT and offset will not
be > 4GB, print only lower 32-bits (Akash)
v3: Print gtt_offset in groups of 32-bit (Chris)

Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>